A high-performance ZnSnO (ZTO) thin-film transistor (TFT) was fabricated, with ZTO deposited by rf magnetron sputtering. XPS was used to analyze and study the effects of different annealing temperatures on the element composition and valence state of ZTO films. Then, the influence mechanism of annealing treatment on the electrical properties of ZTO thin films was analyzed. The results show that, with an increase in annealing temperature, the amount of metal bonding with oxygen increases first and then decreases, while the oxygen vacancy decreases first and then increases. Further analysis on the ratio of Sn2+ is presented. Electrical results show that the TFT annealed at 600 °C exhibits the best performance. It exhibits high saturation mobilities (μSAT) up to 12.64 cm2V−1s−1, a threshold voltage (VTH) of −6.61 V, a large on/off current ratio (Ion/Ioff) of 1.87 × 109, and an excellent subthreshold swing (SS) of 0.79 V/Decade.
The preparation of thin-film transistors (TFTs) with InGaZnO (IGZO) channels using sol–gel technology has the advantages of simplicity in terms of process and weak substrate selectivity. We prepared a series of TFT devices with a top contact and bottom gate structure, in which the top contact was divided into rectangular and circular structures of drain/source electrodes. The field-effect performance of TFT devices with circular pattern drain/source electrodes was better than that with a traditional rectangular structure on both substrates. The uniform distribution of the potential in the circular electrode structure was more conducive to the regulation of carriers under the same channel length at different applied voltages. In addition, with the development of transparent substrate devices, we also constructed a hafnium oxide (HfO2) insulation layer and an IGZO active layer on an indium tin oxide conductive substrate, and explored the effect of circular drain/source electrodes on field-effect properties of the semitransparent TFT device. The IGZO deposited on the HfO2 dielectric layer by spin-coating can effectively reduce the surface roughness of the HfO2 layer and optimize the scattering of carriers at the interface in TFT devices.
14 October 2022 in Journal of Materials Science: Materials in Electronics
The preparation of thin-film transistors (TFTs) using ink-jet printing technology can reduce the complexity and material wastage of traditional TFT fabrication technologies. We prepared channel inks suitable for printing with different molar ratios of their constituent elements. Through the spin-coated and etching method, two different types of TFTs designated as depletion and enhancement mode were obtained simply by controlling the molar ratios of the InGaZnO channel elements. To overcome the problem of patterned films being prone to fracture during high-temperature annealing, a stepped annealing method is proposed to remove organic molecules from the channel layer and to improve the properties of the patterned films. The different interfaces between the insulation layers, channel layers, and drain/source electrodes were processed by argon plasma. This was done to improve the printing accuracy of the patterned InGaZnO channel layers, drain, and source electrodes, as well as to optimize the printing thickness of channel layers, reduce the defect density, and, ultimately, enhance the electrical performance of printed TFT devices.
We prepared an indium-free metal oxide thin-film transistor (TFT) using a double-active-layers structure at room temperature. We changed the growth sequence of Al-doped zinc oxide (AZO) and zinc oxide (ZnO) double-active-layers on Si/SiO2 substrates by magnetron sputtering deposition to regulate the field-effect performance of TFTs. According to the analysis of field-effect properties before and after annealing in different atmospheres, the performance of TFT devices with ZnO/AZO/SiO2/Si double-active-layers was obviously better than that with single AZO or ZnO active layer and inverted AZO/ZnO/SiO2/Si double-active-layers in the device structure. The active layer with higher carrier concentration (AZO in this case) was closer to the dielectric layer, which was more favorable for carrier regulation in TFT devices. In addition, the annealed device had a lower on/off ratio (Ion/Ioff), easier-to-reach on-state, and higher mobility. Furthermore, the performance of the devices annealed under vacuum condition was obviously better than that annealed under air atmosphere. The Ion/Ioff could reach 6.8 × 105 and the threshold voltage was only 2.9 V.
The ZnO/Ni2S3 composite has been designed and in situ synthesized on Ni foam substrate by two steps of electrodeposition. ZnO was achieved on Ni foam by a traditional potentiostatic deposition, followed by cyclic voltammetric (CV) electrodeposition, to generate Ni2S3, where the introduction of ZnO provides abundant active sites for the subsequent Ni2S3 electrodeposition. The amount of deposit during CV electrodeposition can be adjusted by setting the number of sweep segment and scan rate, and the electrochemical characteristics of the products can be readily optimized. The synergistic effect between the ZnO as backbones and the deposited Ni2S3 as the shell enhances the electrochemical properties of the sample significantly, including a highly specific capacitance of 2.19 F cm−2 at 2 mA cm−2, good coulombic efficiency of 98%, and long-term cyclic stability at 82.35% (4000 cycles).