A surface sensitivity study was performed on different transition-metal dichalcogenides (TMDs) under ambient conditions in order to understand which material is the most suitable for future device applications. Initially, Atomic Force Microscopy and Scanning Electron Microscopy studies were carried out over a period of 27 days on mechanically exfoliated flakes of 5 different TMDs, namely, MoS2, MoSe2, MoTe2, HfS2, and HfSe2. The most reactive were MoTe2 and HfSe2. HfSe2, in particular, showed surface protrusions after ambient exposure, reaching a height and width of approximately 60 nm after a single day. This study was later supplemented by Transmission Electron Microscopy (TEM) cross-sectional analysis, which showed hemispherical-shaped surface blisters that are amorphous in nature, approximately 180–240 nm tall and 420–540 nm wide, after 5 months of air exposure, as well as surface deformation in regions between these structures, related to surface oxidation. An X-ray photoelectron spectroscopy study of atmosphere exposed HfSe2 was conducted over various time scales, which indicated that the Hf undergoes a preferential reaction with oxygen as compared to the Se. Energy-Dispersive X-Ray Spectroscopy showed that the blisters are Se-rich; thus, it is theorised that HfO2 forms when the HfSe2 reacts in ambient, which in turn causes the Se atoms to be aggregated at the surface in the form of blisters. Overall, it is evident that air contact drastically affects the structural properties of TMD materials. This issue poses one of the biggest challenges for future TMD-based devices and technologies.
Platinum diselenide (PtSe2) is a group-10 transition metal dichalcogenide (TMD) that has unique electronic properties, in particular a semimetal-to-metal transition when going from bulk to monolayer form. We report on vertical hybrid Schottky barrier diodes (SBDs) of two-dimensional (2D) PtSe2 thin films on crystalline n-type silicon. The diodes have been fabricated by transferring large-scale layered PtSe2 films, synthesized by thermally assisted conversion at back-end-of-the-line CMOS compatible temperatures of pre-deposited Pt films. The diodes exhibit good rectifying behavior with a clear photoresponse under illumination. Spectral response analysis reveals a considerable responsivity of the SBDs due to photon-induced charge carriers in the silicon region. In addition, we demonstrate that PtSe2 can be utilized as an absorber of infrared light with tunable sensitivity. The results of our study indicate that PtSe2 is a promising option for the development of infrared absorbers and detectors for optoelectronics applications, in particular given its good stability and low temperature processing options.
3 September 2019 in npj 2D Materials and Applications
In this work, we present a comprehensive theoretical and experimental study of quantum confinement in layered platinum diselenide (PtSe2) films as a function of film thickness. Our electrical measurements, in combination with density functional theory calculations, show distinct layer-dependent semimetal-to-semiconductor evolution in PtSe2 films, and highlight the importance of including van der Waals interactions, Green’s function calibration, and screened Coulomb interactions in the determination of the thickness-dependent PtSe2 energy gap. Large-area PtSe2 films of varying thickness (2.5–6.5 nm) were formed at 400 °C by thermally assisted conversion of ultra-thin platinum films on Si/SiO2 substrates. The PtSe2 films exhibit p-type semiconducting behavior with hole mobility values up to 13 cm2/V·s. Metal-oxide-semiconductor field-effect transistors have been fabricated using the grown PtSe2 films and a gate field-controlled switching performance with an ION/IOFF ratio of >230 has been measured at room temperature for a 2.5–3 nm PtSe2 film, while the ratio drops to <2 for 5–6.5 nm-thick PtSe2 films, consistent with a semiconducting-to-semimetallic transition with increasing PtSe2 film thickness. These experimental observations indicate that the low-temperature growth of semimetallic or semiconducting PtSe2 could be integrated into the back-end-of-line of a silicon complementary metal-oxide-semiconductor process.
10 January 2020 in ACS Applied Materials & Interfaces
Platinum diselenide (PtSe2) field‐effect transistors with ultrathin channel regions exhibit p‐type electrical conductivity that is sensitive to temperature and environmental pressure. Exposure to a supercontinuum white light source reveals that positive and negative photoconductivity coexists in the same device. The dominance of one type of photoconductivity over the other is controlled by environmental pressure. Indeed, positive photoconductivity observed in high vacuum converts to negative photoconductivity when the pressure is raised. Density functional theory calculations confirm that physisorbed oxygen molecules on the PtSe2 surface act as acceptors. The desorption of oxygen molecules from the surface, caused by light irradiation, leads to decreased carrier concentration in the channel conductivity. The understanding of the charge transfer occurring between the physisorbed oxygen molecules and the PtSe2 film provides an effective route for modulating the density of carriers and the optical properties of the material.
8 January 2021 in npj 2D Materials and Applications
The properties and performance of two-dimensional (2D) materials can be greatly affected by point defects. PtTe2, a 2D material that belongs to the group 10 transition metal dichalcogenides, is a type-II Dirac semimetal, which has gained a lot of attention recently due to its potential for applications in catalysis, photonics, and spintronics. Here, we provide an experimental and theoretical investigation of point defects on and near the surface of PtTe2. Using scanning tunneling microscopy and scanning tunneling spectroscopy (STS) measurements, in combination with first-principle calculations, we identify and characterize five common surface and subsurface point defects. The influence of these defects on the electronic structure of PtTe2 is explored in detail through grid STS measurements and complementary density functional theory calculations. We believe these findings will be of significance to future efforts to engineer point defects in PtTe2, which is an interesting and enticing approach to tune the charge-carrier mobility and electron–hole recombination rates, as well as the site reactivity for catalysis.