Hans Peter Monner

Prof. Dr. Hans Peter Monner

Institute of Composite Structures and Adaptive Systems, German Aerospace Center, 38108 Brunswick, Germany
orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 October 2019 in Aerospace
Verified
Journal Article
Open access
PDF file
SVSrinivas Vasista
Srinivas Vasista
JRJohannes Riemenschneider
Johannes Riemenschneider
RKRalf Keimer
Ralf Keimer
HMHans Peter Monner
Hans Peter Monner
FNFelix Nolte
Felix Nolte
PHPeter Horst
Peter Horst
A design for a new high lift system that features a morphing wing leading edge “droop nose” has the potential to generate high lift coefficients whilst mitigating airframe noise emissions. This seamless, continuous, and stepless flexible droop nose potentially offers improvements to stall and compressor requirements for an internally-blown active Coandă trailing edge flap. A full-scale, span-trimmed three-dimensional droop nose was manufactured and ground-tested based on results obtained from new design synthesis tools. A new component of the droop nose is the hybrid fiberglass-elastomeric skin that is tailored in stiffness to meet morphing curvature requirements and spanwise bending resistance. A manufacturing concept of the novel skin was established that led to an adequate manufacturing quality. The skin was driven and supported by two optimized kinematic ribs and conventional actuators and overall shape results show good agreement apart from the region closest to the leading edge. Kinematic trajectory measurements showed that the kinematics met the target trajectories well, with and without the influence of the skin, and it was deemed that the error in curvature is due to a higher than expected skin stiffness in the hybrid layer. Calculated actuator torque levels and strain measurements corroborate this inference. The lessons learned show that means of adjustment post-assembly are needed, and a reduction of torque, energy and a better curvature distribution may be achieved if the skin at the spar junction is allowed to move relative to the main wing. Careful aerodynamic, structural, actuation and manufacturing trade-off studies would be needed to determine the overall performance benefit.

14 September 2005 in Proceedings of the 37th International Symposium on Automation and Robotics in Construction (isarc)
Verified
Conference Paper
Closed access
SAStephan Algermissen
Stephan Algermissen
RKRalf Keimer
Ralf Keimer
MRMichael Rose
Michael Rose
EBElmar Breitbach
Elmar Breitbach
HMHans Peter Monner
Hans Peter Monner
I.A.A.R.C. - International Association for Automation and Robotics in Construction Civil Engineering

1 October 2021 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
MSMaximilian Otto Heinrich Schutzeichel
Maximilian Otto Heinrich Schutzeichel
TKThomas Kletschkowski
Thomas Kletschkowski
HMHans Peter Monner
Hans Peter Monner
Polymer electrolyte coated carbon fibres embedded in polymeric matrix materials represent a multifunctional material with several application scenarios. Structural batteries, thermal management materials as well as stiffness adaptive composites, made from this material, are exposed to significant joule heat, when electrical energy is transferred via the carbon fibres. This leads to a temperature increase of up to 100 K. The thermal behaviour of this composite material is characterized in this numerical study based on a RVE representation for the first time. Compared to classical fibre reinforced plastics, this material comprises a third material phase, the polymer electrolyte coating, covering each individual fibre. This material has not been evaluated for effective thermal conductivity, specific heat and thermal behaviour on the microscale before. Therefore, boundary conditions, motivated from applications, are applied and joule heating by the carbon fibres is included as heat source by an electro-thermal coupling. The resulting temperature field is discussed towards its effect on the mechanical behaviour of the material. Especially the temperature gradient is pronounced in thickness direction, leading to a temperature drop of 1 °Cmm, which needs to be included in thermal stress analysis in future thermo-mechanically coupled models. Another important emphasis is the identification of suitable homogenization and model reduction strategies in order to reduce the numerical effort spent on the thermal problem. Therefore, traditional analytical homogenization methods as well as a newly proposed “Two-Level Lewis-Nielsen” approach are discussed in comparison to virtually measured effective quantities. This extensive comparison of analytical and numerical methods is original compared to earlier works dealing with PeCCF composites. In addition, the accuracy of the new Two-Level Lewis-Nielsen method is found to fit best compared to classical methods. Finally, a first efficient and accurate 2D representation of the thermal behaviour of the PeCCF composite is shown, which reduces computational cost by up to 97%. This benefit comes with a different Temperature drop prediction in thickness direction of 1.5 °Cmm. In the context of future modelling of multifunctional PeCCF composite materials with multiphysical couplings, this deviation is acceptable with respect to the huge benefit for computational cost.

2 January 2015
Verified
Conference Paper
Closed access
HMHans Peter Monner
Hans Peter Monner
OHOliver Huxdorf
Oliver Huxdorf
JRJohannes Riemenschneider
Johannes Riemenschneider
RKRalf Keimer
Ralf Keimer


20 January 2026 in CEAS Aeronautical Journal
Verified
Journal Article
Open access
PDF file
FKFelix Kleinwechter
Felix Kleinwechter
ANAhmad Naderi
Ahmad Naderi
AMAbbas Mehraban
Abbas Mehraban
TRThomas Ruminy
Thomas Ruminy
MSMarcel Seidler
Marcel Seidler
JFJens Friedrichs
Jens Friedrichs
The blades of modern aero-engines are conceived for a specific design point. Due to the resulting fixed geometry of the blade, maximum engine efficiency can be achieved only for design point conditions. In order to improve the efficiency during off-design operation, applying blades with active shape control can be beneficial. Therefore, morphing fan blades, which adapt their geometry to the prevailing conditions by using piezoelectric low-profile actuators, are researched. Prior to the construction of a morphing fan blade demonstrator, a sequential multidisciplinary analysis is required to assess the feasibility of piezoelectric actuation in fan blades of future aircraft. First, the aerodynamic geometry of the fan blade is designed with respect to maximising the deformability. Subsequently, the structure of the morphing blade is developed, including a drapability analysis of the actuators and a numerical simulation of the achievable morphing deformation. Finally, the developed morphing structure is employed to examine a sufficient electrical power supply system for the morphing technology in a future electrified aircraft.