27 September 2022 in IEEE Microwave and Wireless Technology Letters
In this letter, a K -band high-efficiency power amplifier (PA) design using modified resistive-reactive hybrid continuous modes (HCMs) is presented. These modified modes can increase the real part of the fundamental impedance when the second harmonic impedances become resistive-reactive. This helps to reduce the impedance transformation ratio when applying modified modes in transistors with a small optimal impedance ( R $_{\mathbf{opt}}$ ), as well as making HCMs more practical in these transistors. For K -band Satcom downlink applications, by using this method, combined with a compact output matching network (OMN) design, high performance, and high integration PA can be achieved. A 2 $\times$ 1.2 mm GaAs pHEMT PA operating at 17–24 GHz was designed and fabricated to verify the theory. Continuous wave measurements show that the saturation output power is greater than 0.5 W and an average power-added efficiency (PAE) of 42%.
5 August 2022 in IEEE Transactions on Instrumentation and Measurement
This article presents a broadband amplifier for high-speed modulators and measurement driver circuits using distributed amplifiers (DAs) configuration. The flat low-frequency performance of the conventional DAs is limited by termination impedance. This article shows that on- chip low-frequency extension can be achieved by optimizing the capacitively coupled circuit and impedance termination. Although capacitively coupled circuit has been introduced in previous studies to extend the high-frequency gain, sufficient analysis has not been studied. Furthermore, a novel broadband equalizer termination applying for distributed configuration is introduced, which can be employed to balance the rising gain. This DA features the lowest cutoff frequency among broadband amplifiers using the on- chip circuit. The amplifier provides a comparable low-frequency performance of megahertz (MHz) with greater than 15-dB gain and benchmarks the first demonstration of a flat MHz performance monolithic microwave integrated circuit (MMIC) using on- chip passive components. The proposed amplifier achieves a 17-dBm output 1-dB compression point (OP1dB) covering eight-octave bandwidth verified using a 0.15- $\mu \text{m}$ GaAs pseudomorphic high-electron-mobility transistor (pHEMT) technology. The new design architecture combined with the broadband equalizer characteristics and gate series network can provide performance benefits for optic modulators, instrumentations, and advanced broadband transmitters.
10 May 2024 in IEEE Transactions on Electromagnetic Compatibility
With the wide application of high-sensitivity broadband microwave receivers, the requirement of power-supply modulation ratio in receivers is greatly increased. Especially, the switched mode power-supply harmonics of the secondary converted power-supply in the satellite will inevitably produce spurious emissions in the receiver band. Therefore, it is necessary to analyze and prejudge the spurious response rejection ratio of the entire link from power-supply when designing a spaceborne high-sensitivity broadband receiver. The systematic theoretical formula of the spurious rejection ratio of each link is obtained by researching the influence of circuit design parameters, including the ratio of modules’ area to spacing, transistor bias voltage, frequency multiplying times, and sensitivity of the voltage-controlled oscillator. Taking a spaceborne Ka-band broadband receiver as an example, and the actual receiver is manufactured and measured for verification. By reducing the circuit area to 35 cm 2 , separating the module spacing to 0.1 mm, selecting a transistor gate bias voltage of −0.25 V, increasing the oscillator frequency to 3.25 GHz, and reducing the oscillator's voltage control sensitivity to 58 MHz/V, the optimal power supply switched spurious rejection ratio of nearly 60 dBc was ultimately achieved.
1 June 2025 in The Leading Edge
Electrical properties of reservoirs are often used to infer hydrocarbon saturation using log-based reservoir evaluation tools. The presence of clay minerals in shaly sands leads to an apparent increased electrical conductivity that needs to be properly modeled to obtain accurate hydrocarbon saturation. The Waxman-Smits equation is one commonly used model for evaluating clay-bearing shaly sands. Traditionally, Waxman-Smits equation parameters m* and Qv are obtained by saturating a core plug with brines of different salinity and measuring the effective conductivity as part of special core analysis. In this work we present a novel method of estimating the impact of clay conductivity on the electrical properties of shaly sands using digital rock physics (DRP). By imaging the rock using micro-CT technology and simulating the response of effective conductivity using variable brine salinities, Waxman-Smits parameters m* and Qv may be estimated. Such a workflow has the potential to significantly accelerate reservoir evaluation workflow and data delivery by imaging the rock without solvent cleaning and simulating multiple salinities and samples in parallel. As examples, we applied the DRP workflow to three sandstone outcrop samples. We propose a potential application of the DRP workflow for reservoir modeling using information from available log data. The assumptions made in the workflow and the resulting uncertainties are also discussed.