Department of Technical Computer Science, Faculty of Mathematics and Information Technology, Lublin University of Technology, Nadbystrzycka 38, 20-618 Lublin, Poland
Auto-generated profile, based on publicly available information
Magda Wlazło
Department of Technical Computer Science, Faculty of Mathematics and Information Technology, Lublin University of Technology, Nadbystrzycka 38, 20-618 Lublin, Poland
The measurement of the moisture content of building materials is of key importance both in the process of building structures and in their subsequent operation. In engineering practice, indirect techniques of moisture measurement, mainly, resistance and capacitive, are the most popular. The main objective of this research work was to compare the classic TDR measurement technique to the non-invasive, surface TDR sensors. Moisture measurements were carried out on samples made of cellular concrete with density class of 400 and 600. These samples were moist to various degrees, from 0 to 69% (400 c.c.) and from 0 to 55 (600 c.c.). For each sample, five measurements were carried out. Both the RMSE and the expanded uncertainty values were more favorable for the TDR FP/mts probe and were consistent with the literature data. Compared to them, the measurement result for the 400 c.c. samples with the S1 probe was 154.6%, and that with the S2 probe was 87.03% of the values obtained with the invasive probe. When measuring the 600 c.c. samples, we found values of 122.16% for S1 and of 120.1% for S2 of those obtained with the invasive probe. The use of surface TDR sensors provided an easy and quick measurement without damaging the surface and structure of the tested material, as there was no need to introduce the probe actuators inside the tested material.
This paper focuses on the microstructure and tribological properties of novel hardfacing alloy based on Fe-C-Mn-B doped with Ni, Cr, and Si. The 4 mm-thick coating was deposited on the AISI 1045 carbon steel by the MIG-welding method using flux-cored wires in three passes. The transition zone thickness between the weld layers was ~80 μm, and the width of the substrate-coating interface was 5–10 μm. The following coating constituents were detected: coarser elongated M2B borides, finer particles of Cr7C3 carbides, and an Fe-based matrix consisting of ferrite and austenite. The nanohardness of the matrix was ~5–6 GPa, carbides ~16–19 GPa, and borides 22–23 GPa. A high cooling rate during coating fabrication leads to the formation of a fine mesh of M7C3 carbides; borides grow in the direction of heat removal, from the substrate to the friction surface, while in the transition zone, carbides become coarser. The dry sliding friction tests using a tribometer in PoD configuration were carried out at contact pressure 4, 7, 10, and 15 MPa against the AISI 1045 carbon steel (water-quenched and low-tempered, 50–52 HRC). The leading wear phenomenon at 4 and 7 MPa is fatigue, and at 10 and 15 MPa it is oxidation and delamination.
This study explores the application of materials used in 3D printing to manufacture the housings of non-invasive sensors employed in measurements using a TDR (Time Domain Reflectometry) meter. The research investigates whether sensors designed with 3D printing technology can serve as viable alternatives to conventional invasive and non-invasive sensors. This study focuses on innovative approaches to designing humidity sensors, utilizing Fused Deposition Modeling (FDM) technology to create housings for non-invasive sensors compatible with TDR devices. The paper discusses the use of 3D modeling technology in sensor design, with particular emphasis on materials used in 3D printing, notably polylactic acid (PLA). Environmental factors, such as moisture in building materials, are characterized, and the need for dedicated sensor designs is highlighted. The software utilized in the 3D modeling and printing processes is also described. The Materials and Methods Section provides a detailed account of the construction process for the non-invasive sensor housing and the preparation for moisture measurement in silicate materials using the designed sensor. A prototype sensor was successfully fabricated through 3D printing. Using the designed sensor, measurements were conducted on silicate samples soaked in aqueous solutions with water absorption levels ranging from 0% to 10%. Experimental validation involved testing silicate samples with the prototype sensor to evaluate its effectiveness. The electrical permittivity of the material was calculated, and the root-mean-square error (RMSE) was determined using classical computational methods and machine learning techniques. The RMSE obtained using the classical method was 0.70. The results obtained were further analyzed using machine learning models, including Gaussian Process Regression (GPR) and Support Vector Machine (SVM). The GPR model achieved an RMSE of 0.15, while the SVM model yielded an RMSE of 0.25. These findings confirm the sensor’s effectiveness and its potential for further research and practical applications.
1 November 2022 in Advances in Science and Technology Research Journal
The article focuses on the subject of 3D printing. 3D printing technology and currently used solutions are described. The materials used in printing with the use of a filament printer and a resin printer are discussed. The fused deposiotion modeling technique and the LCD-based stereolithography....
1 December 2023 in Journal of Ecological Engineering
3D printing is a modern technology that enables the creation of three-dimensional objects from various thermoplastic copolymers. One of the challenges of 3D printing is providing adequate support for complex shapes that may fall apart or deform during the printing process. Traditionally, support...
1 October 2026 in Advances in Science and Technology Research Journal
The objective of this study is to estimate the concentration of selected microbial volatile organic compounds (mVOCs), namely ethylbenzene, cumene, and limonene, using multi-sensor gas arrays combined with statistical regression and machine learning methods. Two sensor array configurations were...