The commercialization of electronic devices based on graphene has not yet been successful, even 20 years after its first isolation. To this end, the European Commission is supporting research toward establishing a European experimental pilot line for electronic and optoelectronic devices based on graphene and related two-dimensional (2D) materials, namely the Experimental Pilot Line (2D-EPL) project. Here, we report the results obtained during the first and third multi-project wafer (MPW) runs completed at the end of 2022 (MPW run 1) and 2023 (MPW run 3) as an outcome of the 2D-EPL. Test devices were measured across the wafers to assess the device quality and variability before delivering the fabricated dies to the customers. Raman spectroscopy confirmed minimal structural changes in the graphene caused by the fabrication process, while electrical measurements of two different device types verified the device specifications defined in the process design kit.
Hexagonal boron nitride (h-BN) is well-established as a requisite support, encapsulant and barrier for 2D material technologies, but also recently as an active material for applications ranging from hyperbolic metasurfaces to room temperature single-photon sources. Cost-effective, scalable and high quality growth techniques for h-BN layers are critically required. We utilise widely-available iron foils for the catalytic chemical vapour deposition (CVD) of h-BN and report on the significant role of bulk dissolved species in h-BN CVD, and specifically, the balance between dissolved oxygen and carbon. A simple pre-growth conditioning step of the iron foils enables us to tailor an error-tolerant scalable CVD process to give exceptionally large h-BN monolayer domains. We also develop a facile method for the improved transfer of as-grown h-BN away from the iron surface by means of the controlled humidity oxidation and subsequent rapid etching of a thin interfacial iron oxide; thus, avoiding the impurities from the bulk of the foil. We demonstrate wafer-scale (2″) production and utilise this h-BN as a protective layer for graphene towards integrated (opto-)electronic device fabrication.
Developing electronic devices capable of emulating biological functions is essential for advancing brain-inspired computation paradigms such as neuromorphic computing. In recent years, two-dimensional materials have emerged as promising candidates for neuromorphic electronic devices. This work addresses the coexistence of volatile and nonvolatile resistive switching in lateral memristors based on molybdenum disulfide with silver as the active electrode. The fabricated devices exhibited switching voltages of ∼0.16 V and ∼0.52 V for volatile and nonvolatile operation, respectively, under direct-current measurements. They also displayed the essential synaptic functions of paired-pulse facilitation and short- and long-term plasticity under pulse stimulation. The operation mechanism was investigated by in situ transmission electron microscopy, which showed lateral migration of silver ions along the molybdenum disulfide between electrodes. Based on the experimental data, a macroscopic semiclassical electron transport model was used to reproduce the current-voltage characteristics and support the proposed underlying switching mechanisms.
The deposition of dielectric materials on graphene is one of the bottlenecks for unlocking the potential of graphene in electronic applications. The plasma enhanced atomic layer deposition of 10 nm thin high quality aluminum oxide (Al2O3) on graphene is demonstrated using a monolayer of hexagonal boron nitride (hBN) as protection layer. Raman spectroscopy is performed to analyze possible structural changes of the graphene lattice caused by the plasma deposition. The results show that a monolayer of hBN in combination with an optimized deposition process can effectively protect graphene from damage, while significant damage is observed without an hBN layer. Electrical characterization of double gated graphene field effect devices confirms that the graphene does not degrade during the plasma deposition of Al2O3. The leakage current densities are consistently below 1 pA µm−2 for electric fields across the insulators of up to 8 MV cm−1, with irreversible breakdown happening above. Such breakdown electric fields are typical for Al2O3 and can be seen as an indicator for high quality dielectric films.
Memristors based on 2D materials have garnered significant attention. Their fast resistive switching (RS) behavior and atomic‐level thickness enable low power consumption, making them promising candidates for neuromorphic computing. Among these, memristors based on molybdenum disulfide (MoS 2 ) have been extensively studied. Their RS has been attributed to the formation and rupture of conductive filaments (CFs). However, the underlying mechanism of filament formation remains underexplored, and the inherently stochastic nature of RS leads to high variability and limited reproducibility. In this study, we demonstrate wafer‐scale memristors based on metal–organic chemical vapor‐deposited MoS 2 . Our devices exhibit both volatile and nonvolatile RS behaviors, tunable by modulating the current compliance. Notably, we observe stable RS characteristics in an intermediate resistive state (IRS), set and reset voltages within ±1 V, endurance of over 2500 cycles, and state retention over 10 6 s. Among 100 tested devices, 98 exhibited IRS behavior, confirming a high yield (98%) and demonstrating its robust and reproducible RS nature. Combined experimental and simulation results further indicate that the IRS arises from the lateral growth of CFs in the van der Waals gaps. Furthermore, the devices successfully emulate synaptic plasticity with current responses on a microsecond timescale, highlighting their potential for large‐scale integration in neuromorphic computing architectures.
The spin‐polarized surface states in topological insulators offer unique transport characteristics that make them distinguishable from trivial conductors. Herein, the impact of these surface states in the topological insulator BiSbTeSe 2 is detected by electrical means using a nonlocal (NL) transport configuration with ferromagnetic Co/Al 2 O 3 electrodes. It is shown that the NL measurement allows probing of the surface currents flowing along the whole surface, i.e., from the top along the side to the bottom surface and back to the top surface along the opposite side. Increasing the temperature increases the interaction between bulk and surface states, which shortens this NL current path along the surface and hence leads to a complete disappearance of the NL signal at around 20 K. Interestingly, it is observed that the ratio between spin signal to background signal is much larger in the NL geometry compared to the local one. Given that the observed ratio in the NL geometry aligns well with expectations for spin‐polarized surface states, the findings suggest that an as‐yet unresolved mechanism diminishes the spin signal in the local geometry.