This article introduces a millimeter-wave (mm-wave) multi-band transmit (Tx) phased-array design supp- orting the fifth-generation (5G) new radio frequency range 2 (NR FR2) bands. An eight-element phased-array module is presented employing two wideband 16–52 GHz $4{\times }1$ Tx beamformer chips and tapered slot Vivaldi antenna array. The beamformer chips are designed in a SiGe BiCMOS process and flipped on a printed circuit board (PCB). The SiGe integrated circuit (IC) has four differential radio frequency (RF) beamforming channels each consisting of an active balun, analog adder-based phase shifter (PS), variable gain amplifier (VGA), and a two-stage class-AB power amplifier (PA). The RF input signal is distributed to the four channels using a compact Wilkinson network. The measured peak gain is 28.3 dB with 13.5–14.7 dBm output $P_{1{\mathrm {dB}}}$ and 14–15.4 dBm $P_{{\mathrm {sat}}}$ at 20–50 GHz. Each channel dissipates 250 mW from 2 V and 3-V supplies at $P_{1\,{\mathrm{ dB}}}$ . The beamformer chip is tested using 64-QAM waveforms and achieves a data rate of 2.4 Gb/s at 5.2% rms EVM and 9.6-dBm average power. The eight-element phased-array module shows a broadband performance with excellent patterns and ±60° scanning capability and with a peak effective isotropic radiated power (EIRP) of 32–34 dBm at 19.5–51 GHz. At an EIRP of 21–22 dBm, 400-MHz 256-QAM 5G-NR compliant waveforms are transmitted with < 2.98% EVM demonstrating 5G NR FR2 operation. To the author’s knowledge, this work achieves the highest bandwidth phased array with a peak EIRP of 34 dBm enabling the construction of multi-standard/multi-band 5G phased-array systems.
7 January 2022 in IEEE Transactions on Microwave Theory and Techniques
This work presents a 15–57 GHz multiband/ multistandard phased-array architecture for the fifth-generation (5G) new radio (NR) frequency range 2 (FR2) bands. An eight-element phased-array receive module is demonstrated based on two four-channel wideband beamformer chips designed in the SiGe BiCMOS process and flipped on a low-cost printed circuit board. The SiGe Rx chip employs RF beamforming and is designed to interface to a wideband differential Vivaldi antenna array. Each channel consists of a low-noise amplifier (LNA), active phase shifter with 5-bit resolution, variable gain amplifier (VGA), and differential-to-single-ended stage. The four channels are combined using a wideband two-stage on-chip Wilkinson network. The beamformer has a peak electronic gain of 24–25 dB and a 4.7–6.2 dB noise figure (NF) with a −29 to −24 dBm input $P_{\boldsymbol {1\,dB}}$ at 20–40 GHz. The eight-element phased-array module also achieved ultra-wideband frequency response with flat gain and low-system NF. The phased array scans ±55° with $ < -12$ -dB sidelobes demonstrating multiband operation. A 1.2-m over-the-air (OTA) link measurement using the eight-element Rx module supports 400-MHz 256-QAM OFDMA modulation with < 2.76% error vector magnitude (EVM) at multiple 5G NR FR2 bands. To the author’s knowledge, this work achieves the widest bandwidth phased array enabling the construction of multistandard systems.
21 December 2022 in IEEE Transactions on Microwave Theory and Techniques
This article presents an eight-channel 5–33-GHz transmit phased-array radio frequency integrated circuit (RFIC) for $C$ -, $X$ -, $Ku$ -, and $Ka$ -band SATCOM applications. The $4\ttimes2$ beamformer is implemented in a 90-nm SiGe HBT process. Each channel has a wideband two-stage power amplifier (PA), a phase shifter (PS), a variable gain amplifier (VGA), and a single-ended to differential (S2D) converter. The input radio frequency (RF) power is distributed to the eight channels using a two-stage lumped-element Wilkinson network and active dividers. The measured electronic gain is 24–27 dB at 5–33 GHz with 5-bit PS operation and $>$ 20 dB gain control. A peak OP1dB and OPsat of 10.8–14 dBm is achieved over the entire frequency range. The chip is then implemented in a wideband phased array using tapered-slot (Vivaldi) antennas. The 16-element phased array achieves $\pm$$60^{\circ}$ scanning at $C$ -, $X$ -, and $Ku$ -bands and $\pm$$30^{\circ}$ scanning at $Ka$ -band with a broadside effective isotropic radiated power (EIRP) of 16–38.5 dBm at 8–32 GHz. Quadrature phase shift keying (QPSK), 8-phase shift keying (PSK), and 16-quadrature amplitude modulation (QAM) waveform are delivered to the phased array for performance evaluation, and ${<}$ 4%–4.8% error vector magnitude (EVM) is achieved in $C$ – $Ka$ -bands at P1dB (EIRP) operation. Application areas are $C$ -/ $X$ -/ $Ku$ -/ $Ka$ -band ground terminals for satellite communications (SATCOMs).
2 September 2022 in IEEE Transactions on Microwave Theory and Techniques
This article presents 16–52-GHz multiband transmit and receive phased arrays designed to support multistandard 5G communications. The 64-element arrays are built using $16\,\times\, 1$ linear arrays, and each has four $4\,\times\, 1$ beamformer chips on a six-layer printed circuit board (PCB) with a Wilkinson combiner/divider network and tapered slot antennas. The wideband beamformer chips are designed in a SiGe BiCMOS process and use the RF beamforming architecture. The arrays have $\pm$$60^{\circ}$ scanning capability in the azimuth plane and $\pm$$30^{\circ}$ in the elevation plane with low sidelobes. The 64-element Tx array achieves an effective isotropic radiated power (EIRP) of 50–51.7 and 47.6–49 dBm at $P_{\rm sat}$ and $P_{1\,{\rm dB}}$ , respectively, at 24.5–48 GHz. The 5G-NR-compliant waveforms with 400 MHz and up to 256-quadrature amplitude modulation (QAM) are transmitted with <2.98% EVM $_{\rm rms}$ and 34–36 dBm average EIRP Single-carrier (SC) 400-MHz 64-QAM waveforms are also transmitted achieving <3% EVM $_{\rm rms}$ with 39–40.3 dBm average EIRP and 2.4 Gb/s data rate. The 64-element Rx array achieves a system NF of 5.3–6.9 dB and a measured $G$ / $T$ of $-$ 19.3 to $-$ 14.4 dB (with T $_{\rm ant} = 295$ K) at 20–50 GHz, and $<$ 2.6% error vector magnitude (EVM) performance when tested with 400-MHz 256-QAM 5G-NR-complaint packets. To the author’s knowledge, this work achieves the highest bandwidth Tx and Rx phased array systems suitable for multiband 5G operation.
16 March 2023 in IEEE Transactions on Microwave Theory and Techniques
This article presents an eight-element, 28-/39-GHz dual-band, dual-polarized phased array for user equipment, such as computers, cell phones, or other small base stations. The array is based on a dual-band stacked-patch antenna, which can operate simultaneously at 28 and 39 GHz in both polarizations, meeting the fifth-generation (5G) $2\ttimes 2$ polarization multiple-input–multiple-output (MIMO) standard at both frequencies. The array is fabricated on a low-cost printed-circuit board and has a measured effective isotropic radiated power (EIRP) of 27–30 dBm at P1dB with a 3-dB bandwidth of 26.5–29 and 36–40 GHz. The array scans to $\pm$ 40 $^{\circ}$ at 28 GHz and $\pm$ 30 $^{\circ}$ –40 $^{\circ}$ at 39 GHz in the azimuth plane. In simultaneous dual-beam operation at the same band, complex modulation measurement with 64 quadrature amplitude modulation (QAM) 400-Mbaud waveforms shows an error vector magnitude (EVM) of $<$ 5% up to an EIRP of 20 dBm for the V-and H-polarized beams. The array needs to be calibrated at 28-and 39-GHz band separately so is currently incapable of interband carrier aggregation (CA). To the best of authors’ knowledge, this is the first demonstration of a 5G frequency range 2 (FR2) dual-band, dual-polarized active phased array.
In this paper, authors present their work on field-programmable gate array (FPGA) hardware implementation of proposed direction of arrival estimation algorithms employing LU factorization. Both L and U matrices were considered in computing the angle estimates. Hardware implementation was done on a Virtex-5 FPGA and its experimental verification was performed using National Instruments PXI platform which provides hardware modules for data acquisition, RF down-conversion, digitization, etc. A uniform linear array consisting of four antenna elements was deployed at the receiver. LabVIEW FPGA modules with high throughput math functions were used for implementing the proposed algorithms. MATLAB simulations of the proposed algorithms were also performed to validate the efficacy of the proposed algorithms prior to hardware implementation of the same. Both MATLAB simulation and experimental verification establish the superiority of the proposed methods over existing methods reported in the literature, such as QR decomposition-based implementations. FPGA compilation results report low resource usage and faster computation time compared with the QR-based hardware implementation. Performance comparison in terms of estimation accuracy, percentage resource utilization, and processing time is also presented for different data and matrix sizes.