Due to their fast switching capabilities, silicon carbide (SiC) MOSFETs are increasingly used in high-voltage pulsed-power circuits where fast and flexible high-voltage pulses are required (e.g. for plasma-processing applications), such as in our solid-state Impedance-matched Marx generator. The turn-on time of SiC MOSFETs mainly depends on the gate-driving technique and its implementation. Therefore, many studies focus on SiC MOSFET gate-driving methods. In this article, a gate-boosting driving method that was previously proposed for IGBTs is optimized for SiC MOSFETs and applied to a very fast MOSFET to reduce turn-on time as much as possible. A prototype of the optimized gate-boosting driver was built and tested to assess its performance. The test results validate the effectiveness of the optimized gate-driving method and showed that a MOSFET turn-on time of below 2 ns is achievable at a high operating voltage and moderate current and below 3 ns for a wider range of load-current and operating-voltage conditions. Furthermore, current rise rates of 38.7 kA/μs at 356-A load current are possible. All these results are considerably faster than ever demonstrated before.
18 January 2023 in IEEE Transactions on Plasma Science
We developed a new pulsed power supply to study the influence of the high-voltage (HV) pulse shape on the generation of plasma-activated water (PAW). This article shows the design and implementation of the generator and evaluates its performance on resistive loads. The design is an improved version of the solid-state impedance-matched Marx generator (SS-IMG) concept as previously developed at Eindhoven University of Technology. The IMG concept allows for sub-nanosecond rise time pulses, to be able to create a nonthermal plasma very efficiently. A conventional SS-Marx generator (SS-Marx) circuit is taken as the starting point, and a careful implementation is made with most electrical connections analyzed as transmission lines (TLs). All these TLs are impedance-matched to each other and the load. The implemented generator is able to generate 25 ns to $\mu$ s duration pulses of 20 kV up to 10-kHz repetition rate in a 50- $\Omega$ load with about 8 ns rise time and arbitrary pulse shape. Future improvements are suggested which will increase the repetition rate and decrease the pulse rise time to the sub-nanosecond regime.
29 March 2023 in IEEE Transactions on Plasma Science
To measure the output voltage and current in our impedance-matched solid-state Marx generator we developed a voltage and current sensor integrated with the IMG structure. One of the advantages of our IMG structure is the coaxial inner transmission line (TL). The end of this TL is the output connection, which consists of a grounded ring and a smaller high-voltage (HV) inner conductor (coaxial). This structure is ideal for fitting D-dot and Rogowski-coil sensors, as these sensors can benefit from the strictly defined electric and magnetic fields in this waveguide. We developed D-dot and Rogowski-coil sensors on printed circuit boards (PCB) and show their usability in our application for measuring HV pulses. The sensors have a bandwidth of about 200 MHz, measure voltages up to 20 kV, and currents up to hundreds of amperes. Their simple PCB design makes them easily reproducible and cheap compared to commercial sensors. Although designed for our IMG, they can be fit on any coaxial line. Next, we made passive integrators to partly integrate the differentiated sensor signal, which improves the signal quality when measured with an oscilloscope. Finally, after software signal postprocessing, we achieve far better voltage measurements and similar current measurements compared to commercial probes.
18 March 2024 in Journal of Physics D: Applied Physics
To assess the species in plasma-treated water, two methods were compared: calibrated absorption spectroscopy and a method using pH and conductivity to determine the amount of dominant reactive species in the water. A function fitting method was developed for the analysis of the absorption spectra based on solutions with known concentrations. The influence of plasma treatment time on demineralized water and the concentration was studied using the two methods; the results in both cases show an almost linear growth with time. The method, utilizing pH and conductivity, shows consistent results with those achieved using UV absorption spectroscopy in considerably less time and in a more cost-efficient manner.
4 February 2026 in IEEE Transactions on Plasma Science
In numerous pulsed power applications, such as flash X-ray radiography, the voltage pulse shape plays a critical role to guarantee reliable and correct system operation. In particular, for flat-top pulses, the quality of the voltage plateau can be crucial to ensure optimum operating conditions. It can only be obtained if, first, the generator itself delivers a well-shaped pulse and, second, the assembly formed by the transmission line and the load has a matched impedance. However, certain factors, such as high-power levels or high signal frequencies, may introduce variations in the impedance at the load, resulting in a global mismatch. This article puts forward a new approach to mitigate impedance variations that degrade the voltage plateau at the load level. An original solution based on a variable resistor, which is comprised of surface-mount device (SMD) resistors combined with power transistors that operate as on–off switches, is proposed. These enable the device’s impedance to be adjusted dynamically. This article elaborates on the conceptual framework and design decisions that led to the development of an experimental prototype. It also presents initial experimental results in which a deliberately degraded voltage plateau, characterized by a peak reaching 1 kV, is corrected. This correction allows the original plateau quality to be restored with an accuracy of approximately2%.
1 September 2026 in IEEE Transactions on Plasma Science