Juan R. García-Meré

Mr. Juan R. García-Meré

Universidad de Oviedo, Gijón, Asturias, Spain
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
Juan RodriguezJuan Rodriguez
Juan Rodriguez
JGJuan R. García-Meré
Juan R. García-Meré
Daniel G. AllerDaniel G. Aller
Daniel G. Aller
Javier SebastianJavier Sebastian
Javier Sebastian
Envelope tracking is a well-known RF technique that alleviates the efficiency problem of linear power amplifiers used in wireless communication transmitters. It consists in varying the supply voltage of the amplifier, which is commonly constant, according to the envelope of the communication signal. Therefore, a switching-mode power converter with a bandwidth of several megahertz is required to perform the fast voltage changes needed for tracking the envelope properly. Another important requirement is that the converter needs to be able to achieve high efficiency not only at peak output power, but also at low output power because it operates in that power range most of the time due to the characteristics of modern communication signals. Taking into account these requirements, the design of the converter is very challenging, especially in the case of base stations, where higher power levels are reached by means of higher voltage levels. As a result, transistors with low breakdown voltages (20–30 V), which offer the highest speed, cannot be used in the converter. In this article, a novel multilevel converter able to use transistors with low breakdown voltages is proposed to alleviate that problem. Moreover, it shows a better switching behavior than the previously proposed multilevel converters, thus reducing the switching losses and, consequently, increasing the efficiency. In order to experimentally validate the proposed topology, a 73-W prototype with a switching frequency of 8 MHz was built. The efficiency is 94% and 81.7% at peak output power and at one-tenth of peak output power, respectively.

20 November 2023 in IEEE Access
Verified
Journal Article
Open access
Juan RodriguezJuan Rodriguez
Juan Rodriguez
JGJuan R. García-Meré
Juan R. García-Meré
Diego G. LamarDiego G. Lamar
Diego G. Lamar
Marta M. HernandoMarta M. Hernando
Marta M. Hernando
Javier SebastianJavier Sebastian
Javier Sebastian
Incorporating switched-capacitor structures into isolated dc-dc converters is a promising approach to alleviate the limitations of topologies fully based on the use of high step-down transformers. In this paper, the combination of a forward converter with a series-capacitor structure is proposed for applications that require a very high step-down conversion ratio, low output voltage ripple, high output current and isolation. The result of the combination only adds one series-capacitor, one inductor, one switch and one diode (or synchronous rectifier switch) to the component count of a conventional forward converter, thus avoiding the use of a complete second phase. The topology provides high step-down conversion ratio and low output voltage ripple, a characteristic that can be used to decrease the total energy stored by inductors (i.e., higher power density) and/or to reduce the switching frequency (i.e., higher efficiency). Moreover, the converter provides inherent current sharing between the two inductors, natural balance of the voltage across the series-capacitor and lower conduction losses. The converter operation is validated with a 100W and 48V-to-5/3.3/2.5/1.8V prototype that achieves a peak efficiency of 95.8% and a full load efficiency of 91.1%.

1 December 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
Juan RodriguezJuan Rodriguez
Juan Rodriguez
JGJuan R. García-Meré
Juan R. García-Meré
Diego G. LamarDiego G. Lamar
Diego G. Lamar
Javier SebastianJavier Sebastian
Javier Sebastian
Visible Light Communication (VLC) has recently emerged as a promising technology for alleviating the saturation of the Radio Frequency (RF) spectrum. VLC uses High-Brightness LEDs (HB-LEDs) both for lighting and for communication. In particular, the information transmission is carried out by performing fast changes of the light intensity emitted by the HB-LEDs. The conventional VLC driver includes a Linear Power Amplifier (LPA) for reproducing the communication signal. Unfortunately, that approach penalizes the efficiency. During the last years, a wide variety of VLC drivers fully based on the use of Switching-Mode Power Converters (SMPCs) has been proposed to overcome the efficiency limitation. One of the most promising approaches is the Ripple-Modulation (RM) technique, which consists in using the output voltage ripple of a SMPC to reproduce the communication signal. However, the conventional RM technique has a major drawback: it can only be applied to multi-phase buck converters. This work is focused on overcoming that limitation by introducing a novel version of the RM technique that enables the use of a single-phase buck converter. In this way, the work aims to reduce the required power-stage complexity, which is a critical parameter of HB-LED bulbs. Moreover, a novel output filter structure is proposed to reduce the total harmonic distortion of the reproduced signal. A ripple-modulated buck converter prototype was built with an output power and a switching frequency of 8 W and 2 MHz, respectively. Moreover, the reproduced passband modulation scheme provides a bit rate up to 1.25 Mbps with a communication range of 100 cm and a peak efficiency of 94%.

14 October 2024 in Sensors
Verified
Journal Article
Open access
PDF file
FLFelipe Loose
Felipe Loose
JGJuan R. García-Meré
Juan R. García-Meré
ARAdrion Andrei Rosanelli
Adrion Andrei Rosanelli
CBCarlos Henrique Barriquello
Carlos Henrique Barriquello
JAJose Antonio Fernandez Alvarez
Jose Antonio Fernandez Alvarez
Diego G. LamarDiego G. Lamar
Diego G. Lamar
This paper presents a dual-purpose LED driver system that functions as both a lighting source and a Visible Light Communication (VLC) transmitter integrated with a Powerline Communication (PLC) network under the PRIME G3 standard. The system decodes PLC messages from the powerline grid and transmits the information via LED light to an optical receiver under a binary phase shift keying (BPSK) modulation. The load design targets a light flux of 800 lumens, suitable for LED light bulb applications up to 10 watts, ensuring practicality and energy efficiency. The Universal Asynchronous Receiver-Transmitter (UART) module enables communication between the PLC and VLC systems, allowing for an LED driver with dynamic control and real-time operation. Key signal processing stages are commented and developed, including a hybrid buck converter with modulation capabilities and a nonlinear optical receiver to regenerate the BPSK reference signal for VLC. Results show a successful prototype working under a laboratory environment. Experimental validation shows successful transmission of bit streams from the PLC grid to the VLC setup. A design guideline is presented in order to dictate the design of the electronic devices involved in the experiment. Finally, this research highlights the feasibility of integrating PLC and VLC technologies, offering an efficient and cost-effective solution for data transmission over existing infrastructure.

2 October 2024 in Sensors
Verified
Journal Article
Open access
PDF file
Daniel G. AllerDaniel G. Aller
Daniel G. Aller
Diego G. LamarDiego G. Lamar
Diego G. Lamar
JGJuan R. García-Meré
Juan R. García-Meré
MAManuel Arias
Manuel Arias
Juan RodriguezJuan Rodriguez
Juan Rodriguez
Javier SebastianJavier Sebastian
Javier Sebastian
This work proposes a high-efficiency High-Brightness LED (HB-LED) driver for Visible Light Communication (VLC) based on a Two-Input Buck (TIBuck) DC/DC converter. This solution not only outperforms previous approaches based on Buck DC/DC converters, but also simplifies previous proposals for VLC drivers that use the split power technique with two DC/DC converters: one is in charge of the communication tasks and the other controls the biasing of the HB-LED (i.e., lighting tasks). The real implementation of this scheme requires either two input voltage sources, one of which is isolated, or one DC/DC converter with galvanic isolation. The proposed implementation of splitting the power is based on a TIBuck DC/DC converter that avoids the isolation requirement, overcoming the major drawback of this technique, keeping high-efficiency and high communication capability thanks to the lower voltage stress both across the switches and at the switching node. This fact allows for the operation at very high frequency for communication purposes, minimizing switching power losses, achieving high efficiency and providing lower filtering effort. Moreover, the duty ratio range can also be adapted to the useful voltage range of the HB-LED load to maximize the resolution on the tracking of the output volage. The power is split by means of an auxiliary Buck DC/DC converter operating at low switching frequency, which generates the secondary voltage source needed by the TIBuck DC/DC converter. This defines a natural split of power by only processing the power delivered for communications purposes at high frequency. A 7 W output-power experimental prototype of the proposed VLC driver was built and tested. Based on the experimental results, the prototype achieved 94% efficiency, reproducing a 64-QAM digital modulation scheme and achieving a bit rate of 1.5 Mbps with error in communication of 12%.

27 June 2022 in Sensors
Verified
Journal Article
Open access
PDF file
JGJuan R. García-Meré
Juan R. García-Meré
Juan RodriguezJuan Rodriguez
Juan Rodriguez
Diego G. LamarDiego G. Lamar
Diego G. Lamar
Javier SebastianJavier Sebastian
Javier Sebastian
Visible Light Communication (VLC) is a wireless communication technology that uses visible light to transmit information. The most extended implementation of a VLC transmitter employs a DC-DC power converter that biases the High-Brightness LEDs (HB-LEDs), and a Linear Power Amplifier (LPA) that reproduces the communication signal. Unfortunately, the power efficiency of LPAs is very low, thus reducing the overall system efficiency and requiring huge cooling systems to extract the heat. In this work, the use of Class D Switching-Mode Power Amplifiers (SMPAs) is explored in order to overcome that limitation. It is important to note that this SMPA is widely used for different applications, such as audio and RF power amplifiers. Therefore, there are a lot of versions of a Class D SMPA depending on the topology used for the implementation and the modulation strategy used to control the switches. Hence, this work aims to identify, adapt and explain in detail the best approach for implementing a Class D SMPA for VLC. In order to validate the proposed idea, a power-efficient VLC transmitter intended for short-range and low-speed applications was built and evaluated.