24 January 2023 in Optica
High sensitivity avalanche photodiodes (APDs) operating at eye-safe infrared wavelengths (1400–1650 nm) are essential components in many communications and sensing systems. We report the demonstration of a room temperature, ultrahigh gain ( , , , ) linear mode APD on an InP substrate using a separate absorption, charge, and multiplication (SACM) heterostructure. This represents gain improvement ( ) over commercial, state-of-the-art InGaAs/InP-based APDs ( ) operating at 1550 nm. The excess noise factor is extremely low ( ) at , which is even lower than Si APDs. This design gives a quantum efficiency of 5935.3% at maximum gain. This SACM APD also shows an extremely low temperature breakdown sensitivity ( ) of , which is lower than equivalent InGaAs/InP commercial APDs. These major improvements in APD performance are likely to lead to their wide adoption in many photon-starved applications.
22 April 2022 in Journal of Lightwave Technology
Digital alloy and random alloy Al 0.85 Ga 0.15 As 0.56 Sb 0.44 avalanche photodiodes (APDs) exhibit low excess noise, comparable to Si APDs. Consequently, this material is a promising multiplication layer candidate for separate absorption, charge, and multiplication structure APDs with high gain-bandwidth product. Characterization of the impact ionization coefficients of electrons ( α ) and holes ( β ) plays an important role in the simulation of avalanche photodiodes. The multiplication gain curves of eight p + -i-n + and n + -i-p + APDs covering a wide range of avalanche widths have been used to determine the electric field dependence of the impact ionization coefficients of Al 0.85 Ga 0.15 As 0.56 Sb 0.44 . A large impact ionization coefficient ratio between that of electrons to holes was seen across a wide electric field range. Simulations of the avalanche multiplication in these structures using a random path length (RPL) model gave good agreement with experimental results over almost three orders of magnitude, and a mixed injection method was employed to verify the extracted impact ionization coefficients. Interestingly, no difference in the impact ionization coefficients was seen between digital alloy and random alloy Al 0.85 Ga 0.15 As 0.56 Sb 0.44 . This knowledge of impact ionization coefficients is beneficial for the future utilization of the Al x Ga 1-x As y Sb 1-y material system.
19 September 2023 in Optics Express
AlxGa1-xAsySb1-y grown lattice-matched to InP has attracted significant research interest as a material for low noise, high sensitivity avalanche photodiodes (APDs) due to its very dissimilar electron and hole ionization coefficients, especially at low electric fields. All work reported to date has been on Al concentrations of x = 0.85 or higher. This work demonstrates that much lower excess noise (F = 2.4) at a very high multiplication of 90 can be obtained in thick Al0.75Ga0.25As0.56Sb0.44 grown on InP substrates. This is the lowest excess noise that has been reported in any III-V APD operating at room temperature. The impact ionization coefficients for both electrons and holes are determined over a wide electric field range (up to 650 kV/cm) from avalanche multiplication measurements undertaken on complementary p-i-n and n-i-p diode structures. While these ionization coefficients can fit the experimental multiplication over three orders of magnitude, the measured excess noise is significantly lower than that expected from the β/α ratio and the conventional local McIntyre noise theory. These results are of importance not just for the design of APDs but other high field devices, such as transistors using this material.
25 September 2023 in Applied Physics Letters
For short-wavelength infrared (SWIR) avalanche photodiodes, a separate absorption, charge, and multiplication design is widely used. AlInAsSb on an InP substrate is a potential multiplication layer with a lattice match to absorber candidates across the SWIR. Our new measurements demonstrate that AlInAsSb on InP is a promising multiplier candidate with a relatively low dark current density of 10−4 A/cm2 at a gain of 30; a high gain, measured up to 245 in this study; and a large differentiation of electron and hole ionization leading to a low excess noise, measured to be 2.5 at a gain of 30. These characteristics are all improvements over commercially available SWIR detectors incorporating InAlAs or InP as the multiplier. We measured and analyzed gain for multiple wavelengths to extract the ionization coefficients as a function of an electric field over the range 0.33–0.6 MV/cm.
6 December 2024 in Optica
Extended shortwave infrared (eSWIR) detectors capable of detecting wavelengths between 1.7 and 2.7 µm are useful for a wide range of applications, such as remote sensing and monitoring, but most of these detectors require cooling to reduce the dark currents. Identifying a suitable material that extends the wavelength range to well beyond 2 µm with minimal cooling is therefore important. The overall sensitivity of such a detector can be enhanced by using it in conjunction with a wide bandgap multiplication region which can increase the photocurrent via impact ionization. In this work, a systematic study of avalanche multiplication in seven Al0.9Ga0.1As0.08Sb0.92 diodes lattice matched to GaSb shows that the electron impact ionization coefficient (α) is larger than the hole impact ionization coefficient (β), especially at low electric fields. Using In0.22Ga0.78As0.19Sb0.89 (bandgap=0.45eV) as the absorber and Al0.9Ga0.1As0.08Sb0.92 (bandgap=1.6eV) as the multiplier in a separate absorption, charge, and multiplication region avalanche photodiode configuration enabled room temperature optical detection up to 2.75 µm with a peak external quantum efficiency (EQE) of >50% at the punch-through voltage (Vpt) ∼2µm wavelength. This device demonstrates a low excess noise of F=4.5 at a multiplication of M=20, giving rise to a noise equivalent power for an unoptimized device of 1.69×10−12W/Hz. A maximum multiplied EQE of >2000% at 2 µm is achieved before a low breakdown voltage of 18.9 V, obtained using a novel undepleted absorber design. This work shows the possibility of a high sensitivity eSWIR detector capable of operating at room temperature.
29 May 2023 in Applied Physics Letters
Low noise avalanche photodiodes (APDs) detecting 1550 nm wavelength play a crucial role in optical communication and LiDAR systems. These APDs utilize a separate absorption, charge, and multiplication (SACM) architecture with an absorber for 1400–1650 nm detection and a low noise, high gain multiplier that can be independently optimized for a high signal-to-noise ratio. Recently, GaAs0.5Sb0.5/Al0.85Ga0.15As0.56Sb0.44 SACM APDs have demonstrated ultra-high gain and extremely low noise, possibly improving sensitivity over Si and InGaAs/InP commercial APDs. This accomplishment was achieved using a GaAsSb absorber instead of a conventional InGaAs absorber, mitigating band discontinuities between the absorber and the multiplier. However, further optimization is required to reduce noise due to tunneling and impact ionization from the GaAsSb absorber, which occurs at a high electric field region. This paper focuses on the study of the high-field characteristics of GaAsSb photodiodes (PDs). The tunneling phenomenon is analyzed through current density-voltage measurements, and the impact ionization behavior is evaluated by measuring the multiplication of p-i-n GaAsSb PDs. The result suggests that when designing a SACM APD with a GaAsSb absorber, the electric field in the absorber can be increased to 175 kV/cm without the detrimental effects of ionization occurring in the absorber. The findings from this investigation will assist in optimizing GaAsSb-based SACM APDs and promoting further advancements in the 1550 nm APD technology.