28 April 2014 in The Journal of Physical Chemistry C
3 April 2018 in Journal of Applied Physics
We present in this paper the use of Gas Source Molecular Beam Epitaxy for the large-scale growth of transition metal dichalcogenides. Fiber-textured MoS2 co-deposited thin films (down to 1 MLs) are grown on commercially 200 mm wafer size templates where MX2 crystalline layers are achieved at temperatures ranging from RT to 550 °C. Raman Spectroscopy and photoluminescence measurements along with X-Ray Photoelectron Spectroscopy show that a low growth rate is essential for complete Mo sulfurization during MoS2 co-deposition. Finally, cross-section Transmission Electron Microscopy investigations are discussed to highlight the influence of SiO2 and Al2O3 used surfaces on MoS2 deposition.
22 October 2013 in Journal of Materials Chemistry C
Block copolymers (BCPs) are seen as a possible cost effective complementary technique to traditional lithography currently used in the semiconductor industry. This unconventional approach has received increased attention in recent years as a process capable of facilitating the ever decreasing device size demanded. Control over microdomain orientation and enhancing long range order are key aspects for the utility of BCPs for future lithographic purposes. This paper provides an efficient route for the fabrication of highly ordered nanostructures suitable for such application. We investigate the significant effect of surface treatment regarding the self-assembly process of polystyrene-block-poly(4-vinylpyridine) (PS-b-P4VP) by employing an ethylene glycol layer, producing well defined perpendicular P4VP cylinders with long range order over large surface areas. Nanopores are generated through surface reconstruction using a preferential solvent, which allows for the incorporation of an inorganic moiety. Treatment of this pattern with UV/Ozone leads to formation of well-ordered iron oxide nanodots with a pitch of ∼26 nm. Furthermore, high aspect ratio silicon nanopillars result following pattern transfer (using Ar/O2).
27 September 2013 in Scientific Reports
RSRamsankar Senthamaraikannan
Ramsankar Senthamaraikannan
+2
Highly dense hexagonally arranged iron oxide nanodots array were fabricated using PS-b-PEO self-assembled patterns. The copolymer molecular weight, composition and choice of annealing solvent/s allows dimensional and structural control of the nanopatterns at large scale. A mechanism is proposed to create scaffolds through degradation and/or modification of cylindrical domains. A methodology based on selective metal ion inclusion and subsequent processing was used to create iron oxide nanodots array. The nanodots have uniform size and shape and their placement mimics the original self-assembled nanopatterns. For the first time these precisely defined and size selective systems of ordered nanodots allow careful investigation of magnetic properties in dimensions from 50 nm to 10 nm, which delineate the nanodots are superparamagnetic, well-isolated and size monodispersed. This diameter/spacing controlled iron oxide nanodots systems were demonstrated as a resistant mask over silicon to fabricate densely packed, identical ordered, high aspect ratio silicon nanopillars and nanowire features.
25 March 2014 in Journal of Vacuum Science & Technology A
A design of experiments methodology was used to optimize the sheet resistance of titanium nitride (TiN) films produced by plasma-enhanced atomic layer deposition (PE-ALD) using a tetrakis(dimethylamino)titanium precursor in a N2/H2 plasma at low temperature (250 °C). At fixed chamber pressure (300 mTorr) and plasma power (300 W), the plasma duration and N2 flow rate were the most significant factors. The lowest sheet resistance values (163 Ω/sq. for a 20 nm TiN film) were obtained using plasma durations ∼40 s, N2 flow rates >60 standard cubic centimeters per minute, and purge times ∼60 s. Time of flight secondary ion mass spectroscopy data revealed reduced levels of carbon contaminants in the TiN films with lowest sheet resistance (163 Ω/sq.), compared to films with higher sheet resistance (400–600 Ω/sq.) while transmission electron microscopy data showed a higher density of nanocrystallites in the low-resistance films. Further significant reductions in sheet resistance, from 163 Ω/sq. to 70 Ω/sq. for a 20 nm TiN film (corresponding resistivity ∼145 μΩ·cm), were achieved by addition of a postcycle Ar/N2 plasma step in the PE-ALD process.
23 September 2015 in Chemistry of Materials
Bismuth ferrite (BiFeO3) is a widely studied material, because of its interesting multiferroic properties. Bismuth self-limiting growth of single-phase BiFeO3 (BFO) has previously been achieved using molecular beam epitaxy (MBE), but the growth of BFO by chemical vapor deposition (CVD) has proved to be very challenging, because of the volatile nature of bismuth. The growth window regarding temperature, pressure, and precursor flow rates that will give a pure perovskite BFO phase is normally very small. In this work, we have studied the metal–organic CVD (MOCVD) growth of epitaxial BFO thin films on SrTiO3 substrates and found that by carefully controlling the amount of the iron precursor, Fe(thd)3 (where thd = 2,2,6,6 tetra-methyl-3,5-heptanedionate), we were able to achieve bismuth self-liming growth, for the first time. The effect of the volume of the bismuth and iron precursors injected on the growth of BFO thin films is reported, and it has been found that the phase-pure films can be prepared when the Bi/Fe ratios are between 1.33 and 1.81 under temperature and pressure conditions of 650 °C and 10 mbar, respectively, and where the O2 gas flow was kept constant to 1000 sccm out of a total gas flow of 3000 sccm. Piezoresponse force microscopy (PFM) studies demonstrate the presence of bipolar switching in ultrathin BFO films.