30 April 2018 in IEEE Transactions on Electron Devices
In this brief, the monolithic integration of enhancement (E)-mode and depletion (D)-mode InAlN/GaN high-electron mobility transistors (HEMTs) is presented. The aim of this brief is to show the results of the designed NAND logic cell, which consists of both HEMTs integrated onto a single die. Large-signal models of dual-gate E-mode and D-mode HEMTs are proposed and calibrated by experimental results. We present well-calibrated electrophysical models for 2-D device simulations employing mixed-mode setup in Synopsys TCAD Sentaurus device. The mixed-mode approach interconnects dual-gate E-HEMT and D-HEMT to NAND logic cell circuit, which allows analysis and characterization of the device as the complex system. Good agreement between simulations and experimental results confirms the validity of the proposed models and simulation methodology.
23 March 2021 in IEEE Transactions on Electron Devices
Vertical current conduction in a 1.3- μm-thick semi-insulating (SI) C-doped GaN grown on a GaN substrate is analyzed. During the growth, pressure was varied from 100 to 20 mbar in order to increase C concentration from ~ 1×10 17 cm -3 to ~ 6×10 18 cm -3 ; SI GaN is sandwiched between two n-GaN layers. Optical transitions suggest two acceptor levels: ~0.9 eV above the valence band and ~0.6 eV below the conduction band. Current-voltage characterizations reveal a space-charge-limited-current conduction with an impact-ionization-assisted filling of traps in a moderately C-doped sample. On the other hand, highly compensated SI GaN forms a ~0.5-eV potential barrier at the interface with n-GaN, whereas the breakdown voltage exceeds 350 V. As the model explains, deep acceptors above the valence band compensate residual donors and lead to an electron mobility collapse. On the other hand, depending on C concentration, acceptors below the conduction band play a different role. In the moderately doped SI GaN, they act as electron traps and define the breakdown voltage. On the other hand, acceptors below the conduction band in highly compensated SI GaN are responsible for the barrier-controlled conduction and reaching of the avalanche.
9 December 2020 in IEEE Transactions on Electron Devices
The mapping of the current induced by a focused electron beam in a scanning electron microscope (SEM) has been used to localize electrically stressed regions in the AlGaN/GaN-on-Si Schottky barrier diode (SBD) structures cross-sectioned by the focused ion beam (FIB) technique. We have shown that homogeneously distributed electron beam induced current (EBIC) intensity detected below the Schottky contact at 0 V changes with increasing reverse voltage V R and peaks at the edges of a field-plate region. The build-up of local microavalanches at high electric voltages has been indicated by overexposed EBIC signal at areas following the edges of the field plate structure. Interpretation of EBIC measurements is supported by electro-physical modeling and simulations employing the 2-D finite element method in Synopsys TCAD Sentaurus. The simulations prove that the electric field intensity in the SBD locally reaches values sufficiently high to trigger multiplication of the excessive carriers generated by an electron beam, which helps one to visualize and localize critical regions in GaN-based power electronic devices by the EBIC method.
24 November 2025 in Journal of Electronic Materials
We present the results of electron-beam-induced current (EBIC) measurements using a Schottky nanocontact formed by a tungsten needle placed on an intentionally undoped GaN layer grown by metalorganic chemical vapor deposition (MOCVD) on a sapphire substrate. The EBIC line profiles, extracted from the EBIC maps recorded in the vicinity of the contact, are used to identify key sources of uncertainty in estimating the minority charge carrier diffusion length in GaN. To complement the experimental analysis, a three-dimensional Monte Carlo (MC) model of charge carrier generation, diffusion, and EBIC formation is adopted and further developed to quantitatively investigate the evolution of EBIC line profiles at Schottky nanocontacts under varying sample and electron beam (e-beam) parameters. The simulations reveal that, for materials with short diffusion lengths such as GaN, the shape of EBIC line profiles at the space charge region (SCR) perimeter is significantly affected by the shape of the contact formed by the needle and e-beam energy. The findings highlight the limitations of the conventional EBIC-based diffusion length extraction method in materials with short diffusion lengths and support the advancement of EBIC methodologies for nanoscale Schottky contacts.