Hard carbon thin films were synthesized on Si (100) and quartz substrates by the Pulsed Laser Deposition (PLD) technique in vacuum or methane ambient to study their suitability for applications requiring high mechanical resistance. The deposited films’ surface morphology was investigated by scanning electron microscopy, crystalline status by X-ray diffraction, packing and density by X-ray reflectivity, chemical bonding by Raman and X-ray photoelectron spectroscopy, adherence by “pull-out” measurements and mechanical properties by nanoindentation tests. Films synthesized in vacuum were a-C DLC type, while films synthesized in methane were categorized as a-C:H. The majority of PLD films consisted of two layers: one low density layer towards the surface and a higher density layer in contact with the substrate. The deposition gas pressure played a crucial role on films thickness, component layers thickness ratio, structure and mechanical properties. The films were smooth, amorphous and composed of a mixture of sp³-sp² carbon, with sp³ content ranging between 50% and 90%. The thickness and density of the two constituent layers of a film directly determined its mechanical properties.

Laser melting deposition is a 3D printing method usually studied for the manufacturing of machine parts in the industry. However, for the medical sector, although feasible, applications and actual products taking advantage of this technique are only scarcely reported. Therefore, in this study, Ti6Al4V orthopedic implants in the form of plates were 3D printed by laser melting deposition. Tuning of the laser power, scanning speed and powder feed rate was conducted, in order to obtain a continuous deposition after a single laser pass and to diminish unwanted blown powder, stuck in the vicinity of the printed elements. The fabrication of bone plates is presented in detail, putting emphasis on the scanning direction, which had a decisive role in the 3D printing resolution. The printed material was investigated by optical microscopy and was found to be dense, with no visible pores or cracks. The metallographic investigations and X-ray diffraction data exposed an unusual biphasic α+β structure. The energy dispersive X-ray spectroscopy revealed a composition very similar to the one of the starting powder material. The mapping of the surface showed a uniform distribution of elements, with no segregations or areas with deficient elemental distribution. The in vitro tests performed on the 3D printed Ti6Al4V samples in osteoblast-like cell cultures up to 7 days showed that the material deposited by laser melting is cytocompatible.

Carbon thin films of 50–100 nm thickness were synthesized by Pulsed Laser Deposition in vacuum at different laser fluences from 2 to 6 J/cm². The deposited films were characterized by Raman spectroscopy for compositional assessment, scanning electron microscopy for morphology/thickness evaluations, and X-ray reflectivity for density, thickness, and roughness determinations. The films were ~100 nm thin, smooth, droplet-free, made of a-C:H type of diamond-like carbon. The mechanical properties of synthesized films were studied by nanoindentation and adhesion tests. The films that were obtained at low laser fluences (2, 3 J/cm²) had better mechanical properties as compared to those synthesized at higher fluences. The mean values of hardness were around 20 GPa, while the friction coefficient was 0.06. The deposition conditions of carbon thin films that displayed the best mechanical properties were further used to coat commercial drills. Both uncoated and coated drills were tested on plates that were made of three types of steel: Stainless steel 304, general use AISI 572 Gr 65 steel (OL60), and AISI D3 tool steel (C120). All of the drill edges and tips were studied by optical and scanning electron microscopes. The coated samples were clearly found to be more resistant, and displayed less morphological defects than their uncoated counterparts when drilling stainless steel and OL60 plates. In the case of C120 steel, carbon coatings failed because of the high friction between drill and the metal plate resulting in tip edges blunting that occurred during processing.

MAX phase compounds offer an attractive mixture of ceramic–metallic properties due to their covalent ionic–metallic nature. Since their discovery, a great interest was attributed to their synthesis and potential applications, but the processing of pure compounds as coatings for industrial large-scale application is still considered a challenge. To date, a limited number of papers have evaluated the build-up of MAX phase coating by cold spray (CS), a novel cost-effective and productive spray technology used in both areas of research and industry. Employing CS, the hot gas-propelled material particles have ballistic impingement on a substrate where they undergo plastic deformation. Because of the brittleness, internal delamination, and limited deformability, the deposition of the pure MAX phase is rather challenging. This paper presents the building-up ability of dense MAX-phase coatings by CS with retained structures and compositions, in close relation with the substrate characteristics and phase composition that influences the dual character ceramic–metallic behaviour. Besides recent literature, the originality of this research consists of pioneering deposition of Ti₃AlC₂ that emphasizes the ceramic–metallic character influenced by the particle speed and the mechanical properties of both substrate and compound.

We explored the potential of biomimetic thin films fabricated by means of matrix-assisted pulsed laser evaporation (MAPLE) for releasing combinations of active substances represented by flavonoids (quercetin dihydrate and resveratrol) and antifungal compounds (amphotericin B and voriconazole) embedded in a polyvinylpyrrolidone biopolymer; the antifungal activity of the film components was evaluated using in vitro microbiological assays. Thin films were deposited using a pulsed KrF* excimer laser source which were structurally characterized using atomic force microscopy (AFM) and Fourier transform infrared spectroscopy (FTIR). High-quality thin films with chemical structures similar to dropcast ones were created using an optimum laser fluence of ~80 mJ/cm². Bioactive substances were included within the polymer thin films using the MAPLE technique. The results of the in vitro microbiology assay, which utilized a modified disk diffusion approach and were performed using two fungal strains (Candida albicans American Type Culture Collection (ATCC) 90028 and Candida parapsilosis American Type Culture Collection (ATCC) 22019), revealed that voriconazole was released in an active form from the polyvinylpyrrolidone matrix. The results of this study show that the MAPLE-deposited bioactive thin films have a promising potential for use in designing combination products and devices, such as drug delivery devices, and medical device surfaces with antifungal activity.