Vishank Talesara

Vishank Talesara

Auto-generated profile, based on publicly available information

Vishank Talesara

Department of Electrical and Computer Engineering, The Ohio State University 1 , Columbus, Ohio 43210

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 March 2020 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
HXHao Xue
Hao Xue
KHKamal Hussain
Kamal Hussain
TRTowhidur Razzak
Towhidur Razzak
MGMikhail Gaevski
Mikhail Gaevski
SSShahadat Hasan Sohel
Shahadat Hasan Sohel
WLWu Lu
Wu Lu
We report on the demonstration of high current density in Al 0.65 Ga 0.35 N/Al 0.4 Ga 0.6 N heterojunction field effect transistors with micro-channels enabled by enhanced contact injection. Devices with a gate length of 100 nm exhibited a maximum current density of 910 mA/mm and a maximum transconductance of 140 mS/mm. A current gain cut off frequency of 20 GHz and maximum oscillation frequency of 36 GHz were obtained. Large-signal load-pull characterization of the transistors showed output power density of 2.7 W/mm at 10 GHz. The current density and output power density represent the state-of-art performance for high Al-composition AlGaN channel transistors.

20 March 2023 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
VTVishank Talesara
Vishank Talesara
YZYuxuan Zhang
Yuxuan Zhang
VVVijay Gopal Thirupakuzi Vangipuram
Vijay Gopal Thirupakuzi Vangipuram
Hongping ZhaoHongping Zhao
Hongping Zhao
WLWu Lu
Wu Lu
High power vertical GaN devices are in great demand recently due to their potential on extremely high-power conversion efficiency. Here, we show vertical GaN p–n power diodes fabricated on bulk GaN substrates with an optimized guard ring structure for electrical field management and high breakdown voltage. By using a low doped (∼1015 cm−3) 28 μm thick drift layer in combination with optimized ohmic contacts, a breakdown voltage (VB) of 4.9 kV and a low specific on-resistance (RON) of 0.9 mΩ cm2 were achieved. In combination with the high breakdown voltage and low specific on-resistance, the device demonstrated a Baliga figure of merit (V2B/RON) of 27 GW/cm2.

7 February 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
VTVishank Talesara
Vishank Talesara
DXDiang Xing
Diang Xing
XFXiangxiang Fang
Xiangxiang Fang
LFLixing Fu
Lixing Fu
YSYe Shao
Ye Shao
WLWu Lu
Wu Lu
Compared to Silicon counterparts, SiC power MOSFETs have lower on-state resistance and faster switching speed, which in-turn makes them better candidates for high-voltage power switching applications. This creates a growing need to develop device models for such SiC Power devices. In this study we show a sub-circuit model based on the analytical study using non-linear curve fitting method for modeling of dynamic switching behavior. Using a 1.2 KV, 17 A MOSFET as a testbed, this sub-circuit model is validated by implementing the model into Synopsys Saber in comparison with the measured DC characteristics, the Saber MOSFET tool model, and the manufacturer's model. The switching behavior of the device at 800 V/17 A and 800 V/5.5 A based on the sub-circuit model were also compared and validated with experimental measurements, the Saber MOSFET model, and manufacturer's model. Excellent agreements were achieved on both DC characteristics and switching behaviors. On the LTspice platform, the computation time of the analytical sub-circuit model is 4.5 times faster than the manufacturer's model. This sub-circuit model is adoptable and suitable for real time hardware in loop simulations and power converter designs.

25 April 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
VTVishank Talesara
Vishank Talesara
PGPaul. D. Garman
Paul. D. Garman
JLJames L. Lee
James L. Lee
WLWu Lu
Wu Lu
Graphene is a promising material for thermal management. Heating in power electronics is a severe issue since heat generation can lead to rise in device temperature which can cause performance degradation and device failure. However, current approaches are not so efficient because of the extremely small thermal mass of monolayer or few layers graphene. Here we show a new type of chemical vapor deposition (CVD)-grown thick graphene network with in-plane thermal conductivity of 1100 W/mK on ceramic substrates for thermal management of power switching devices. The demonstration of graphene network's thermal management capabilities was carried out on a 10-Ω resistor module and a 1.2-kV SiC mosfet package module. The results show that the thermal management performance using graphene coated on a low cost Al 2 O 3 direct-bonded copper (DBC) is significantly superior to the industry standard, costlier AlN DBC substrates. Specifically, the temperature of hot spots is lower by at least 25 °C when using CVD-grown graphene networks for thermal management. Numerical simulations suggest that the high in-plane thermal conductivity of thick graphene networks helps in quick transfer of heat away from the device. These demonstrations represent a transformative change on thermal management of WBG high-power switching devices.

2 October 2023 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
YXYibo Xu
Yibo Xu
VVVijay Gopal Thirupakuzi Vangipuram
Vijay Gopal Thirupakuzi Vangipuram
VTVishank Talesara
Vishank Talesara
JCJunao Cheng
Junao Cheng
YZYuxuan Zhang
Yuxuan Zhang
WLWu Lu
Wu Lu
Devices based on gallium nitride (GaN) have great potential for high power switching applications due to the high breakdown field and high electron mobility. In this work, we present a vertical GaN-on-GaN PN power diode using high dielectric constant material, BaTiO3, for electrical field management and high breakdown voltages, in together with an optimized guard-ring and field plate design. Numerical simulation shows that with high-k dielectrics implemented, the peak electrical field at the PN interface is mitigated from 3.5 to 3.1 MV/cm under a reverse bias of −9.05 kV. The device design with BaTiO3 shows a breakdown voltage of 9.65 kV or about 600 V improvement. The fabricated diodes with a 57 μm thick drift layer demonstrate a breakdown voltage of 7.86 kV on a bulk GaN substrate. The device has an on-resistance of 2.8 mΩ cm2 and a Baliga figure of merit of 22 GW/cm2.

2 November 2026 in Journal of Applied Physics
Verified
Journal Article
Closed access
VVVijay Gopal Thirupakuzi Vangipuram
Vijay Gopal Thirupakuzi Vangipuram
YXYibo Xu
Yibo Xu
YZYuxuan Zhang
Yuxuan Zhang
MDMatthias A. Daeumer
Matthias A. Daeumer
VTVishank Talesara
Vishank Talesara
Hongping ZhaoHongping Zhao
Hongping Zhao
Vertical GaN p-i-n diode electrical performance metrics are examined and correlated with sub-bandgap micro-photoluminescence (μ-PL) mapping. Two hundred device locations were measured via μ-PL after the metalorganic chemical vapor deposition of the device structure on a near-equilibrium ammonothermal GaN substrate. Post-microfabrication of full PIN diodes, electrical measurements were correlated with the acquired μ-PL data. Turn-on voltage and breakdown voltage are examined and correlated with μ-PL maps of each device area. It was found that the overall threading-dislocation (TD) density did not correlate significantly with the breakdown voltage. However, the areal sizing of the TD features when clustered together can significantly impact and correlate with the expected breakdown voltage. It was found that the higher the number of counts of μ-PL features with areas greater than 5 μm2 in each device area, the lower the resultant breakdown voltage is for the device. The results obtained here can provide a basis for a high-throughput, non-destructive, in-line metrology method that can be used for predicting vertical GaN device performance prior microfabrication and testing in a mass-manufacturing environment immediately after epitaxial device growth.