In this paper, we propose an ultra-low power compact 3-transistor voltage reference capable of operating at ultra-low supply voltages. The proposed circuit is based on the self-cascode MOSFET (SCM), which provides a reference voltage proportional to the threshold voltage (VT) difference of the two NMOS transistors that compose it. Reverse short-channel and narrow-width effects are explored to obtain such VT difference while using the same type of transistor. Ultra-low power operation and low line sensitivity is achieved by biasing the SCM with a zero-VT (native) transistor, also leading to an area efficient design. To show its versatility, three versions of the proposed circuit were fabricated in a standard 0.13-μm CMOS process. Measurement performed over five samples showed an average temperature coefficient of 150-1500 ppm/°C. Minimum supply voltages of 0.12-0.4 V was observed while providing reference voltages around tens of mV. The proposed circuits consume 0.33-50 pW at room temperature and minimum supply voltage. The occupied area for any version is less than 0.0012 mm2.
This paper presents the operation principle and the silicon characterization of a power efficient ultra-low voltage and ultra-low area fully-differential, digital-based Operational Transconductance Amplifier (OTA), suitable for microscale biosensing applications (BioDIGOTA). Measured results in 180nm CMOS prototypes show that the proposed BioDIGOTA is able to work with a supply voltage down to 400 mV, consuming only 95 nW. Owing to its intrinsically highly-digital feature, the BioDIGOTA layout occupies only 0.022 mm 2 of total silicon area, lowering the area by $3.22\times $ times compared to the current state of the art, while keeping reasonable system performance, such as 7.6 NEF with $1.25~\mu V_{\mathrm {RMS}}$ input referred noise over a 10 Hz bandwidth, 1.8% of THD, 62 dB of CMRR and 55 dB of PSRR.
27 May 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
An ultra-low voltage and ultra-low power Digital-Based Operational Transconductance Amplifier (DB-OTA) is presented and demonstrated on silicon in 180 nm CMOS. The DB-OTA is designed using digital standard cells, hence benefitting from technology scaling as much as digital circuits, while also being technology- and design-portable, and requiring minimal design and integration effort compared to conventional analog-intensive OTAs. The fabricated DB-OTA testchip occupies a compact area of 1,426 μm 2 , operates at supply voltages down to 300 mV, and consumes only 590 pW while driving a capacitive load of 80pF. Its measured Total Harmonic Distortion (THD) is lower than 5% at a 100-mV input signal swing. Based on these results, the proposed DB-OTA achieves 2,101 V -1 small-signal figure of merit (FOM S ) and 1,070 large-signal figure of merit (FOM L ). To the best of the authors' knowledge, the power is the lowest reported to date in an OTA, and the achieved figures of merit are the best in sub-500 mV OTAs reported to date. The low cost, the low design effort and the high power efficiency of DB-OTA make it well suited for purely harvested low-frequency analog interfaces in sensor nodes.
The calibration of the effects of process variations and device mismatch in Ultra Low Voltage (ULV) Digital-Based Operational Transconductance Amplifiers (DB-OTAs) is addressed in this paper. For this purpose, two dynamic calibration techniques, intended to dynamically vary the effective strength of critical gates by different modulation strategies, i.e., Digital Pulse Width Modulation (DPWM) and Dyadic Digital Pulse Modulation (DDPM), are explored and compared to classic static calibration. The effectiveness of the calibration approaches as a mean to recover acceptable performance in non-functional samples is verified by Monte-Carlo (MC) post-layout simulations performed on a 300 mV power supply, nW-power DB-OTA in 180 nm CMOS. Based on the same MC post-layout simulations, the impact of each calibration strategy on silicon area, power consumption, and OTA performance is discussed.
1 August 2015 in Journal of Integrated Circuits and Systems
In this paper a self-biased current reference based on Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) Zero Temperature Coefficient (ZTC) condition is proposed. It can be implemented in any Complementary Metal-Oxide-Semiconductor (CMOS) fabrication process and provides another alternative to design current references. In order to support the circuit design, ZTC condition is analyzed using a MOSFET model that is continuous from weak to strong inversion, showing that this condition always occurs from moderate to strong inversion in any CMOS process. The proposed topology was designed in a 180 nm process, operates with a supply voltage from 1.4V to 1.8 V and occupies around 0.010mm2 of silicon area. From circuit simulations our reference showed a temperature coefficient (TC) of 15 ppm/oC from -40 to +85oC, and a fabrication process sensitivity of σ/μ = 4.5% for the current reference, including average process and local mismatch variability analysis. The simulated power supply sensitivity is estimated around 1%/V.
23 June 2015 in Analog Integrated Circuits and Signal Processing