A.S. Sauffi

A.S. Sauffi

Auto-generated profile, based on publicly available information

A.S. Sauffi

Universiti Malaysia Perlis (UniMAP), Faculty of Chemical and Engineering Technology, 01000 Perlis,Center of Excellence Geopolymer and Green Technology (CEGeoGTech), Malaysia

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 September 2023 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
WIWan Mastura Wan Ibrahim
Wan Mastura Wan Ibrahim
MIMasdiyana Ibrahim
Masdiyana Ibrahim
MAM.Z.A. Azis
M.Z.A. Azis
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
ASA.S. Sauffi
A.S. Sauffi
SASuraya Hani Adnan
Suraya Hani Adnan
Due to their potential to lower CO2 emissions linked with the cement and concrete industries, geopolymer binders are a desirable alternative for Portland cement binders. However, if they are to become a viable alternative to conventional Portland cement materials, their resilience in harsh conditions has to be further investigated. This paper presented mechanical and short-term durability properties of metakaolin based geopolymer concrete at sulphuric acid (H2SO4) solutions exposed with the concentrations of 2%, 3%, 4% and 5% for 14 days. (0%) or unexposed sample also prepared as referral and comparison. The geopolymer concretes were synthesized using an alkali activation of sodium hydroxide (NaOH) and sodium silicate (Na2SiO3). The main objective of the study was to examine the durability and deterioration mechanism parameters like different acid percentages, changes in weight, compressive strength, density and water absorption. Morphology analysis also performed in this study. The results indicated that metakaolin geopolymer experienced some strength deterioration with increasing sulphuric concentration solutions which are from 32.58 MPa, 20.67 MPa and 4.25 MPa at unexposed (0%), 2% and 5% sulphuric acid immersion respectively. Furthermore, change in weight or mass loss and water absorption after the chemical attack resulted directly proportional to sulphuric acid concentration due to increment of crack on the sample. Among that, the metakaolin geopolymer submerged in 2% acid gives the optimum results in terms of durability, mechanical and physical qualities.

16 December 2024 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
FZF.H.A. Zaidi
F.H.A. Zaidi
Suhani AhmadSuhani Ahmad
Suhani Ahmad
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
WIWan Mastura Wan Ibrahim
Wan Mastura Wan Ibrahim
MBM.I.A. Bistamam
M.I.A. Bistamam
LLLong-yuan Li
Long-yuan Li
Geopolymer concrete is a new sustainable and environmentally friendly composite with great potential to replace conventional concrete that is mostly produced by ordinary Portland cement (OPC). Binders used for geopolymer concrete such as fly ash and blast furnaces are mostly industrial wastes or by -products containing high silica and aluminium content that act as stimulants for geopolymerization. Furthermore, geopolymers also exhibit better durability and corrosion resistance than OPCs. However, material subjected to underwater placement method typically exhibit a decrease in properties. While geopolymer has not been widely used as underwater concreting material, this research is purposed to identify the effect of underwater placement method towards geopolymer in terms of microstructure analysis. Using different molarities of sodium hydroxide (NaOH), the optimum compressive strength will be discussed for underwater concrete while correlating with the microstructure result. For alkaline activators, the ratio used is 2.5 and the ratio for solid to liquid is 2.5. The molarities used for alkaline activators were 8 M, 10 M and 12 M. Using the tremie method for underwater concrete, it is possible to measure the leaching loss with respect to the objective of this research. The best compressive strength result is 12 M. The SEM result support with 12 M molarity had less cavities and lowest density.

16 December 2024 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
ASA.S. Sauffi
A.S. Sauffi
WIWan Mastura Wan Ibrahim
Wan Mastura Wan Ibrahim
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
MIMasdiyana Ibrahim
Masdiyana Ibrahim
Suhani AhmadSuhani Ahmad
Suhani Ahmad
FZF.A. Zaidi
F.A. Zaidi
This paper presents the morphology of the metakaolin/dolomite geopolymer after being exposed to high temperature and compare the findings with the morphology that has not been exposed to the temperature. The geopolymers were exposed at temperatures from 200°C up to 800°C. The geopolymer was a constant mix of 90% metakaolin and 10% dolomite with 10 NaOH molarity, 0.8 solid to liquid ratio, and 2.0 by mass of alkaline activator. The morphology of geopolymer exposed to high temperature contains many pores and as the temperature rises, the pores become huge, and a higher quantity of pores can be observed. The surface analysis, compressive strength, and water absorption test were also done to support the findings. The compressive strength calculation was based on weight loss. The lowest compressive strength loss was at 200°C temperature exposure with 10.98%. Meanwhile, the highest compressive strength loss was at 800°C temperature exposure with 48.54%. In comparison, this metakaolin/dolomite geopolymer archive better properties compared to the concrete and metakaolin past studies.

16 December 2024 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
MIMasdiyana Ibrahim
Masdiyana Ibrahim
WIWan Mastura Wan Ibrahim
Wan Mastura Wan Ibrahim
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
ASA.S. Sauffi
A.S. Sauffi
Suhani AhmadSuhani Ahmad
Suhani Ahmad
The presence of nickel ions in wastewater is a significant environmental concern due to its toxicity, which can cause severe health problems. Metakaolin is a pozzolanic material that can be activated by alkali to produce a highly porous and reactive material that can be utilised as a heavy metal ion adsorbent. However, the adsorption capacity of metakaolin-based adsorbents is limited by their surface chemistry and porosity. Metakaolin-based alkali-activated materials adsorbent modified with hydrogen peroxide can effectively remove nickel ions from wastewater. The modification process increases the surface area and porosity of the adsorbent, enhancing its adsorption capacity. The modified adsorbent (1.00 wt.% H2O2) showed a higher sorption capacity of 26.57 mg/g and efficiency of 85.22% compared to the non-modified adsorbent (10.55 mg/g) sorption capacity and 45.63% nickel removal efficiency, indicating the potential of hydrogen peroxide-modified adsorbents as an economical and ecologically sustainable solution for environmental applications, particularly for metal immobilization.