1 October 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In this work, third-quadrant I-V characterization and surge current tests are carried out on SiC asymmetric trench MOSFET (DUT A) and SiC double-trench MOSFET (DUT B) under various gate-source biases (VGS). The surge capability is found to be uninfluenced by VGS for DUT A. However, it has a 71.4% increase when VGS changes from 0V to -5V for DUT B. The I-V characteristics in third quadrant are measured under various VGS. It is found that the channel is open when the source-drain voltage is >2.5V for DUT A and >1.5V for DUT B at VGS=0V. High temperature measurements are also conducted from 298K to 448K. When VGS=0V, the channel current takes up to 50% at 10A source-to-drain current for DUT B, whereas only 10% for DUT A. This could lead to high current/heat density in the channel of DUT B. The transient resistance is also extracted from the surge I-V trajectories and it is higher for DUT B tested under VGS=0V, which will increase the dissipated surge energy. Finally, failure mechanism is analyzed. For DUT A, aluminum melting contributes to the failure at VGS=-5V and VGS=0V. For DUT B tested at VGS=0V, earlier breakdown happens due to gate oxide failure.
3 August 2020 in IEEE Transactions on Electron Devices
In this article, the avalanche capability of the 1.2-kV 4H-SiC junction barrier Schottky (JBS) and merged p-i-n Schottky (MPS) diodes is investigated through simulation and experiments. For MPS diodes, the width of the wide P+ region (W) is found to have great effects on the device avalanche capability. MPS diodes with varied W-values (3-20 μm) and JBS diode are designed and fabricated, and their avalanche energy/current capability is tested with unclamped inductive switching tests. The experimental results show that the MPS diode has an optimized avalanche capability at W = 8-μm design. Simulation study reveals that the avalanche current is mainly distributed at the edges of the P+ regions in the JBS/MPS diodes as a result of the curvature-effect-induced electric field crowding. The localized current crowding and unbalanced current distribution in the avalanche mode contribute to a reduced effective power dissipation area and a weaker avalanche capability. The current nonuniformity coefficient (k) is used to characterize the severity of the current unbalance, and it is found that k declines as W increases when W = 3-8 μm and then gets increased when W exceeds 8 μm. Both the experimental and simulation results indicate that the MPS diode is superior to the JBS diode in avalanche capability, and the width of the wide P+ region in the MPS diode has an optimal design (8 μm in this article) which corresponds to the alleviated current crowding issue and 9%-19% improvement of the avalanche capability.
8 October 2018 in IEEE Electron Device Letters
Trench termination with SiO2-encapsulated dielectric for 4H-SiC devices is proposed and experimentally demonstrated. The trench is mainly refilled with spin-on dielectric which is encapsulated with SiO2 to protect it from the high electric field in the trench. Such a trench termination is fabricated along with a high-voltage p-i-n diode. The fabricated device shows a repeatable breakdown voltage over 1750 V (96% of the ideal planar junction breakdown) with a termination length of 14 μm while the conventional trench termination has unrepeatable breakdown and requires over 30 μ m termination length. Also, this termination length is less than ~1/4 of the dimension of a field limiting rings (FLR) termination. Moreover, the fabrication process is robust with a large process window (Trench width ≥14 μm).
23 August 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In this work, the influences of P-well design and turn-off gate-to-source bias on the surge robustness of SiC MOSFET’s body diode are studied. Devices with high and low P-well doping concentration designs are stressed with surge current pulses when the gate-to-source is biased with 0 or −5 V. The gate-to-source bias is found to have effects on the surge capability of the low P-well doping-designed device. In the case of 0-V bias, the channel is prone to turning on and acquires a higher surge capability than the devices under the −5 V. On the other hand, the surge capability of high P-well doping-designed device is found less influenced by the gate-to-source bias. Furthermore, threshold voltage instability after repetitive surge pulses is also investigated. The device with low P-well doping shows better threshold stability due to its lower interface trap density. Based on the results above, a design methodology is proposed from the view of device mechanism and operation condition. Relatively low P-well doping design and negative gate bias are recommended for SiC MOSFET, as they can improve the single-pulse surge robustness of body diode and minimize the threshold voltage instability in repetitive surge pulse events.
7 August 2019 in IEEE Access
Flowmeters play a critical role in hydraulic systems. Following a review of positive displacement flowmeters, we hereby introduce a novel positive displacement flowmeter with parallel two-dimensional pistons as metering units. The working principle involves simultaneously utilizing both the rotational and reciprocation movements of a two-dimensional piston and paralleling two two-dimensional pistons to prevent flow rate fluctuations. Consequently, we established a mathematical model to describe the cam track curves and the displacement of the flowmeter. Meanwhile, the pressure loss is analyzed and the leakage flow rate is estimated to compensate the relative error. Finally, we designed and fabricated a prototype to measure the flow rate with ranges of 1 – 25 L/min. The experimental results show that the prototype has a reading uncertainty of less than 2%, a linearity of around ±3.8% and relative errors of less than ±2.9%. The pressure loss for the prototype increases linearly with the total flow rate and reaches 3 bar at 25 L/min. These characteristics are acceptable considering that this prototype is the first set of two-dimensional piston flowmeters. The shortcomings of this first-generation flowmeter are discussed in the conclusion part to provide guidance to enhance the performance of next-generation prototypes.
31 July 2023 in IEEE Transactions on Electron Devices
In this article, a structure design concept plasma spreading layer (PSL) has been introduced into planar silicon carbide (SiC) MOSFETs. Devices’ static characteristics, gate–drain capacitance ( $\textit{C}_{\text{gd}}\text{)}$ , and short-circuit (SC) robustness are studied with experiments. The PSL structure can increase the breakdown voltage (BV) and reduce $\textit{C}_{\text{gd}}$ of the devices. The MOSFETs with the PSL exhibit an 11.6% higher Baliga’s figure of merit (BFOM) and a 75% higher 1/high-frequency figures-of-merit (HF-FOM). Moreover, they have better SC robustness by 60%, 67%, and 33% under 400-, 600-, and 800-V dc bus voltage than that of the traditional one. Combined with the experimental data and the 3-D simulation results, the MOSFETs with the PSL have enhanced JFET effects, which reduces the electric potential, SC current density, and electric field in the JFET region during the SC process, so as to enhance the SC robustness. The SC failure mechanisms are studied with emission microscope (EMMI) analysis, focused ion beam (FIB) observation, and simulations.