The paper considers the issues of maintaining an equality of flow in generated and consumed electric energy in an electric network incorporating an electric power storage system. An analysis of ways to equalize the energy and power balance was carried out, and the advantages of using electricity storage systems in electrical networks was assessed. Upon simulation using the Power Factory program, we noted that, after switching on the load, a transient process occurs, characterized by a jump in active power, which was caused by the need for time to initiate the electric energy storage system. However, immediately after this, the process of issuing the accumulated energy to the electrical network and compensating for energy consumption began. Moreover, when the load was disconnected, there is a certain dip in the active power curve and a further increase in consumption. This was found to be due to the transition of the electricity storage system to the modes of energy storage and battery charging. As a result of this simulation, data on the charging and discharging time of the electricity storage system were obtained. The studies show that the use of electricity storage systems in electrical networks allows for the stable operation of all main generators, and thus increases the safety and reliability of the entire system.
During the design of extra-high-voltage transmission lines, studies of the influence of asymmetry due to the phase difference of the parameters on its processes and the electrical network were performed. To compensate for this source of asymmetry for transmission lines longer than 100 km, a relatively simple technical means was proposed and implemented—phase transposition (change of the mutual location of phase wires in space). However, at the same time transposition causes additional capital costs in construction and reduces reliability during operation, so when designing a specific transmission line, extra-high-voltage is desirable to evaluate the effectiveness of the use of this measure in the real electricity network. Thus, under certain conditions, even for a transmission line 600 km in length, it was possible to perform either an incomplete transposition cycle, or abandon this measure altogether.
Wydawnictwo SIGMA-NOT wydaje czasopisma fachowe informujące swoich czytelników o najnowszych osiągnięciach naukowych i nowoczesnych rozwiązaniach technicznych w Polsce i na świecie, popularyzuje problemy techniczne oraz poszerza wiedzę i kulturę techniczną.
The article discusses the selection of cables for power lines connecting wind turbine generators at the wind power plant. The screen cross-section of these cables should be selected considering the value of the screen current at double line-to-earth fault. To calculate this current, the dimensions of the cable should be known. However, these parameters are hidden and cannot be used during designing. Therefore, a highly simplified method is currently used in practice. It is shown that the errors from the highly simplified method are up to 33%. Authors propose a simplified method based on open data of cable manufacturers. The proposed method is compared with simulation results of a common model of cable power line and takes into account self and mutual inductances of the cores and screens. It is shown that the error of the proposed method is smaller than 4.0% for real cable power lines at wind power plants. However, for a long section of cable power line (2.5 km) the error of calculation might increase up to 6.3%. This allows us to use the proposed method for designing. In addition, the authors show how the results of the highly simplified method can be corrected to improve accuracy.
1 December 2020 in International Journal of Power Electronics and Drive Systems (IJPEDS)
In the article the circuit design solution of DC-DC regulated resonant converter has been proposed for using with hybrid photovoltaic modules which has cooling equipment and solar concentrators in order to maximize electric power generating by such module. By using computer simulation based on multiple iterations algorithm we significantly increase the accuracy of determining the resonance circuit optimal parameters for build up DC–DC converters to work in a wide range of electric powers. Based on optimal values of the resonance LLC scheme parameters, achived by numerical calculation it can be show high values of electrical energy transformation efficiency for photovoltaic energy station equipped with high efficiency hybrid photovoltaic modules. Implementation of microprocessor-based control into design of DC–DC back-boost converters create a new possibility to build control algorithms for increase reliability and conversion efficiency, rapid and precision stabilization of maximum power point, implementation network monitoring of photovoltaic modules, converters itself and the whole photovoltaic station parameters.
The aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity of 2.5 MW. A general scheme of a wind power plant has been developed using a modular-trunk power distribution scheme. The system consists of wind power modules and a central substation, which allows total power to be supplied to the power system at a voltage of 35 kV. The central substation uses two high voltage switchgears. Four modules were used, each of them consisting of three wind turbines, with a power of 7.5 MW. The simulation of the wind turbines was performed in the MATLAB® Simulink® software environment. The mode of response of the turbines to a change in wind speed, a voltage drop in the 35 kV voltage system, and a one-phase short circuit to the ground in the system of 10.5 kV voltage was explored. The results show that a sudden voltage drop and the appearance of short circuits influence the wind power plant (WPP) operation in a different way independent of regulation mode. The power generation from WPP will be limited when voltage drop occurred for both AC and Voltage regulation mode and during short circuits while WPP is set on AC regulation mode.