In the present scenario, the research is now being focused on the naturally occurring polymers that can gradually replace the existing synthetic polymers for the development of bio composites having applications in medical surgeries and human implants. With promising mechanical properties and bio compatibility with human tissues, poly lactic acid (PLA) is now being viewed as a future bio material. In order to examine the applicability of PLA in human implants, the current article sheds light on the synthesis of PLA and its various copolymers used to alter its physical and mechanical properties. In the latter half, various processes used for the fabrication of biomaterials are discussed in detail. Finally, biomaterials that are currently in use in the field of biomedical (Scaffolding, drug delivery, tissue engineering, medical implants, derma, cosmetics, medical surgeries, and human implants) are represented with respective advantages in the sphere of biomaterials.
Heavy metal toxicity in water is a serious problem that may have harmful effects on human health and the ecosystem. Lead [Pb(II)] and cadmium [Cd(II)] are two such heavy metal ions, present in water, whose severity is well-known and well-studied. In the current research, magnetic biochar composite (MBC) is studied as an adsorbent material for the effective removal of lead and cadmium ions from water solutions. Magnetite (Fe3O4) nanoparticles and pine-needle-derived ultrasonicated magnetic biochar were used in different weight ratios to prepare APTES (3-aminopropyl triethoxysilane)-functionalized MBC (FMBC). An average crystalline size of ~10 nm for magnetite NPs was obtained via XRD analysis. The adsorption characteristics of both Pb(II) and Cd(II) ions were investigated in a batch experiment. The FTIR spectra of raw biochar, MBC, FMBC, and metal-loaded FMBC were obtained at different stages. The decrease in the intensity of the –NH2 functional group in the FTIR spectra of the residue confirmed the successful adsorption of heavy metal ions. The SEM-EDX spectra of the residue showed the uniform adsorption of Pb(II) and Cd(II) heavy metal ions onto the surface of the adsorbent. Magnetic biochar composite (MBC) was found to be a very effective adsorbent at basic pH, as a maximum of 97% instantaneous heavy metal removal was observed for both ions in synthetic water solutions. The Langmuir isotherm model predicted the monolayer adsorption and good affinity between the metal ions and adsorbent. The prepared MBC is low-cost, environmentally friendly, and it has shown good adsorption performance. Therefore, our study suggests that the magnetic biochar composite under study is an effective adsorbent for lead and cadmium metal ion removal from aqueous solutions at normal room temperature. Only a few hundred milligrams of the adsorbent dose is sufficient to remove higher concentrations (~100 ppm) of lead and cadmium at basic pH conditions of aqueous solutions.
Evacuated tube solar water heaters are gaining more attention in the present market scenario as compared to conventional collectors. Such collectors are versatile because no solar tracking is required and the operating temperature range is also broad. Comparatively, it is cost-effective and may attain higher thermal efficiency. However, like other collectors, continuous energy supply is sometimes hampered by the intermittent nature of solar radiation. This problem can be partially resolved by using phase change materials (PCM) in the evacuated tube solar collector (ETC). PCMs can store the energy during the sunshine hours, which can be released when solar energy is not available. In the literature, several studies are available pertaining to the use of PCMs in ETC-based solar water heaters. The literature indicates that the integration of PCMs with ETCs has several merits. Nevertheless, systematic, and comprehensive review papers dedicated to such integrated energy storage systems with ETC solar water heaters are not available. Hence, the objective of this work is to compile the relevant experimental, numerical, and theoretical works reported in the literature. The present paper broadly reviews the recent design modifications, PCM integration with different kinds of ETC water heaters, and their life cycle assessment. Furthermore, studies in the literature pertaining to the application of nanoparticles in ETC systems are also discussed, and finally, a roadmap for this energy storage system is provided.
1 June 2024 in International Journal of Thermal Sciences
In this paper, numerical analysis has been performed on micro-pin fin heat sinks with novel arrangements of the fins. Varying the fin height in an array of two, three, and four fins evolves stepped-type pin fin heat sink. Geometry selection of all seven configurations of the heat sinks is made on the basis of equal footprint area as well as net convective surface area. Single-phase liquid water has been used as a cooling medium where inlet Reynolds number (Re) varied from 200-600. Comparative numerical results are presented through the illustration of temperature distribution, Nusselt number (Nu), pressure drop, velocity contour, and thermal performance factor. Estimated findings clearly indicate that the overall performance of the stepped configurations is better than uniform fin height. Moreover, arrays of increasing fin heights facilitate favorable flow behavior compared to decreasing fin height; consequently, they support higher heat transfer rate from the heat sink. Among the stepped heat sinks, THSI (three-stepped increasing) configuration exhibits superior performance due to distinct coolant flow and favorable heat dissipation circumstances originated by constructive fin arrangements. Similarly, the thermal performance factor of THSI is found to be consistently higher compared to all other heat sinks.
High heat flux dissipation from the Lithium-ion battery pack of hybrid electric vehicles is one of the major concerns in the automotive sector, since it directly affects the performance and it may also lead to permanent failure. Among various thermal management systems, forced air cooling is most favorable due to its light weight, compactness, lower cost, and design flexibility. In the present work, a battery thermal management system with the two types of vortex generator in the coolant passage has been used to enhance the performance. A numerical model has been developed in commercial code to investigate the performance of the delta winglet and circular protrusion type vortex generator. Apart from that, both types of vortex generator have been compared in terms of various parameters such as pressure drop, weight, and maximum temperature. From the results of the simulation, it has been observed that both vortex generators performed better at the attack angle of 30° in comparison to the attack angles of 45° and 60°. Furthermore, it has also been found that the cooling system with protrusion as the vortex generator has performed better in terms of thermos-hydraulic performance compared to the cooling system with the delta winglet vortex generator. In addition to that, the protruded system is lighter in weight compared to both the plain and delta winglet systems, and is recommended.