Ingomar Kelbassa

Ingomar Kelbassa

Auto-generated profile, based on publicly available information

Ingomar Kelbassa

Fraunhofer Research Institution for Additive Manufacturing Technologies IAPT Hamburg Germany

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 August 2026 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Open access
SMSebastian Mansky
Sebastian Mansky
DHDirk Herzog
Dirk Herzog
IKIngomar Kelbassa
Ingomar Kelbassa
This paper investigates the fatigue behavior of additively manufactured TiAl6V4 by comparing two specimen geometries with different highly stressed volumes. A fracture mechanical approach based on the El‐Haddad–Smith–Topper model is combined with defect analysis through X‐ray computed tomography. A combined generalized extreme value and generalized Pareto distribution framework correlates defect size distributions with failure probability across all stress levels. Results show that larger highly stressed volumes increase failure susceptibility due to higher likelihood of critical defects, reducing the fatigue stress range at 50% failure probability from 882 to 611MPa. For topology‐optimized parts, components with localized stress concentrations are less susceptible to defects than those with homogeneous stress distributions. The highly stressed volume approach can yield misleading results for such geometries. The methodology enables transfer of laboratory results to components by integrating stress states, defect statistics, and volume effects.

29 August 2026 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Open access
SMSebastian Mansky
Sebastian Mansky
DHDirk Herzog
Dirk Herzog
IKIngomar Kelbassa
Ingomar Kelbassa

26 May 2026 in Powder Metallurgy
Verified
Journal Article
Open access
KBKatharina Bartsch
Katharina Bartsch
DHDirk Herzog
Dirk Herzog
LWLennart Waalkes
Lennart Waalkes
KJKevin Janzen
Kevin Janzen
SGStefan Grottker
Stefan Grottker
JGJohannes Gårdstam
Johannes Gårdstam
Piston-based material extrusion (PEX) is an additive manufacturing technology that enables the processing of metal injection moulding (MIM) feedstock to form green parts. The extrusion process does not require moulds and hence is a competitive alternative for the shaping of MIM process routes, offering short lead times and cost-efficiency for lower lot sizes, while integrating into the remaining process chain and equipment. This paper focuses on the microstructure and properties of Ti-6Al-4V fabricated by PEX and followed by a subsequent hot isostatic pressing (HIP) step for parts requiring superior density and mechanical properties. The HIP process is performed using standard as well as high-purity conditions (Quintus Purus ® ). After sintering, a globular, mostly α microstructure is observed. A subsequent HIP followed by rapid quenching transforms the microstructure to a bi-modal state. A similar effect on microstructure is observed for the Quintus Purus ® HIP; however, the formation of α-case on the part surface is avoided. While the mean density of the sintered parts is 97.2%, HIP leads to an increase to 98.9–99.3% with the remnant porosity mainly stemming from open, connected pores. Although the sintered specimens already fulfil the industrial requirements, the Quintus Purus ® HIP leads to a slight increase in yield and ultimate tensile strength at minimal reduction of elongation. The standard HIP shows the same but slightly more pronounced trend. The results show that by a careful design of the specific HIP conditions, the microstructure and properties can be tailored for a specific application.

8 October 2025 in Journal of Laser Applications
Verified
Journal Article
Closed access
JHJan Hünting
Jan Hünting
KAKarim Asami
Karim Asami
SLStella Lo
Stella Lo
IKIngomar Kelbassa
Ingomar Kelbassa
CEClaus Emmelmann
Claus Emmelmann
Multimaterial additive manufacturing enables the integration of different materials within a single component, allowing for tailored functionality and the reduction of process steps. Among available metal additive manufacturing (AM) techniques, material extrusion of metals (MEX/M) offers a cost-effective and feasible approach for the production of multimaterial parts using a commercial feedstock. This study focuses on the fabrication of green parts composed of pure copper (Cu) and Inconel 718 (IN718), selected for their highly complementary properties: Cu offers excellent thermal conductivity, while IN718 provides outstanding mechanical strength, as well as high corrosion and oxidation resistance. These characteristics make the Cu-IN718 combination particularly attractive for demanding aerospace applications, such as heat exchangers and combustion chambers. A design of experiments approach using response surface methodology was employed to evaluate the influence of key printing parameters, such as nozzle temperature, printing speed, extrusion multiplier, and layer thickness, on the density and dimensional accuracy of green part test specimens. Optimal process parameter sets for each individual material were identified and a corresponding parameter set for the multimaterial combination was subsequently derived. Different geometric features, various material topologies, and two interlocking geometries were analyzed to assess the print quality and geometric accuracy of multimaterial prints. The results were used to derive a set of design guidelines aimed at the manufacturability, reliability, and quality of Cu-IN718 green parts using MEX/M. These guidelines contribute to future standardization efforts in multimaterial extrusion, thus supporting more robust and reproducible production of components via metal AM.

1 May 2026
Verified
Book Chapter
Closed access
PSPhilipp Sauberzweig
Philipp Sauberzweig
VPVishnuu Jothi Prakash
Vishnuu Jothi Prakash
IKIngomar Kelbassa
Ingomar Kelbassa
ASArthur Seibel
Arthur Seibel
JMJacob Mätje
Jacob Mätje
MBMilan Brandt
Milan Brandt