24 May 2021 in IEEE Electron Device Letters
We demonstrate ferroelectric (FE) memory transistors on a crystalline silicon channel with endurance exceeding 10 10 cycles. The ferroelectric transistors (FeFETs) incorporate a high- $\kappa $ interfacial layer (IL) of thermally grown silicon nitride (SiN x ) and a thin 4.5 nm layer of Zr-doped FE-HfO 2 (HZO) on a ~30 nm silicon on insulator (SOI) channel. The device shows a ~1V memory window (MW) in a DC sweep of just ± 2.5V, and can be programmed and erased with voltage pulses of $\text {V}_{\text {G}}= \pm \,\,3\text{V}$ at a pulse width of 250 ns. The device also shows very good retention behavior. These results indicate that appropriate engineering of the IL layer could substantially improve FeFET device performance and reliability.
2 February 2016 in Advanced Materials
27 July 2021 in IEEE Transactions on Electron Devices
We present compact models that capture published cryogenic temperature effects on silicon carrier mobility and velocity saturation, as well as fully depleted silicon on insulator (FDSOI) and fin field effect transistor (FinFET) devices characteristics within the industry-standard Berkeley short-channel IGFET model (BSIM) framework for cryogenic IC applications such as quantum computing. For the core model charge density/surface potential calculation, we introduce an effective temperature formulation to capture the effects of the band tail states. We also present a compact model that corrects the low-temperature threshold voltage for the band-tail states, Fermi–Dirac statistics, and interface traps. New temperature-dependent mobility and velocity saturation models are accurate down to cryogenic temperature. In addition, we propose that experimentally observed ${I}_{D}$ dependence of subthreshold swing (SS) at cryogenic temperatures is a consequence of the expectedly higher rate of Coulomb scattering of free carriers.
18 April 2022 in IEEE Electron Device Letters
In this work, we propose using deep learning to improve the accuracy of the partially-physics-based conventional MOSFET current-voltage model. The benefits of having some physics-driven features in the model are discussed. Using a portion of the Berkeley Short-channel IGFET Common-Multi-Gate (BSIM-CMG), the industry-standard FinFET and GAAFET compact model, as the physics model and a 3-layer neural network with 6 neurons per layer, the resultant model can well predict IV, output conductance, and transconductance of a TCAD-simulated gate-all-around transistor (GAAFET) with outstanding 3-sigma errors of 1.3%, 4.1%, and 2.9%, respectively. Implications for circuit simulation are also discussed.
27 April 2020 in IEEE Transactions on Electron Devices
We investigate the GaAs0.51Sb0.49/In0.53Ga0.47As negative-capacitance vertical-tunnel FET (NCVT-FET) to maximize its vertical tunneling over the corner tunneling. Negative capacitance enhances vertical tunneling more significantly than corner tunneling due to the amplified vertical electric field. By TCAD optimization of the device, small Ioff (10 pA/μm) and large Ion (405 μA/μm) at VDD = 0.5 V with 14 mV/dec sub-Vt swing over 4 dec of current were obtained. Even at VDD =0.1 V, the optimized NCVT-FET has 10 pA/μm Ioff, 5.86 μA/μm Ion (144x higher than the nominal TFET), and Ion/Ioff ratio of 6 x 10⁵.
14 June 2022 in IEEE Transactions on Electron Devices
A new deep learning (DL)-based parameter extraction method is presented in this brief; 50k training cases are generated by Monte Carlo simulations of these preselected parameters in Berkeley short-channel IGFET model (BSIM)-common multigate (CMG). DL models are trained using backward propagation with ${C} _{\text {gg}} - {V} _{g}$ and ${I} _{d} - {V} _{g}$ as the input and selected BSIM-CMG parameters as the output. A TCAD simulated FinFET device, calibrated to Intel 10-nm node, is used to test the DL models. The DL-based parameters extraction results show an excellent fit to capacitance and drain current data, with 0.16% rms error in ${C} _{\text {gg}} - {V} _{g}$ and 6.1% rms error in ${I} _{d} - {V} _{g}$ (0.69% rms error in above-threshold-voltage ${I} _{d} - {V} _{g}$ ), respectively. In addition, devices with a 10% variation in gate length and oxide thickness are successfully modeled with the trained DL model. The results show tremendous promise in using the DL-based models for parameter extraction.