14 November 2022 in IEEE Electron Device Letters
An active-passivation p-GaN gate HEMT (AP-HEMT), featuring an active p-GaN passivation layer extending into the drain-side access region, is demonstrated on a commercial E-mode p-GaN/AlGaN/GaN heterostructure wafer. The active passivation layer (APL) is electrically connected to the p-GaN gate, and thus can supply/release mobile holes through gate electrode. The mobile holes in the APL effectively shields the overlaying surface traps from depleting the underlying 2DEG channel, and thus results in a much improved dynamic R on . After a 10-ms 650-V V DS stress, the measured dynamic R on /static R on is 4.30 for Conv-HEMT, but only 1.39 for AP-HEMT. Specially designed HEMTs with a surface testing electrode (ST) in the access region are fabricated to verify the screening effect. A negative V ST mimics the virtual gate effect caused by negative surface charges, resulting in a reduced drain current in conventional HEMT (Conv-HEMT). In the AP-HEMT, a negative V ST is shown to induce no change in the drain current, indicating an effective screening of the trap states. On the other hand, under a positive V ST stress applied to a Conv-HEMT, electrons in the 2DEG channel are pulled over the AlGaN barrier and get trapped at the surface, resulting in a sharply decreased drain current after positive V ST is removed. For the AP-HEMT, the drain current remain unchanged after the positive V ST is removed. The actively passivated HEMT exhibits the highly desired suppression of surface trap induced dynamic R on degradation.
30 May 2022 in IEEE Transactions on Electron Devices
To assess GaN power transistors’ capability to maintain a decent E-mode operation, ${V}_{\text {th}}$ at high ${V}_{\text {DS}}$ is measured for Schottky-type p-GaN gate HEMT, and an excessive negative ${V}_{\text {th}}$ shift is observed. With ${V}_{\text {DS}} =1$ V, ${V}_{\text {th}}$ is around 1.3 V at ${I}_{\text {D}} =1$ mA, but ${V}_{\text {th}}$ drops by ~0.6 V when measured at a high ${V}_{\text {DS}}$ of 100 V. In comparison, ohmic-type p-GaN gate HEMT only shows a negligible ${V}_{\text {th}}$ shift up to ${V}_{\text {DS}} =100$ V. A gate/drain coupled barrier lowering (GDCBL) effect is proposed to explain the appreciable ${V}_{\text {th}}$ shift in Schottky-type p-GaN gate HEMT. Upon high ${V}_{\text {DS}}$ , the potential of the floating p-GaN layer is raised by the drain through the capacitive coupling between p-GaN and drain ( ${C}_{\text {DP}}$ ). The positive potential of the p-GaN layer then lowers the energy barrier along the gated channel, resulting in a reduced ${V}_{\text {th}}$ . This effect is confirmed by the dependence of measured negative ${V}_{\text {th}}$ shift upon the property of gate/p-GaN contact and also by the numerical simulations that reveal the change in band diagrams upon high ${V}_{\text {DS}}$ .
20 February 2024 in IEEE Transactions on Electron Devices
Developing E-mode p-channel field-effect transistors (p-FETs) on the standard p-GaN gate HEMT epi-wafer is highly motivated to facilitate the realization of gallium nitride (GaN) complementary logic (CL) circuits and power-integrated circuits (PICs). The gate etching process is commonly employed in the fabrication of E-mode GaN p-FETs. However, due to gate etching-induced damage, the performance of E-mode GaN p-FETs often fails to meet expectations. To address the above issue, a post-etch wet treatment technique was developed in this work to enhance the performance of E-mode GaN p-FETs. The fabricated GaN p-FET with $\textit{L}_{\text{G}}$ $=$ 2 $\mu$ m exhibits an E-mode operation with $\textit{V}_{\text{th}}$ $=$ $-$ 2.9 V. The p-FET with post-etch wet treatment exhibits a current density of 5.4 mA/mm. Compared to the p-FET without wet treatment (1.9 mA/mm), the current density has increased by more than double. Atomic force microscopy (AFM) was utilized to characterize the surface morphology and validate the effectiveness of post-etch wet treatment. To suppress the leakage current, multienergy fluorine ion implantation was implemented for planar isolation of GaN p-FETs, high $\textit{I}_{\text{ON}}$ / $\textit{I}_{\text{OFF}}$ with over 6 $\times$ 10 $^{\text{5}}$ was obtained.
7 February 2024 in IEEE Transactions on Electron Devices
An enhancement-mode (E-mode) p-type gallium nitride (p-GaN) gate high electron mobility transistor with a gate termination extension (GTE-HEMT) has been developed on a sapphire substrate, intended for power switching applications of kilovoltage (kV) level. The GTE-HEMT device exhibits a low ON-resistance ( R $_{\biosc{on}}$ ) of 19.3 $\Omega$ $\cdot$ mm, corresponding to a specific R $_{\biosc{on}}$ ( R $_{\biosc{on},\text{SP}}$ ) of 7.33 m $\Omega$ $\cdot$ cm $^{\text{2}}$ . Notably, the GTE-HEMT has achieved a breakthrough by increasing the breakdown voltage (BV) to 2573 V, surpassing the conventional p-GaN gate HEMT (Conv-HEMT) with its BV of 1679 V. The enhanced BV is ascribed to the gate termination extension (GTE) that reduces the gate-edge electric field peak, similar to a junction termination extension (JTE) in traditional Si power devices. In addition, the dynamic R $_{\biosc{on}}$ of the GTE-HEMT has been improved, with a normalized dynamic R $_{\biosc{on}}$ (dynamic R $_{\biosc{on}}$ /static R $_{\biosc{on}}$ ) of 1.4 and 2.6 for 650-and 1200-V OFF-state stress, respectively. The GTE-HEMT has been benchmarked to the state-of-the-art GaN power transistors, demonstrating its potential for high-voltage applications.
28 December 2022 in IEEE Electron Device Letters
A 600-V p-GaN gate HEMT with buried hole spreading channel (BHSC) is demonstrated to suppress the buffer trap related dynamic ${R}_{\text {ON}}$ degradation. The BHSC is located at the interface between u-GaN and buried AlGaN. In the on-state, the holes injected from the p-GaN gate can effectively spread along the BHSC and screen the negative buffer charges. The hole spreading effect is verified by a detection of hole current from the sidewall of BHSC. The screening effect is verified by a positive substrate stress test that intentionally induces severe buffer trapping, which is widely known to cause severe dynamic ${R}_{\text {ON}}$ degradation in traditional GaN HEMTs. However, the propose device exhibits an immunity against buffer trapping owing to the screening effect of the holes along BHSC. The dynamic performance with as short as $\sim 20~\mu \text{s}$ delay after a 400-V substrate stress is characterized. Nearly zero buffer trap related dynamic ${R}_{\text {ON}}$ degradation is achieved.
31 August 2023 in IEEE Electron Device Letters
A 650-V p-GaN gate HEMT with Schottky source extension is proposed towards enhanced short-circuit (SC) reliability. At higher drain bias, a pinch-off point is formed at the edge of the Schottky source extension, resulting in reduced saturation current. High-voltage pulse I-V characterization is conducted for the devices in the ON-state to evaluate their SC reliability. With the similar OFF-state breakdown voltages ( BV s), the proposed device survives a much higher SC pulse voltage compared to the conventional p-GaN gate HEMT. Then, multiple short-circuit (SC) stress/test cycles are applied to the devices. For each stress, the drain voltage is increased by 50 V. The progressive degradation of R ON and OFF-state leakage current are recorded after each SC stress. The degradation of the proposed device is much slower than the conventional device. These results indicate that the proposed device is a promising solution for short-circuit rugged GaN power transistors.