2 October 2023 in Applied Physics Letters
VVVijay Gopal Thirupakuzi Vangipuram
Vijay Gopal Thirupakuzi Vangipuram
+4
Devices based on gallium nitride (GaN) have great potential for high power switching applications due to the high breakdown field and high electron mobility. In this work, we present a vertical GaN-on-GaN PN power diode using high dielectric constant material, BaTiO3, for electrical field management and high breakdown voltages, in together with an optimized guard-ring and field plate design. Numerical simulation shows that with high-k dielectrics implemented, the peak electrical field at the PN interface is mitigated from 3.5 to 3.1 MV/cm under a reverse bias of −9.05 kV. The device design with BaTiO3 shows a breakdown voltage of 9.65 kV or about 600 V improvement. The fabricated diodes with a 57 μm thick drift layer demonstrate a breakdown voltage of 7.86 kV on a bulk GaN substrate. The device has an on-resistance of 2.8 mΩ cm2 and a Baliga figure of merit of 22 GW/cm2.
1 March 2025 in APL Electronic Devices
Ultrawide bandgap (UWBG) semiconductor β-phase Ga2O3 has attracted significant interest for potential power electronics applications. This, however, is hindered by the lack of effective p-type dopants in β-Ga2O3. A p–n heterojunction utilizing the recently discovered UWBG p-type LiGa5O8 in conjunction with n-type (010) β-Ga2O3 is demonstrated in this work. Ohmic contacts to the UWBG p-type material, LiGa5O8, were achieved via a combinational Pt/Ni/Au metal stack. Obvious improvement in contact resistance was observed with annealing of the contact metal at 375 °C for 1 min in N2 ambient. Rectifying characteristics with a turn-on voltage of 5.46 V and an ideality factor of 2.78 were extracted from the p-LiGa5O8/n-Ga2O3 heterojunction. Current density change of more than 7 orders of magnitude was obtained between the off-state and on-state of the diodes measured. This work provides a potential pathway to fully utilize the high breakdown field associated with β-Ga2O3 for high power device applications with a p-type material that has an even wider bandgap (and therefore a potentially higher breakdown field) than β-Ga2O3.
13 April 2026 in APL Electronic Devices
GaN-based power devices have great potential for medium-to-high voltage applications. In this work, we present the device design of a vertical GaN-on-GaN PN power diode using a double field plate structure and guard-rings for electrical field management to achieve a 10 kV breakdown voltage. Simulations show that this device design with a 75 μm thick drift layer and a doping density of 1 × 1015 cm−3 has a breakdown voltage of 10.5 kV and ∼90.5% electrical field management efficiency. Experimentally, the fabricated diode with a ∼74 μm thick drift layer and Nd–Na concentration of 1 × 1015 cm−3 demonstrates a breakdown voltage of 10.3 kV on a bulk GaN substrate. The device has an on-resistance of 8 mΩ cm2 and a Baliga figure of merit of 13.3 GW/cm2. Compared to the theoretical breakdown voltage of this device design, the fabricated device has an overall breakdown efficiency of 89%.
2 November 2026 in Journal of Applied Physics
Vertical GaN p-i-n diode electrical performance metrics are examined and correlated with sub-bandgap micro-photoluminescence (μ-PL) mapping. Two hundred device locations were measured via μ-PL after the metalorganic chemical vapor deposition of the device structure on a near-equilibrium ammonothermal GaN substrate. Post-microfabrication of full PIN diodes, electrical measurements were correlated with the acquired μ-PL data. Turn-on voltage and breakdown voltage are examined and correlated with μ-PL maps of each device area. It was found that the overall threading-dislocation (TD) density did not correlate significantly with the breakdown voltage. However, the areal sizing of the TD features when clustered together can significantly impact and correlate with the expected breakdown voltage. It was found that the higher the number of counts of μ-PL features with areas greater than 5 μm2 in each device area, the lower the resultant breakdown voltage is for the device. The results obtained here can provide a basis for a high-throughput, non-destructive, in-line metrology method that can be used for predicting vertical GaN device performance prior microfabrication and testing in a mass-manufacturing environment immediately after epitaxial device growth.