12 December 2023 in IEEE Transactions on Applied Superconductivity
In the frame of the Next Generation Europe program, the EU program to boost after-COVID recovery, the Italian Minister of University and Research has funded a project called Innovative Research Infrastructure for applied Superconductivity (IRIS). New laboratories will be built or upgraded in six poles: Milan (hub of the infrastructure), Genoa, Frascati, Naples, Salerno, and Lecce, to carry out basic research on magnetism and superconducting materials, test of wires, tapes, and large current cables, superconducting magnets construction with advanced instrumentation, power tests of magnets, and a special facility for high current-high voltage superconducting lines. The program will be executed over three years and then will operate for at least 10 years. It includes two first demonstrators: one HTS magnet to be operated at 10–20 K and a superconducting line of 1 GW (40 kA–25 kV) about 140 m long. The demonstrators anticipate the main scope of the investment in the IRIS infrastructure: to support the use of superconductivity for improving sustainability by decreasing the energy consumption without compromising performance. This article describes the global IRIS project.
1 December 2023 in IEEE Transactions on Applied Superconductivity
The quest for advancing science and technology continues with the Future Circular Collider (FCC), which requires 16 T bending dipoles to be installed along its 100 km tunnel to achieve a center-of-mass energy of 100 TeV, in its hadron-hadron version. The promising Nb $_{3}$ Sn technology for superconducting magnets presents a potential solution for large-scale production. In line with this, the European strategy for particle physics has urged for increased efforts in High Field Magnet R&D, specifically in constructing demonstrators for Nb $_{3}$ Sn technology. To address this call, the Istituto Nazionale di Fisica Nucleare (INFN) and CERN entered into an agreement to build a 1.5 m long cos-theta dipole in Nb $_{3}$ Sn, called Falcon Dipole (The Future Accelerator post-LHC Cos-theta Optimized Nb $_{3}$ Sn Dipole). The project aims to consolidate the fabrication process for Nb $_{3}$ Sn superconducting dipoles in the 12–14 T range, engaging industry partners in the initial stages of the R&D phase. This article provides a recall of the magnet design features and highlights the progress made in the development activities. Critical processes like the reaction treatment and the impregnation are discussed, with an emphasis on the test outcomes and the challenges faced. By taking these into account, plans for the production of the coils for the final configuration can be effectively formulated.
7 August 2024 in Superconductor Science and Technology
In the framework of studies on high-field magnets for future accelerators, a specific project called ASTRACT focuses on the effect of transverse strain on the critical current of Nb3Sn wires. The first phase of the project addresses the effects of strain imposed on Nb3Sn wires before heat treatment and the development of a procedure to directly compare critical current measurements with values extracted from magnetization cycles. A Nb3Sn RRP-Ti wire was deformed to different values of transverse strain (10%, 15%, 20%, and 25%), and long samples were collected for transport measurements at 4.2 K, in a background field ranging from 10 to 14 T. Short samples were used for magnetization measurements (VSM technique). Additionally, SEM images of the cross-section were collected at different longitudinal positions along the wire for each strain value. This paper proposes a method based on SEM image analysis and magnetization measurements analysis to study the effect of bundle deformation on transport properties. The procedure requires morphological information provided by SEM images after appropriate numerical processing. Verification through statistical comparison between the Ic transport and VSM data is also conducted. Direct critical current measurements showed no degradation due to deformation up to 25%. The method introduced, independent of transport data, can reach the same conclusions by considering the real shape of the bundles.
12 December 2024 in IEEE Transactions on Applied Superconductivity
In the context of the High Field Magnet (HFM) R&D program at CERN, this paper introduces a design proposal for a four-layer cos-theta Nb$_{3}$Sn dipole. Collaboratively developed by the Italian Institute of Nuclear Physics (INFN) and CERN, the dipole aims to contribute to the advancement of high-field Nb$_{3}$Sn magnets for future particle colliders, particularly the post-Large Hadron Collider (LHC) era. The target bore field is 14 T, potentially reaching 16T with a reduced margin of operation. Featuring a single aperture, the design incorporates four layers of state-of-the-art Nb$_{3}$Sn Rutherford cable configured in cos-theta, using the grading technique to exploit the performance of the conductor in the low-field region. To mitigate challenges associated with Nb$_{3}$Sn cable strain sensitivity, the magnet incorporates the Bladder&Key technique during the pre-loading phase to minimize coil stress. This paper delves into the preliminary electromagnetic design of the dipole, emphasizing optimization for high field quality and performance required for High Energy Physics Particle Accelerator standards. Using 2D Finite Element Method (FEM) simulations, the coil layout is designed, the margins are computed, and a comparison between different designs is made. Furthermore, a 3D FEM analysis is employed to investigate the location of the peak field within the magnet, with a specific focus on the design of coil ends.
13 October 2025 in IEEE Transactions on Applied Superconductivity
The Falcon Dipole is a project led by the Italian Institute of Nuclear Physics (INFN), which aims tofabricate a 12 T short model of a Nb$_{3}$Sn cos-theta accelerator dipole as part of the High Field Magnet (HFM) R&D program at CERN [1]. The status of the project is at the fabrication step of the first dummy coil in the industry and, in this paper, the results of the first campaign of winding tests conducted in the industry are presented. The winding process for the Falcon Dipole is challenging because the size of the Rutherford Cable used for the coils is comparable to the bore radius. This results in high bending and torsion stresses, making the cable structure unstable. To address these challenges, the previous 3D model has been modified to improve the winding feasibility. The setup has been prepared to monitor technical parameters that will help in modeling the coil geometry and identifying sources of critical issues. In this paper, the outcomes of the winding campaign are reported and the proposed changes to the coil end design to address the issues that arose are discussed.
23 February 2026 in IEEE Transactions on Applied Superconductivity
Following the publication of [1], the authors identified an error in the author list. Diego Perini has therefore been removed from the author list with agreement of all authors.