Davide Cittanti

Mr. Davide Cittanti

Politecnico di Torino, Department of Energy
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 May 2022 in IEEE Access
Verified
Journal Article
Open access
Davide CittantiDavide Cittanti
Davide Cittanti
EVEnrico Vico
Enrico Vico
RBRadu Bojoi
Radu Bojoi
The drive inverter represents a central component of an electric vehicle (EV) drive train, being responsible for the DC/AC power conversion between the battery and the electrical machine. In this context, novel converter topologies adopting modern 600/650V wide bandgap (WBG) semiconductor devices will play a crucial role in improving the performance of next-generation drive inverters. In fact, WBG devices theoretically allow to achieve both higher inverter power density and higher conversion efficiency with respect to conventional silicon (Si) IGBT based solutions. Even though silicon carbide (SiC) devices are already well established in the automotive industry, high-voltage gallium nitride (GaN) devices are rapidly entering the market, promising higher theoretical performance but featuring a lower degree of maturity. As a consequence, it is currently not clear which semiconductor technology is most suited for future EV drive inverters. Therefore, this paper aims to address this gap providing a comparative performance evaluation of state-of-the-art SiC and GaN 600/650V active switches. In particular, a novel figure-of-merit (FOM) representing the minimum theoretical semiconductor losses under hard-switching operation is introduced. Remarkably, this FOM enables a fair and accurate performance comparison among semiconductor devices, allowing to clearly determine the best performing technology for a given set of application-specific conditions. The results of the comparative assessment show that currently available SiC and GaN active switch technologies can outperform each other depending on the semiconductor operating temperature and the converter switching frequency.

1 June 2017
Verified
Conference Paper
Closed access
Davide CittantiDavide Cittanti
Davide Cittanti
AFAlessandro Ferraris
Alessandro Ferraris
AAAndrea Giancarlo Airale
Andrea Giancarlo Airale
SFSabina Fiorot
Sabina Fiorot
SSSanto Scavuzzo
Santo Scavuzzo
CMCarello Massimiliana
Carello Massimiliana

22 August 2023 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
Davide CittantiDavide Cittanti
Davide Cittanti
FSFausto Stella
Fausto Stella
EVEnrico Vico
Enrico Vico
CLChaohui Liu
Chaohui Liu
JSJinliang Shen
Jinliang Shen
RBRadu Bojoi
Radu Bojoi
The drive inverter is a crucial component of an electric vehicle (EV) powertrain, being responsible for the DC/AC power conversion between the battery and the electric motor. The increasing demand for lower weight and higher conversion efficiency is opening new challenges, encouraging the adoption of new technologies (e.g., wide bandgap semiconductor devices). In particular, the DC-link capacitor typically represents the bulkiest inverter component, posing a strict limitation to the achievable converter power density and thus being subject to great pressure for improvement. In this context, novel ceramic capacitor technologies (e.g., PLZT) promise superior performance with respect to well established film-based solutions, featuring both higher specific capacitance and higher RMS current capability. Therefore, this paper focuses on the analysis, sizing, design and experimental assessment of a PLZT-based ceramic DC-link capacitor for next-generation EV drive inverters, including a comparative assessment with a state-of-the-art film-based solution. In particular, in view of the non-linear behavior of the PLZT capacitance value with respect to the DC-bias voltage and the amplitude of the excitation, a novel correlation between the effective large-signal capacitance and the peak-to-peak voltage ripple is derived experimentally, providing useful information for the DC-link capacitor sizing (i.e., not available from the capacitor manufacturer). For verification purposes, a full-scale DC-link capacitor prototype for a SiC MOSFET 800 V, 550 kVA, 20 kHz drive inverter is realized, demonstrating superior power density (i.e., $\approx$ two thirds smaller and $\approx$ one third lighter than a corresponding film-based solution). Finally, the inverter prototype is also exploited to validate experimentally the proposed DC-link peak-to-peak voltage ripple estimation procedure, based on the newly obtained large-signal capacitance characterization.

23 January 2021 in World Electric Vehicle Journal
Verified
Journal Article
Open access
PDF file
FMFabio Mandrile
Fabio Mandrile
Davide CittantiDavide Cittanti
Davide Cittanti
Vincenzo MallemaciVincenzo Mallemaci
Vincenzo Mallemaci
RBRadu Bojoi
Radu Bojoi
As a consequence of the exponential growth of the electric vehicle (EV) market, DC fast-charging infrastructure is being rapidly deployed all around the world. Ultra-fast charging (UFC) stations are starting to pose serious challenges to the electric power system operation, mostly due to their high peak power demand and unregulated discontinuous operation. To address these issues, local energy storage can be installed, ensuring a smoother grid power absorption profile and allowing to provide grid-supporting features. In this work, a control solution for the grid-side AC/DC converter of next-generation EV UFC stations is proposed. A virtual synchronous compensator (VSC) control algorithm is implemented, in order to lessen the impact of the charging station on the utility and to provide the full spectrum of grid ancillary services (i.e., frequency regulation, reactive power compensation, harmonic reduction, short circuit current generation, etc.). The proposed control strategy is verified experimentally on a downscaled 15 kVA three-phase inverter, emulating the grid front-end of the charging station.

24 November 2020
Verified
Conference Paper
Closed access
Davide CittantiDavide Cittanti
Davide Cittanti
MGMattia Guacci
Mattia Guacci
SMSpasoje Miric
Spasoje Miric
RBRadu Bojoi
Radu Bojoi
JKJohann W. Kolar
Johann W. Kolar

1 October 2017
Verified
Conference Paper
Closed access
Davide CittantiDavide Cittanti
Davide Cittanti
FRANCESCO IANNUZZOFRANCESCO IANNUZZO
FRANCESCO IANNUZZO
EHEckart Hoene
Eckart Hoene
KKKirill Klein
Kirill Klein
This paper describes the effect of MOSFET internal capacitances on the channel current during the turn-on switching transition: an intrinsic theoretical switching speed limit is found and detailed mathematically. The set of analytical equations is solved and the effect of the displacement currents is highlighted with ideal simulated waveforms. A laboratory experiment is thus performed, in order to prove the theoretical predictions: a 25 mΩ SiC CREE power MOSFET is turned on in a no-load condition (zero drain current), starting from different drain-source voltage values. Finally, a LTSpice equivalent circuit model is also built, to better simulate the experimental behavior of the device, adding circuit strain components and other non-idealities to the overall model. A good match between measurements and simulations is observed, mostly validating either the theoretical assumptions and the presented model.