An image sensor based on wide band gap silicon carbide (SiC) has the merits of high temperature operation and ultraviolet (UV) detection. To realize a SiC-based image sensor the challenge of opto-electronic on-chip integration of SiC photodetectors and digital electronic circuits must be addressed. Here, we demonstrate a novel SiC image sensor based on our in-house bipolar technology. The sensing part has 256 (16×16) pixels. The digital circuit part for row and column selection contains two 4-to-16 decoders and one 8-bit counter. The digital circuits are designed in transistor-transistor logic (TTL). The entire circuit has 1959 transistors. It is the first demonstration of SiC opto-electronic on-chip integration. The function of the image sensor up to 400 C has been verified by taking photos of the spatial patterns masked from UV light. The image sensor would play a significant role in UV photography, which has important applications in astronomy, clinics, combustion detection and art.
This letter presents the design, fabrication, and characterization of a 4H-SiC n-p-n bipolar junction transistor as a switch controlling an on-chip integrated p-i-n photodiode. The transistor and photodiode share the same epitaxial layers and topside contacts for each terminal. By connecting the collector of the transistor and the anode of the photodiode, the photo current from the photodiode is switched off at low base voltage (cutoff region of the transistor) and switched on at high base voltage (saturation region of the transistor). The transfer voltage of the circuit decreases as the ambient temperature increases (2 mV/°C). Both the on-state and off-state current of the circuit have a positive temperature coefficient and the on/off ratio is >80 at temperature ranged from 25 °C to 400 °C. It is proposed that the on/off ratio can be increased by ~1000 times by adding a light blocking layer on the transistor to reduce light induced off-state current in the circuit.
2 February 2018 in IEEE Journal of the Electron Devices Society
A low temperature (T max = 350 °C) process for Germanium (Ge) on insulator (GOI) substrate fabrication with thicknesses of less than 25 nm is reported in this paper. The process is based on a single step epitaxial growth of a Ge/SiGe/Ge stack on Si, room temperature wafer bonding and an etch-back process using Si 0.5 Ge 0.5 as an etch-stop layer. GOI substrates with surface roughness below 0.5 nm, 0.15% tensile strain, thickness nonuniformity of less than 3 nm and residual p-type doping of less than 10 16 cm -3 were fabricated. Ge pFETs are fabricated (T max = 600 °C) on the GOI wafer with 70% yield. The devices exhibit a negative threshold voltage of -0.18 V and 60% higher mobility than the SOI pFET reference devices.
Field effect transistors (FETs) based on networks of randomly oriented Si nanowires (Si nanonets or Si NNs) were biomodified using Thrombin Binding Aptamer (TBA–15) probe with the final objective to sense thrombin by electrical detection. In this work, the impact of the biomodification on the electrical properties of the Si NN–FETs was studied. First, the results that were obtained for the optimization of the (3-Glycidyloxypropyl)trimethoxysilane (GOPS)-based biofunctionalization process by using UV radiation are reported. The biofunctionalized devices were analyzed by atomic force microscopy (AFM) and scanning transmission electron microscopy (STEM), proving that TBA–15 probes were properly grafted on the surface of the devices, and by means of epifluorescence microscopy it was possible to demonstrate that the UV-assisted GOPS-based functionalization notably improves the homogeneity of the surface DNA distribution. Later, the electrical characteristics of 80 devices were analyzed before and after the biofunctionalization process, indicating that the results are highly dependent on the experimental protocol. We found that the TBA–15 hybridization capacity with its complementary strand is time dependent and that the transfer characteristics of the Si NN–FETs obtained after the TBA–15 probe grafting are also time dependent. These results help to elucidate and define the experimental precautions that must be taken into account to fabricate reproducible devices.
In this work atomic layer deposited Tm2O3 has been investigated as a high-k dielectric for Ge-based gate stacks. It is shown that when Tm2O3 is deposited on high-quality Ge/GeO2 gates, the interface state density of the gate stack is degraded. A series of post-deposition anneals are studied in order to improve the interface state density of Ge/GeOx/Tm2O3 gates, and it is demonstrated that a rapid thermal anneal in O2 ambient can effectively reduce the interface state density to below 5·1011 cm-2eV-1 without increasing the equivalent oxide thickness. Fixed charge density in Ge/GeOx/Tm2O3 gates has also been investigated, and it is shown that while O2 post-deposition anneal improves the interface state density, the fixed charge density is degraded.
27 December 2017 in IEEE Journal of the Electron Devices Society
4H-SiC p-i-n photodiodes with various mesa areas (40 000 μm 2 , 2500 μm 2 , 1600 μm 2 , and 400 μm 2 ) have been fabricated. Both C-V and I-V characteristics of the photodiodes have been measured at room temperature, 200 °C, 400 °C, and 500 °C. The capacitance and photo current (at 365 nm) of the photodiodes are directly proportional to the area. However, the dark current density increases as the device is scaled down due to the perimeter surface recombination effect. The photo to dark current ratio at the full depletion voltage of the intrinsic layer (-2.7 V) of the photodiode at 500 °C decreases ~7 times as the size of the photodiode scales down 100 times. The static and dynamic behavior of the photodiodes are modeled with SPICE parameters at the four temperatures.