12 June 2024 in Science Robotics
Repetitive overhead tasks during factory work can cause shoulder injuries resulting in impaired health and productivity loss. Soft wearable upper extremity robots have the potential to be effective injury prevention tools with minimal restrictions using soft materials and active controls. We present the design and evaluation of a portable inflatable shoulder wearable robot for assisting industrial workers during shoulder-elevated tasks. The robot is worn like a shirt with integrated textile pneumatic actuators, inertial measurement units, and a portable actuation unit. It can provide up to 6.6 newton-meters of torque to support the shoulder and cycle assistance on and off at six times per minute. From human participant evaluations during simulated industrial tasks, the robot reduced agonist muscle activities (anterior, middle, and posterior deltoids and biceps brachii) by up to 40% with slight changes in joint angles of less than 7% range of motion while not increasing antagonistic muscle activity (latissimus dorsi) in current sample size. Comparison of controller parameters further highlighted that higher assistance magnitude and earlier assistance timing resulted in statistically significant muscle activity reductions. During a task circuit with dynamic transitions among the tasks, the kinematics-based controller of the robot showed robustness to misinflations (96% true negative rate and 91% true positive rate), indicating minimal disturbances to the user when assistance was not required. A preliminary evaluation of a pressure modulation profile also highlighted a trade-off between user perception and hardware demands. Finally, five automotive factory workers used the robot in a pilot manufacturing area and provided feedback.
1 June 2025 in IEEE Journal of Biomedical and Health Informatics
The Fugl Meyer Assessment (FMA) is a widely-used assessment for tracking motor function recovery post-stroke. Due to the limited access to rehabilitation, there exists a need for remote and automated assessment solutions. Wearable sensors and data-driven methods have shown promise for enabling automatic upper extremity FMA (FMA-UE) estimation, but minimizing user input motion and aligning with current clinical activities will aid the adoption of sensor-based assessments. In this work, we present an FMA-UE estimator which can make score predictions for a key subset of the assessment (70% of all items) using data from inertial measurement units (IMUs) placed on the arms and the trunk from three volitional reaching motions representative of functional daily activities. We collected a dataset of eleven stroke participants performing a subset of FMA-UE, and three reaching motions. The FMA-UE of each participant was assessed by an occupational therapist providing the labeled score for the training data. The estimator was trained on windowed data during FMA-UE motions and was able to make score estimates from reaching motions. Through leave-one-subjectout cross validation, the estimator achieved a normalized RMSE of 7%, which is comparable to or below the established minimal clinically important difference and minimal detectable change of FMA-UE of post-stroke individuals. Comparison experiments of various model designs also revealed the importance of trunk-based features inspired by compensation strategies common post stroke and features extracted from the hand sensor. The proposed estimator has the potential to broaden the possibility of automatic assessment via wearable sensors.
26 October 2022 in IEEE Access
Upper-limb exosuits are light wearable devices suitable for applications such as rehabilitation or assistance in industrial environments. One of the main drawbacks of these systems is the amount of uncertainties intrinsic to the nature of the device. Moreover, the direct interaction between the exosuit and its user adds disturbances to the system. Therefore, a robust control architecture to these phenomena is required for its appropriate control. In this article, a robust motion (position and speed) control architecture based on a cascade proportional-integral (PI) and a sliding mode controller (SMC), and a nonlinear disturbance observer (NDO) for the upper-limb cable-driven rehabilitation exosuit LUXBIT is designed. We call the proposed controller by the acronym CPISDO. The SMC nature allows to compensate the matched disturbances and uncertainties, while the NDO counteracts the unmatched ones. The PI component helps in reducing tracking error. Dynamic modelling, system architecture and control design are addressed. The CPISDO controller has been implemented over the exosuit and several experiments have been performed over 10 healthy subjects to evaluate the controller’s tracking performance as well as the disturbance rejection. Supertwisting (a state-of-the-art SMC) and PI controllers have been implemented for CPISDO validation. Results are compared with other state-of-the-art solutions.