Zuzana Mičicová

Zuzana Mičicová

Auto-generated profile, based on publicly available information

Zuzana Mičicová

Department of Materials Technologies and Environment, Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 November 2023 in Polimery
Verified
Journal Article
Open access
PDF file
ZMZuzana Mičicová
Zuzana Mičicová
MPMariana Pajtasova
Mariana Pajtasova
DODarina Ondrušová
Darina Ondrušová
SBSlavomíra Božeková
Slavomíra Božeková
SĎSilvia Ďurišová
Silvia Ďurišová
Róbert JaníkRóbert Janík
Róbert Janík
The influence of low-temperature plasma modification of bentonite on the dynamic-mechanical properties and vulcanization of rubber mixtures was examined. EDX, FTIR and TGA analysis were used to evaluate the filler. IR spectra of modified bentonite indicate lower intensity of the bands associated with OH groups and water. TGA confirms a smaller weight loss of samples subjected to plasma treatment, which also proves a lower water content in the mineral, confirming the effectiveness of the plasma treatment used.

16 April 2024 in Polimery
Verified
Journal Article
Open access
PDF file
SĎSilvia Ďurišová
Silvia Ďurišová
MPMariana Pajtasova
Mariana Pajtasova
DODarina Ondrušová
Darina Ondrušová
Róbert JaníkRóbert Janík
Róbert Janík
ZMZuzana Mičicová
Zuzana Mičicová
TKTomasz Klepka
Tomasz Klepka
The changes of rubber blend surface induced by atmospheric plasma at several conditions were studied via FTIR, SEM, contact angle and adhesion measurement. After plasma, the presence of OH, COO- bands of higher intensity was observed, whilst methylene groups reduced. A several formations of weaker agglomeration and cleaning of the surface was recognized. Also an intense decline of contact angles was observed. The plasma induced significantly greater changes at the 0.5 mm position, whereas emission times of 10 s and 30 s did not significantly affect the modifications of the investigated surface.


27 November 2023 in Polimery
Verified
Journal Article
Open access
PDF file
SBSlavomíra Božeková
Slavomíra Božeková
DODarina Ondrušová
Darina Ondrušová
MPMariana Pajtasova
Mariana Pajtasova
SĎSilvia Ďurišová
Silvia Ďurišová
ZMZuzana Mičicová
Zuzana Mičicová
TKTomasz Klepka
Tomasz Klepka
Instead of conventional carbon black, an alternative carbon filler (ACB) obtained in the pyrolysis process from tire waste was used for rubber compounds. The fillers were characterized using FTIR and TGA methods. The mechanical properties of the obtained rubber compounds and the influence of the fillers used on the vulcanization process, as well as the Payne effect, were examined. The results confirm the possibility of replacing conventional carbon black with an alternative carbon filler in rubber compounds.

16 April 2024 in Polimery
Verified
Journal Article
Open access
PDF file
MPMariana Pajtasova
Mariana Pajtasova
BPBeáta Pecušová
Beáta Pecušová
DODarina Ondrušová
Darina Ondrušová
AFAndrea Feriancová
Andrea Feriancová
SĎSilvia Ďurišová
Silvia Ďurišová
Dorota Czarnecka-KomorowskaDorota Czarnecka-Komorowska
Dorota Czarnecka-Komorowska
Effect of kaolinite modified with Cu(II), Co(II) and Ni(II) salts as a partial replacement for carbon black (1 and 8 phr) on the properties of the model tread rubber blend was examined. The blends were prepared in a two-stage process in a Brabender mixer at temperatures of 120°C and 100°C, respectively, with a constant mixing speed of 50 rpm. FT-IR confirmed the formation of copper hydroxyacetate monohydrate complex, which may indicate chemical interactions between rubber components and modified kaolinite. The filler improved technological parameters, tensile properties and hardness. Resistance to thermal aging has also increased.

7 November 2025 in Polimery
Verified
Journal Article
Open access
PDF file
ILIvan Labaj
Ivan Labaj
JVJuliána Vršková
Juliána Vršková
PSPetra Skalková
Petra Skalková
IKIvan Kopal
Ivan Kopal
DODarina Ondrušová
Darina Ondrušová
ZMZuzana Mičicová
Zuzana Mičicová
Instead of conventional carbon black (N550), an alternative carbon-based filler (AFC) - ash from the incineration of industrial waste - was used to obtain rubber compounds. The effect of this type of filler on the mixing and vulcanization process of rubber compounds was investigated. The addition of AFC reduced the maximum torque and real temperature of the compound. Compounds with a high AFC content were characterized by greater stiffness in the uncured state and significantly longer scorch times, while maintaining optimal vulcanization times. The obtained results indicate that AFC can partially or completely replace N550 in rubber compounds for conveyor belts without negatively impacting key processing parameters.