8 November 2021 in Journal of Nanomaterials
The diamond-like carbon- (DLC-) coating technique is used in the sliding parts of automotive engines, among other applications, to reduce friction and wear. In this work, DLC has been coated on the Aluminium 5051 sample to assess the mechanical and tribological properties. A sputtering deposition mechanism is used, and the DLC is coated using a graphite target. The developed DLC coatings are tested for adhesion strength, hardness, chemical composition using XRD, and wear behaviour. The developed DLC thin films have considerably increased the wear behaviour of the Aluminium 5051 sample and have fulfilled the objective of this study. The XRD data indicated the presence of amorphous carbon in the coating with a threefold increase to the hardness of the naked aluminium. This study provides insight into improving the aluminium wear resistance by developing a considerably hard coating.
13 January 2022 in Advances in Materials Science and Engineering
Biomass energy accounts for more than 92 percent of overall energy consumption in Ethiopia. As a result, Ethiopia is one of the worlds most biomass-dependent countries. The high reliance on wood fuels and agricultural residues for fuel harms societys social, economic, and environmental well-being. This study aims to create and test the quality of fuel briquettes made from the coffee husk. Also built and produced are a carboniser/charcoal kiln, a manually operated molder system, and a briquette stove for burning the manufactured briquette. The carboniser converts 15kg of raw coffee husk into 6kg of carbonised char in 25minutes, and the manually operated briquette molder can press 30kg per hour. The efficiency of converting raw coffee husk into carbonised char content was 40.12. In the geological survey of Ethiopia, the geochemical laboratory directorate received triplicate samples of the fuel briquette charcoal for analysis. Moisture content, fixed carbon content, ash content, sulfur content, and calorific value were determined using a bomb calorimeter and a ceramic lining furnace. Physical properties of fuel briquettes ranged from 10.03 moisture content, 970kg/m3 density, 81 fixed carbon, 5.15 ash content, 0 sulfur, and 30.54Kcal/kg higher heating value, according to laboratory results. The results of the study revealed that the coffee husk fuel briquettes produced have more positive characteristics. Fuel briquettes were cost-effective and environmentally friendly and reduced deforestation compared to firewood. This study clearly shows that briquettes made from coffee husk could be used as an alternative energy source when this kind of waste is well managed.
31 October 2021 in Journal of Nanomaterials
In this article, the photovoltaic thermal collector (PVT) have designed and fabricated using nanoparticle nanofluid. The cause of this is to check out the effect of using water and water-based totally graphene nanoplatelets at an awareness of 0.05 wt% on the performance of PVT structures. Outdoor assessments have been performed at quantity along with the float prices of 0.5 L/min and 1.0 L/min for the aforementioned nanofluids, respectively, using water as a reference fluid. The results that have been analyzed from an active angle confirmed and determined that, graphene water nanofluid achieved higher in phrases of photovoltaic active conversion, than water that might generate the first-class thermal performance sooner or later of the peak period of sun radiation and high mobile temperature. The inclusion of water in the PVT collector increases average daily electrical efficiency by 7.8%, and 8.5%at flow rates of 0.5 LPM and 1.0 LPM, respectively. Furthermore, using water in the PVT collector increases average daily thermal efficiency by 24.9%, and 26.3%at flow rates of 0.5 LPM and 1.0 LPM, respectively.
20 February 2023 in Journal of Nanomaterials
This research focused to synthesize the material by the tungsten inert gas (TIG) welding process with support of appropriate flux coating material. Therefore the required amount of flux coating material was utilized to enhance the mechanical properties of the specified localized welded regions. Hence, this study concentrated to select the nano-SiO2 flux particles that were employed for TIG process. This activated TIG welding composes the flux-coated welding on the base metal of AA5083-H111, as this material was highly reactive with SiO2 by the presence of magnesium precipitates and well synthesized after the welding. The post- and preheat treatment process was achieved before and after welding. The selection of activated TIG process parameters composed of strengthened weld specimens along with constant parameters like electrode tip angle and flow rate, respectively. Initially, the process parameters were designed by the statistical analysis of Box Behnken method with support of regression formulation to determine the optimal solution. The maximum tensile strength was attained at the welding process parameters of welding speed (100mm/min), voltage (13V), and current (125amps). The higher hardness was achieved at the process parameters of welding speed (80mm/min), voltage (12V), and current (125amps), respectively. Finally, the neural network approach was utilized to verify the predicted responses of tensile and microhardness properties. The interaction plots, mean plots, and 3D scatter plots were influenced to enhance the process parameters. In this research, mechanical properties were enhanced by the flux-coated SiO2 and the analytical method also advances the optimal parameters.