30 March 2024 in Mining of Mineral Deposits
Purpose.The research purpose is to assess the stability of mine workings driven in a stratified rock mass by studying the influence of the stratified rock bedding angle on the rock mass stress-strain state (SSS). Methods. The research uses both experimental and numerical methods. Experimental studies are carried out using rock samples with different angles of rock layer occurrence, while numerical modeling is performed using the RS2 (Geotechnical Finite Element Analysis) software based on the generalized Hoek-Brown failure criterion. The studies are carried out on models covering the border area of the mine workings driven in the mass with the angles of rock occurrence from 0 to 75°. Findings. Experimental and numerical studies have shown that when the rock layer inclination angle changes, significant changes occur in the stress concentration zones around the mine workings. An increased rock layer inclination angle is accompanied by a change in stress distribution, which is important for assessing the stability of mine workings. A particularly strong influence is observed at the angles of rock occurrence 30° and above. Originality. The research novelty is in revealing the patterns in the stress distribution in the stratified rock masses depen-ding on the rock layer inclination angle. Research results provide new data on the rock interaction mechanisms in difficult geological conditions. Practical implications. The results obtained can be used in the planning and operation of mine workings in difficult geological conditions. By taking into account the changes in stress zones caused by the rock layer inclination angle, it is possible to improve the safety and efficiency of mining operations.
30 September 2022 in Mining of Mineral Deposits
Purpose. Studying the stress-strain state of the rock mass under the open pit, taking into account the change in the open-pit bottom width in order to reveal the geomechanical state and determine the safe parameters of the rock bridge. Methods. The peculiarities of the stress-strain state formation in the transition zone have been studied according to the methodology using numerical research methods and taking into account the geological strength index (GSI). Using this index, it is possible to take into account rock fracturing, water cut, lithology and other strength indicators, due to which there is a correct transition from the rock sample strength to the mass strength. Findings. Based on the numerical modeling results, it has been determined that an increase in the open-pit bottom width leads to a decrease in the zone of tensile stresses concentration in the arch pillar of the stope block. This, in turn, has a positive effect on the rock bridge stability, that is, the probability of the rock bridge collapse does not increase with an increase in the width of the open-pit bottom. Originality. For the first time, the dependence has been obtained of the horizontal stresses σ3 distribution at the stages of the open-pit bottom expansion at the Akzhal Zinc-Lead Mine. This makes it possible to realistically predict changes in the geomechanical state of the rock bridge depending on the width of the open-pit bottom. Practical implications. When predicting the change in the stress-strain state in the transition zone and determining the rock bridge safe parameters, it is possible to reduce the probability of their destruction and make timely management decisions on safe conditions for mining the reserves.
1 September 2025 in Civil Engineering Journal
This paper presents a methodology for assessing the stability of stoping chambers and inter-chamber pillars (ICPs) during underground mining of ore bodies with varying dip angles. The objective is to determine optimal parameters for excavation elements (chamber width and pillar spacing) that ensure the stability of the mining system under fractured rock mass conditions. The Zhezkazgan deposit’s geomechanical properties were used as the modeling case study. The methodology includes geotechnical core mapping (with RQD, Q-system, and GSI classifications), laboratory strength testing, field–laboratory correlation, and numerical modeling using the finite element method. Particular focus is placed on the sensitivity of stability to variations in GSI, depth, and excavation geometry. The results indicate that increasing the dip angle significantly reduces the stability of both chambers and pillars. The novelty of this study lies in the comprehensive assessment of structural factors and excavation geometry on mass stability under site-specific geological conditions.
6 November 2025 in Горный журнал Казахстана
В условиях истощения запасов полезных ископаемых возрастает актуальность разработки остаточных запасов в сложных геомеханических условиях. Существенным фактором, влияющим на устойчивость очистных выработок, является наличие ранее отработанных пространств, формирующих вторичное напряженно-деформированное состояние массива. В исследовании методом конечных элементов (RS2) проанализировано влияние межвыработочного расстояния на устойчивость выработок в зоне техногенных обнажений. Установлено, что при расстоянии менее 10 м происходит слияние зон пластических деформаций, что ведет к потере несущей способности целика и смещению кровли и почвы. Оптимальные условия достигаются при расстоянии 20–25 м, когда коэффициент запаса прочности возрастает, а зоны пластических деформаций остаются изолированными. Полученные результаты обосновывают рациональные параметры системы разработки и позволяют оптимизировать управление горным давлением Пайдалы қазбалар қорының сарқылу жағдайында күрделі геомеханикалық жағдайда қалған қорларды игеру өзекті бола түсуде. Тазарту қазбаларының тұрақтылығына әсер ететін маңызды факторлардың бірі – массивтің екінші реттік кернеулі-деформацияланған күйін қалыптастыратын бұрынғы қазылған кеңістіктердің болуы. Зерттеуде соңғы элементтер әдісі (RS2) арқылы техногендік ашылымдар аймағындағы қазбалардың тұрақтылығына аралық қашықтықтың ықпалы талданды. 10 м-ден аз қашықтықта пластикалық деформация аймақтарының қосылуы байқалып, бұл целиктің көтергіш қабілетін жоғалтуына және қазбалардың төбе мен табанының ығысуына әкелетіні анықталды. 20–25 м аралықта оңтайлы жағдай қалыптасады: беріктік қоры коэффициенті артып, пластикалық деформация аймақтары оқшауланған күйде қалады. Алынған нәтижелер жүйелі игеру параметрлерін ғылыми негіздеуге және тау-кен қысымын басқаруды оңтайландыруға мүмкіндік береді In the context of mineral resource depletion, the development of residual reserves under complex geomechanical conditions becomes increasingly relevant. A significant factor influencing the stability of stopes is the presence of previously mined-out areas, which form a secondary stress-strain state of the rock mass. In this study, the finite element method (RS2) was used to analyze the effect of inter-excavation distance on the stability of workings within the influence zone of man-made openings. It was found that at distances of less than 10 m, plastic deformation zones merge, leading to the loss of the pillar’s load-bearing capacity and displacements of the roof and floor. Optimal conditions are achieved at distances of 20–25 m, where the factor of safety increases and the plastic deformation zones remain isolated. The obtained results provide a scientific basis for rational design parameters of the mining system and allow optimization of ground pressure control.
13 October 2023 in Горный журнал Казахстана
Мақалада натурадағы зерттеу (сейсмикалық барлау) нәтижелерін БАБО әдістемесінің нәтижелерімен салыстыру нәтижелері келтірілген, кері есептеу әдісі бойынша Жаман-Айбат кен орны жағдайында таужыныстардың сырғу параметрлері анықталған. Жаман-Айбат кен орнының кендері мен жыныстарының механикалық қасиеттерін зерттеу нәтижелері бойынша кен орнындағы кендер серпімді, серпімді деформациялардың потенциалдық энергиясын жинақтауға қабілетті, сыну сипаты сынғыш болып табылады. Оның негізінде тау-кен тектоникалық соққысының (техногендік жер сілкінісі) пайда болуын болдырмау үшін іргелес жоғарғы қабаттың отыру жағдайын анықтайтын өлшем ұсынылды. Камералық-бағаналы қазу жүйесінің негізгі геомеханикалық параметрі ретінде кентіректерді қайта игеру тәртібін жобалау үшін қажетті жер бетін толық өндіру (шөгу) шарты (НН / 1,09) анықталды The article presents the results of comparing the results of field studies (seismic exploration) with the results of the BABO technique, the sliding parameters were determined by the method of reverse calculation in the conditions of the Zhaman-Aybat deposit. According to the results of studies of the mechanical properties of the ore and rocks of the Zhaman-Aybat deposit, the ore at the deposit is elastic, capable of accumulating the potential energy of elastic deformations, with a brittle nature of destruction. On the basis of which a criterion is recommended that determines the condition for planting an overlying stratum to prevent the occurrence of a mountaintectonic shock (man-made earthquake) when planting an overlying stratum on a large part-time area. The condition of complete working of the Earth’s surface (НН/1,09) is established, which is necessary for designing the order of re-working of the whole, as the main geomechanical parameter of the chamber-pillar development system В статье приведены результаты сопоставления результатов натурных исследований (сейсморазведки) с результатами методики БАБО, по методу обратного расчета были определены параметры скольжения в условиях месторождения Жаман-Айбат. По результатам исследований механических свойств руды и пород месторождения Жаман-Айбат, руда на месторождении является упругой, способной к накоплению потенциальной энергии упругих деформаций, с хрупким характером разрушения. Авторами статьи предложен критерий, определяющий условие просадки налегающей толщи для предотвращения возникновения горно-тектонического удара (техногенного землетрясения) на большой площади. Установлено условие полной подработки земной поверхности (НН/1,09), необходимое для проектирования порядка повторной отработки целиков, как основной геомеханический параметр камерно-столбовой системы разработки
1 September 2026 in Journal of Human, Earth, and Future
This study presents a geomechanical assessment of the stress-strain state of a rock mass near mined-out areas using numerical modeling. The aim of the research is to establish the patterns of stress redistribution and the development of inelastic deformation zones around a development working (excavation) depending on the relative distance to the stope L/B, where L is the distance to the stope and B is the excavation width. Numerical modeling was performed using the finite element method in the RS2 software package, applying the Hoek-Brown strength criterion. The parameters of the rock mass were determined based on the processing of initial laboratory characteristics using the RSData software. The stress concentration factor K and the development of inelastic deformation zones were considered as the main analysis indicators. It was established that the dependence of the stress concentration factor K and the parameters of inelastic deformation zones on the relative distance L/B exhibits a pronounced nonlinear character. At small distances (L/B < 5), intensive interaction between the stope and the development working is observed, accompanied by maximum values of the stress concentration factor (up to 1.85-1.87) and significant development of inelastic deformation zones due to the superposition of stress fields. With increasing distance between the workings, the intensity of their mutual influence gradually decreases, which is manifested in a reduction of the stress concentration factor and a decrease in the size of inelastic deformation zones. At L/B = 6-7, spatial separation of inelastic deformation zones begins, accompanied by a significant weakening of the mutual influence of the workings, which allows this range to be considered as a rational distance when designing their mutual arrangement. The minimum values of the stress concentration factor and the smallest sizes of inelastic deformation zones are achieved in the range of L/B = 12-14, which indicates stabilization of the stress-strain state of the rock mass. With a further increase in distance, the parameters practically do not change, and the mutual influence of the stope and the development working becomes insignificant. The obtained results make it possible to substantiate rational distances between development workings and stopes, ensuring increased rock mass stability and reduced geomechanical risks in underground mining.