This article presents a miniaturized wake-up receiver (WuRX) that is temperature-compensated yet still consumes only 22.3 nW (7.3 nW excluding the temperature-compensation blocks) while operating at 9 GHz (X-band). By moving the carrier frequency to 9 GHz and designing a high impedance, passive envelope detector (ED), the transformer size is reduced to 0.02 cm² while still achieving 13.5 dB of passive RF voltage gain. To further reduce the area, a global common-mode feedback (CMFB) technique is utilized across the ED and baseband (BB) amplifier that eliminates the need for off-chip ac -coupling components. Multiple temperature-compensation techniques are proposed to maintain constant bandwidth of the signal path and constant clock frequency. The WuRX was implemented in 65- (RF) and 180-nm (BB) CMOS and achieves -69.5- and -64-dBm sensitivity with and without an antenna, respectively. Importantly, the sensitivity is demonstrated to vary by only 3 dB from -10 to 40 °C. This article demonstrates state-of-the-art performance for WuRXs operating at >1 GHz while achieving the smallest area and best temperature insensitivity.
7 December 2021 in IEEE Transactions on Biomedical Circuits and Systems
This paper presents a second-order voltage-controlled oscillator (VCO)-based front-end for the direct digitization of biopotential signals. This work addresses the non-linearity of VCO-based ADC architectures with a mismatch resilient, multi-phase quantizer, a gated-inverted-ring oscillator (GIRO), achieving >110-dB SFDR. Leveraging the time-domain encoding of the first integrator, the ADC's power is dynamically scaled with the input amplitude enabling up to 35% power savings in the absence of motion artifacts or interference. An auxiliary input-impedance booster increases the ADC's input impedance to 50 MΩ across the entire bandwidth. Fabricated in a 65-nm CMOS process, this ADC achieves 92.3-dB SNDR in a 1 kHz BW while consuming 5.8 µW for a 174.7 dB Schreier FoM.
Next-generation wearable devices will enable clinical-grade, continuous ExG (ECG, EEG, EMG, etc.) biopotential monitoring, providing medical professionals with valuable longitudinal data outside of hospital settings. These devices must be ultra-low power $(\lt 10 \mu W)$ to enable long battery life while accurately digitizing sub-kHz, $\mu V-$level ExG signals in the presence of large motion and/or stimulation artifacts $(\gt 100$ mV) with high input-impedance $(Z_{in}\gt 10M\Omega)$ to avoid signal attenuation. Achieving such performance with conventional PGA + ADC architectures is challenging due to the conflicting low-power and $\gt 90$ dB dynamic-range (DR) requirements [1]. To address this, several direct digitization analog front-ends (AFEs) have been reported [2]–[4]. While these offer wide DR, they typically have low input-impedance $(\lt 5 M\Omega)$ and/or low power-efficiency (FoM $\le 172$ dB). This paper presents a scalable $2^{nd}-$ order voltage-controlled oscillator (VCO)-only $\Delta \sum$ ADC that achieves 92.3dB SNDR in a 1kHz bandwidth using a mismatch tolerant, multiphase gated-inverted ring-oscillator (GIRO) quantizer with dynamic power-scaling. The ADC uses an impedance-booster to maintain $\gt 50 M\Omega$ input-impedance over the entire bandwidth while consuming $4.25 \mu W$ during nominal operation and $5.8 \mu W$ in the presence of artifacts resulting in an FoM of 174.7dB.
6 January 2021 in IEEE Journal of Solid-State Circuits
This article reports a low-noise magnetic sensor front-end with an 18-bit Zoom ADC for detecting temporal magnetic nanoparticle (MNP) relaxation. Techniques such as dynamic element matching (DEM) and magnetoresistive correlated double sampling (MRCDS) are proposed to remove the sensor and analog front-end (AFE) 1/ ${f}$ noise while a fast-settling Miller compensation (FSMC) technique is proposed to reduce the amplifier power. Collectively, these result in state-of-the-art input-referred noise performance (9.7 nT rms ) and a figure-of-merit (FoM) that is 6.6 $\times $ and 210 $\times $ better than previously reported magnetic sensor and relaxation-based AFEs, respectively. A relaxation-based magnetic immunoassay (MIA) was performed to demonstrate the concept. This design is implemented in a 0.18- $\mu \text{m}$ CMOS process and consumes 4.32 mW from a 1.8-V supply.
27 October 2022 in IEEE Journal of Solid-State Circuits
This article presents a third-order voltage-controlled oscillator (VCO)-based analog-to-digital converter (ADC) that leverages pseudo-virtual ground (PVG) feedforwarding (FF), linearizing the VCOs and enabling higher order noise shaping with a single feedback digital-to-analog converter. This technique leads to a power-efficient ADC implementation with a wide dynamic range. The ADC is fabricated in a 65-nm process and achieves a 92.1-dB SNDR in a 2.5-kHz bandwidth. This results in a state-of-the-art 179.6-dB figure-of-merit (FoM) among previously published VCO-based ADCs. The PVG FF technique allows the ADC to attain extremely high linearity, 123-dB peak SFDR, with a wide 1.8-Vpp differential input range. The ADC maintains performance with up to 200-mV variation on the 0.8-V supply and across temperatures from 0 to 70 °C.
20 August 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief reports a high-performance, low-power temperature sensor suitable for wireless IoT devices/RFID tags. The system utilizes a mostly digital approach to achieve energy-efficient, sub- $\mu \text{W}$ operation with a resistor-based temperature sensor. A sampled, incomplete-settling, switched-capacitor-based Wheatstone bridge is read out using a digital frequency-locked loop (DFLL) while harnessing the quasi-periodic limit cycles to reduce in-band noise. Implemented in a 65 nm CMOS process, it consumes 310 nW and achieves 9.8 mK resolution in a 10 ms conversion time. This results in a 297 fJ ${\mathrm {\cdot }}\text{K}~^{2}$ figure-of-merit (FoM) and low energy (3.1 nJ/meas.).