29 September 2023 in IEEE Transactions on Power Electronics
DC/DC converter is widely used in power electronic applications as a critical part of power supply. During operation, component parameters of the DC/DC converter gradually degrade subjected to various environmental stresses. When they degrade to deviate from the normal value, soft faults will occur and directly affect the functionality and reliability of the whole system. To identify these anomalies effectively, a novel soft fault detection and diagnosis method based on contrastive learning is proposed for a DC/DC Buck converter. First, the output voltage ripples of the converter under healthy and faulty conditions are collected. Then, a feature representation of the voltage ripple is obtained through hierarchical contrastive learning at temporal-level and instance-level. Based on the learned representation, a support vector machine classifier is established to detect and locate soft faults. The proposed method does not need extra hardware or signal injection, thereby reducing the cost and complexity. Simulation and physical experiment results verify the effectiveness and robustness of the proposed method.
18 March 2024 in IEEE Transactions on Industrial Electronics
With the increasing demand for ocean missions, the development of autonomous marine vehicles (AMVs) has flourished. AMVs rely on electricity to power various systems, so the high reliability and stability of dc-dc converters are critical to the normal operation of AMVs. In reality, fault diagnosis and optimization of converters under the low sampling frequency and computational capability conditions remain practical challenges. This article focuses on the buck converter circuit and utilizes undersampling techniques to obtain output voltage signals sampled at a low sampling frequency. Support vector machine recursive feature elimination is employed for feature selection to reduce computation. Bayesian optimization-based extreme learning machine is used for fault diagnosis, which is suitable for actual deployment and shown to outperform three classical machine learning models. The diagnosis results are used to propose a reliability optimization strategy involving switching frequency adjustment. Physical experiments based on a digital signal processor prove the feasibility of this method.
11 July 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
As critical components in power electronic systems for energy conversion and power management, DC/DC converters are commonly employed in aerospace, electric vehicles, and other electronic devices. Their degradation may lead to instability failure of the power electronic system, significantly impacting the reliability of devices. To prevent irreversible damage, various degradation detection methods have been proposed, which have advantages such as automatic, real-time, accurate, and non-invasive. However, few studies have considered effective degradation detection with reduced resource demands and sampling costs. In this paper, a signal reconstruction technique is adopted in signal acquisition and a novel early degradation detection method is proposed for the output filter capacitor and energy storage inductor of a DC/DC buck converter. In the proposed method, degradation features are extracted from output voltage ripples through long short-term memory fully convolutional network and contrastive learning. Based on the learned features of normal and degraded samples, the converter degradation state is identified. To enhance robustness against noise, the Mixup-based data augmentation is applied to increase data diversity. The effectiveness of the proposed method is verified by simulation and experiment.
8 April 2020 in IEEE Access
In traditional motor drive system, large volume electrolytic capacitors are utilized to buffer energy and stabilize the dc-link voltage. However, these capacitors affect the reliability of the drives and narrow the conduction angle of diode-rectifier. As a result, the grid side current is distorted and the power factor is deteriorated. In order to settle these issues, small dc-link capacitors can replace the electrolytic capacitors. In this paper, a motor torque control method with dc-link voltage feed-forward compensation for an interior permanent magnet synchronous motor (IPMSM) drive system is proposed. Hence, an integration multi-resonant (I-MR) controller is established to regulate the motor torque to obtain high input power factor and low grid current harmonics. In addition, a voltage feed-forward compensation is used to diminish the error of motor torque control. The effectiveness of the proposed method is verified through simulation and experiments. Results indicate that the input power factor can reach about 99.4% and the grid current harmonics are considerably lower than the requirement of EN-61000-3-2 standard.
20 September 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Film capacitors are used in power electronic converters due to their higher reliability compared to aluminum electrolytic capacitors. Humidity is one of the critical factors affecting the aging of film capacitors. However, the existing methodologies for lifetime estimation of film capacitors rarely consider humidity. Besides, sometimes it is hard to obtain a large amount of data in the accelerated aging test of the device. To solve these problems, this paper proposes a lifetime estimation methodology that requires less data and testing time. In the proposed methodology, humidity dummy variables are introduced into the degradation model based on the multivariate linear regression (MLR) algorithm. The impact of introduced dummy variables with different structures on the degradation model is studied and the effect of the proposed lifetime estimation method is verified. The results show that the proposed scheme achieves a comparable performance and can be valid in reality.
9 September 2025 in IEEE Transactions on Power Electronics
DC/DC converters play a crucial role in electronic systems by providing the necessary power support and ensuring the proper operation of devices. During operation, the converter is exposed to environmental factors, such as temperature and humidity, leading to component degradation and subsequently posing a threat to system reliability and functionality. This arrticle presents an effective degradation detection method for dc/dc converters using feature extraction techniques. The output voltage ripple is used as the degradation indicator, and its values under healthy and degradation conditions are collected. Based on the time domain, frequency domain, and time-frequency domain feature information of the output voltage ripple, a valid feature selection method is designed to select key features, and the Bayesian optimization-based support vector machine is established to detect degradation using the selected key features. Since no extra hardware circuits or elaborate mathematical models are required, the proposed method has low cost and complexity. Simulation and experimental results show the validity and practicability of the proposed method.