The multiport dc-ac converter (MPC) connected to photovoltaic (PV)-battery hybrid system has the characteristics of high efficiency and low cost in single stage power conversion. However, it is challenging to achieve common-mode voltage (CMV) reduction in this configuration due to its need for power distribution through redundant vectors. To overcome this limitation, this paper proposes an improved space vector modulation (ISVM) method to reduce the CMV and achieve flexible power distribution. By selecting vectors with lower CMVs, a set of new virtual voltage vectors based on the power control parameter is generated. In addition, to further realize flexible power distribution among PV, battery and load, a new control scheme is proposed to achieve power balance in different operating modes under CMV reduction. The highlight of the method is its ability to achieve power distribution and lower CMV simultaneously. Finally, compared to conventional methods, the simulated and experimental results prove that the proposed method can realize CMV reduction, flexible power control with variable port voltages.
10 January 2025 in IEEE Transactions on Power Electronics
Since the high efficiency and low cost of single-stage power conversion, dual-dc-port dc-ac converters have been used in photovoltaic (PV)-battery hybrid systems. However, achieving leakage current suppression in this configuration is challenging due to its coupling characteristics in terms of common mode voltage (CMV) reduction and power distribution. To deal with this issue, a method using unbalanced large, medium, small vector modulation (ULMSVM) with CMV transition reduction is proposed in this paper. Firstly, the CMV of voltage vectors is calculated and sorted under different voltage conditions. Then, for the purpose to reduce CMV transition, the switching interval between vectors is at most one vector in a switching sequence according to sorting relations. In addition, high CMV small vector sequences and medium vector sequences can be used as independent power control sequences to help achieving battery charging and discharging. Finally, to realize flexible power regulation, a new power control scheme is proposed to balance the PV power fluctuation by the battery power exchanged, which can provide the discharge/charge sequences with different control capabilities. The effectiveness of the proposed method is verified by the experiment at the end of the paper.
20 October 2025 in IEEE Transactions on Power Electronics
In LCL-filtered inverters under weak grid conditions, the point of common coupling (PCC) voltage feedforward has been applied to mitigate the current harmonics caused by background harmonics in the PCC voltage. However, due to the control delay of the digital controller, the system stability is significantly reduced. Moreover, since the grid impedance cannot be sensed in practice, conventional model-based advanced prediction techniques fail to provide delay compensation anymore. To overcome these limitations, a high-accuracy local model independent of the grid impedance, instead of the overall system model, is established, and a novel PCC voltage feedforward with delay compensation is presented. First, the best placement of the delay compensator is investigated, which concludes that the PCC voltage feedforward compensation can achieve the best delay compensation effect. Then, based on the established model, the PCC voltage is calculated and predicted for one sampling period in advance. Thus, the control delay in the PCC voltage feedforward loop is compensated, and the system stability is significantly improved under weak grid conditions. Finally, the effectiveness of the proposed scheme is verified by experiments.
4 August 2025 in IEEE Transactions on Industrial Electronics
Multiport dc–ac converter has gained attention due to its power density and low cost. However, in virtual space vector pulse width modulation (VSVPWM) where common-mode voltage (CMV) reduction and power control are considered, there are multiple switching actions in a period, which can be called multiswitch-VSVPWM (MS-VSVPWM). This leads to complex vector synthesis rules, and dead-time effect (DTE) needs to be analyzed due to variable port voltages. To simplify computation, a carrier-based MS-VSVPWM with DTE elimination is proposed. First, according to volt-second balance and dwell time relations, variable and fixed modulation waves are derived. Then, final output sequences are obtained by using phase opposition disposition (POD) carrier. Second, shifted modulation wave is derived on this basis. The drive signals are obtained by the variable/fixed modulation wave and the shifted modulation wave, respectively. Thus, DTE is eliminated on the premise of avoiding shoot-through of power switches. In addition, a variable shift value strategy is investigated to obtain the maximum shift value. Finally, the proposed method is verified experimentally on photovoltaic (PV)-battery hybrid system prototype, showing its high efficiency and relatively low output harmonics based on CMV reduction and power control.
25 November 2025 in IEEE Transactions on Power Electronics
Multilevel converters are widely used in various industrial applications. One of the critical challenges in these systems is the suppression of common-mode voltage (CMV). Due to the intuitive nature of the space vector diagram, space vector pulsewidth modulation (SVPWM) can effectively regulate CMV. However, as the number of voltage levels in multilevel converters increases, the complexity of the SVPWM method also grows. Existing simplified SVPWM techniques, which are helpful, have not been fully successful in suppressing the CMV. To address the above issues, this article proposes a generic SVPWM (GSVPWM) method. Unlike conventional approaches, the GSVPWM is based on the natural abc coordinate system, eliminating the need for coordinate transformations. In addition to effectively suppressing both the magnitude and frequency of the CMV, the GSVPWM further reduces the dv/dt values of the CMV by subdividing the equilateral triangular sectors into obtuse triangular sectors. The proposed method operates in real-time, without requiring look-up tables or complex calculations. It is easy to implement across different multilevel converters. Simulations and experiments are conducted in a five-level converter to verify the effectiveness of the proposed GSVPWM.
1 January 2026 in IEEE Transactions on Industrial Electronics