This paper presents the development of an on-board bidirectional battery charger for Electric Vehicles (EVs) targeting Grid-to-Vehicle (G2V), Vehicle-to-Grid (V2G), and Vehicle-to-Home (V2H) technologies. During the G2V operation mode the batteries are charged from the power grid with sinusoidal current and unitary power factor. During the V2G operation mode the energy stored in the batteries can be delivered back to the power grid contributing to the power system stability. In the V2H operation mode the energy stored in the batteries can be used to supply home loads during power outages, or to supply loads in places without connection to the power grid. Along the paper the hardware topology of the bidirectional battery charger is presented and the control algorithms are explained. Some considerations about the sizing of the AC side passive filter are taken into account in order to improve the performance in the three operation modes. The adopted topology and control algorithms are accessed through computer simulations and validated by experimental results achieved with a developed laboratory prototype operating in the different scenarios.
This paper presents experimental results of electric vehicle (EV) operation as an off-line uninterruptible power supply (UPS). Besides the traditional grid-to-vehicle and vehicle-to-grid modes, this paper presents an improved vehicle-to-home operation mode. This new operation mode consists of the detection of a power outage in the power grid and the change of the EV battery charger control to operate as an off-line UPS. When the power grid voltage is restored, the voltage produced by the on-board EV battery charger is slowly synchronized with the power grid voltage before a complete transition to the normal mode. This paper presents results of two algorithms to detect a power outage: the root mean square (rms) calculation method based on half-cycle of the power grid voltage, and the rms estimation based on a Kalman filter. The experimental results were obtained in steady and transient state considering two cases with the EV plugged in at home: when charging the batteries and without charging the batteries. This paper describes the EV battery charger, the power outage detection methods, and the voltage and current control strategies.
Batteries of Electric Vehicles (EVs) and Plug-in Hybrid Electric Vehicles (PHEVs) have a large potential not only to provide energy for the locomotion of these vehicles, but also to interact, in dynamic way, with the power grid. Thereby, through the energy stored in the batteries, these vehicles can be used to regulate the active and the reactive power, as local Energy Storage Systems. This way, EVs can contribute to help the power grid to regulate the active and reactive power flow in order to stabilize the production and consumption of energy. For this propose should be defined usage profiles, controlled by a collaborative broker, taking into account the requirements of the power grid and the conveniences of the vehicle user. Besides, the interface between the power grid and the EVs, instead of using typical power converters that only work on unidirectional mode, need to use bidirectional power converters to charge the batteries (G2V - Grid-to-Vehicle mode) and to deliver part of the stored energy in the batteries back to the power grid (V2G - Vehicle-to-Grid mode). With the bidirectional power converter topology presented in this paper, the consumed current is sinusoidal and it is possible to regulate the power factor to control the reactive power, aiming to contribute to mitigate power quality problems in the power grid. To assess the behavior of the presented bidirectional power converter under different scenarios, are presented some computer simulations and experimental results obtained with a prototype that was developed to be integrated in an Electric Vehicle.
This paper presents a comprehensive comparison of a current-source converter and a voltage-source converter for three-phase electric vehicle (EV) fast battery chargers. Taking into account that the current-source converter (CSC) is a natural buck-type converter, the output voltage can assume a wide range of values, which varies between zero and the maximum instantaneous value of the power grid phase-to-phase voltage. On the other hand, taking into account that the voltage-source converter (VSC) is a natural boost-type converter, the output voltage is always greater than the maximum instantaneous value of the power grid phase-to-phase voltage, and consequently, it is necessary to use a dc-dc buck-type converter for applications as EV fast battery chargers. Along the paper is described in detail the principle of operation of both the CSC and the VSC for EV fast chargers, as well as the main equations of the power theory and current control strategies. The comparison between both converters is mainly established in terms of the total harmonic distortion of the grid current and the estimated efficiency for a range of operation between 10 kW and 50 kW.
This study presents control algorithms for a new unified power quality conditioner (UPQC) without the series transformers that are frequently used to make the insertion of the series converter of the UPQC between the power supply and the load. The behaviour of the proposed UPQC is evaluated in presence of voltage imbalances, as well as under non‐sinusoidal voltage‐and current conditions. The presented algorithms derive from the concepts involving the active and non‐active currents, together with a phase‐locked‐loop circuit. Based on these real‐time algorithms, and considering the proposed hardware topology, the UPQC is able to compensate the harmonic components of the voltages and currents, correct the power factor, and keep the load voltages regulated, all of this in a dynamic way, responding instantaneously to changes in the loads or in the electrical power system. The control algorithms were distributed in a two‐DSP digital control architecture, without any communication between them. Consequently, can be increased the sampling frequency of the acquired voltages and currents and improve the UPQC performance. Furthermore, some constraints of the proposed UPQC are evidenced, particularly when the main voltages are imbalanced. Simulation and experimental results are presented to verify the UPQC performance under transient and steady state conditions.
This paper presents the comparison between two three-phase Shunt Active Power Filters (SAPFs), one with Current-Source Inverter (CSI) and the other with Voltage-Source Inverter (VSI), which are used to compensate current harmonics and to control reactive power. The control algorithm of both SAPFs is based on the Instantaneous Reactive Power Theory (p-q Theory). The comparison here presented focuses on the Total Harmonic Distortion (THD) and RMS values of the compensated currents, and in the Total Power Factor (TPF) of the installation.