A novel dual-polarized frequency-selective polarization converter (FSPC) with low-backward scattering is proposed by combing a band-pass frequency selective surface (FSS) with a polarization converter. The FSPC, comprised of the top polarization conversion layer and the bottom multi-layer band-pass FSS, is formed by introducing two polarization converter bands on both sides of the broadband passband. The four-port equivalent circuit model cascading FSS and polarization converter is proposed and investigated. It is numerically demonstrated that a flat 1dB transmission window can be obtained from 8.5GHz to 11GHz with a 25.6% fractional bandwidth (FBW), and the bandwidth of reflection below -10dB is up to 92% from 5.6GHz to 15.13GHz. Moreover, the proposed device can achieve two polarization conversion bands (5.66GHz-6.9GHz and 12.8GHz-15.2GHz) with the polarization conversion ratio over 90%. Besides, by arranging the proposed structure in a checkerboard-like distribution, the backward scattering energy can be reduced in a wide frequency band ranging from 4.5GHz to 16GHz. Both simulation and experimental results are in good agreement, which demonstrates our design strategy. Compared with the conventional polarization converters, the proposed design presents an extra frequency-selective performance and hence can be a great substitute for the frequency selective rasorber (FSR).
A Fabry–Perot (FP) antenna with high gain-bandwidth product (GBP) and wideband radar cross section (RCS) reduction is proposed using an embedded chessboard polarization conversion metasurface (CPCM). A polarization conversion metasurface (PCM) unit and its mirror unit are etched on both sides of a dielectric substrate with chessboard arrangement to form a CPCM. The in-band and out-of-band low-RCS features of the FP antenna are realized by destructive interference, and the high GBP is attributed to the FP resonant cavity. Moreover, an additional small CPCM designed for another PCM unit is embedded into the original CPCM to construct an embedded CPCM, which helps to improve in-band RCS reduction and has a positive effect on gain enhancement and 10-dB impedance bandwidth. The measured results show that the FP antenna with embedded CPCM has a 10-dB return-loss bandwidth of 8.48-12.21 GHz (36.1%), a GBP of 1338, a 3-dB gain bandwidth of 8.9-11.5 GHz (25.5%) and a maximum realized gain of 17.2 dBi. Meanwhile, the measured RCS reduction band covers 8–26 GHz (105.9%) with a peak RCS reduction of 21.2 dB at 9.4 GHz.
In this paper, an asymmetric Mach-Zehnder interferometer with straight waveguide arms based integrated optical electric field sensor is proposed. Compared with the present reported integrated optical electric field sensors, the proposed sensor has relatively lower transmission loss, higher extinction ratio, much larger linear measurable range, and better thermal stability. The transmission loss of the device is demonstrated to be as low as 6 dB and the extinction ratio is as high as 35 dB. Moreover, the sensor has a linear measurable range of approximately 34 dB and the minimal detectable electric field strength of 10 V/m is achieved in the experiments. Combining the wavelength tuning technique, the thermal variations in the sensor bias have fallen from around 120 degrees down to be 2 degrees with the temperature ranging from 24°C to 70°C. These results are very encouraging toward the development of integrated optical electric field sensing systems in the practical applications.
Satellite communication is an important part of the information communication network. Strong electromagnetic impulse may enter the RF reception channel of the satellite communication receiving system of the same frequency band, and bring damage to sensitive components such as the limiter, low-noise high frequency amplifier, thereby causing loss of the function of the satellite communication system. In this paper a behavior-level simulation model of typical satellite communication equipment is established, and an analysis on the influence to the communication performance after the limiter is damaged by strong electromagnetic impulse is conducted. The simulation results show that, apart from the variation of the noise factor at the RF front-end of the satellite communication receiver caused by insertion loss variation of the limiter, the bit error rate is also influenced by the gain control method and modulation method.
With the advent of 5G, wireless communication has greatly changed people's lifestyles. However, limited by the coverage of terrestrial cellular networks, the demand for communication services of mobile phones in remote areas is difficult to be met. In order to meet the large coverage and quality of service (QoS) requirements of mobile phones, we consider a non-orthogonal multiple access (NOMA)-based mobile phones and internet of things (IoT) fusion satellite network. In this network, low earth orbit (LEO) satellite can significantly enlarge the coverage while NOMA and IoT further improve the utilization efficiency of resources. Aiming at maximizing the QoS satisfaction rate of mobile phones and the sum rate of internet of things devices, we formulate a joint optimization problem considering NOMA user grouping, inter-group power allocation and intra-group power allocation. To tackle the problem, we design a QoS priority joint optimization algorithm based on proximal policy optimization (Q-PPO). The experimental results show that the proposed Q-PPO algorithm always has considerable performance in QoS satisfaction rate and sum rate of internet of things devices.