This study investigated the polymer film composite of polyvinyl alcohol (PVA), trichlorethylene (TCE) and cresol red (CR) dye irradiated with gamma (γ) rays for potential application as radiation dosimetry. The film was prepared via the solvent-casting method with varying concentrations of TCE. Film samples were exposed to radiation from a γ-rays radiation source of 60Cobalt isotope. Color changes before and after γ-rays irradiation were observed, and the optical properties of the polymer films were investigated by spectrophotometry. Results show that increasing the radiation dose physically changed the color of the polymer film, from purple (pH > 8.8) without radiation (0 kGy) to yellow (almost transparent) (2.8 < pH < 7.2) at the highest dose (12 kGy). The concentration of acid formed due to irradiation increased with the increase in irradiation doses and at higher TCE content. The critical doses of PVA-TCE composites decreased linearly with the increase of TCE composition, facilitating an easy calibration process. The dose response at 438 nm increased exponentially with increasing radiation dose, but showed an opposite trend at the 575 nm band. An increase in the TCA concentration indicated a decrease in the absorption edge and an increase in activation energy, but both decreased for all TCE concentrations at higher doses. The energy gap for the direct and the indirect transitions decreased with increasing TCE concentration and γ-rays radiation dose. The results of this study demonstrated the potential application of PVA-TCE-CR polymer film as γ-rays irradiation dosimetry in a useful dose range of 0–12 kGy.
The increasing rate of oil and gas production has contributed to a release of oil/water emulsion or mixtures to the environment, becoming a pressing issue. At the same time, pollution of the toxic cigarette butt has also become a growing concern. This study explored utilization of cigarette butt waste as a source of cellulose acetate-based (CA) polymer to develop a phase inverted membrane for treatment of oil/water emulsion and compare it with commercial polyvinylidene difluoride (PVDF) and polysulfone (PSF). Results show that the CA-based membrane from waste cigarette butt offers an eco-friendly material without compromising the separation efficiency, with a pore size range suitable for oil/water emulsion filtration with the rejection of >94.0%. The CA membrane poses good structural property similar to the established PVDF and PSF membranes with equally asymmetric morphology. It also poses hydrophilicity properties with a contact angle of 74.5°, lower than both PVDF and PSF membranes. The pore size of CA demonstrates that the CA is within the microfiltration range with a mean flow pore size of 0.17 µm. The developed CA membrane shows a promising oil/water emulsion permeability of 180 L m−2 h−1 bar−1 after five filtration cycles. However, it still suffers a high degree of irreversible fouling (>90.0%), suggesting potential future improvements in terms of membrane fouling management. Overall, this study demonstrates a sustainable approach to addressing oil/water emulsion pollution treated CA membrane from cigarette butt waste.
25 October 2023 in Jurnal Penelitian Pendidikan IPA
The development of modern physics learning media based on project based learning integrated with smartphones to increase students' creativity and scientific literacy has been successfully carried out. The aim of this development is to produce modern physics learning media based on project based learning integrated with smartphones that is valid to increase students' creativity and scientific literacy. The media development uses a 4D model which consists of four stages, namely: define, design, develop and disseminate. Based on the results of assessments by material experts, learning media experts and learning experts, it can be concluded that modern physics learning media based on project based learning integrated with smartphones is very suitable to be used as a learning media in increasing students' creativity and scientific literacy.
31 January 2020 in Jurnal Penelitian Pendidikan IPA
The growth of tin oxide thin film by Aluminum doping and Fluorine has been carried out with the sol-gel spin coating technique. The growth aims to determine the quality of the thin layer formed based on variations in doping aluminum and fluorine. The basic ingredients used were SnCl2.2H2O, while the doping materials used were Al (Aluminium) and F (Fluorine) with variations in dopant concentrations (0, 5, 10, 15, 20 and 25)%. The growth of a thin layer using measured glass (10x10x 3) mm as a substrate. The growth of thin films includes substrate preparation, sol-gel making, thin film making, and heating processes. The growth of thin layer was dripped on a glass substrate with sol-gel spin coating technique at 1 M sol concentration and treated with maturation for 24 hours. The next step is making a thin layer using a spin coater at a speed of 2000 rpm for 3 minutes. After that, the substrate is heated in an oven at 100°C for 60 minutes. The results showed that the transparency level of the tin oxide layer increases with increasing amounts of doping Aluminum and fluorine. Key words: Aluminum, Fluorine, Sol-gel, Spin Coating, Thin Film, Tin Oxide
1 December 2009 in American Journal of Applied Sciences
Problem statement: The effects of gamma irradiation on optical properties of cresol-red dyed Poly Vinyl Alcohol (PVA) blended with Trichloroacetic Acid (TCA) for possible use in dosimetry and measurement of radiation dose in gamma rays have been studied using both Raman spectroscopy and UV-Visible spectrophotometer method. Approach: The dosimeters are composed of Poly Vinyl Alcohol (PVA), Trichloroacetic Acid (TCA) at various concentrations are 20, 25, 30 and 35%, and acid-base indicator cresol-red dyed. Results: The dosimeters were irradiated to doses up 12 kGy using 60Co gamma ray source at a constant dose rate. The polymeric films undergo color change from purple to yellow due to radiation-induced acid formation. The molecular vibrational spectra were measured using Raman spectroscopy, resulting in a decrease of the Raman intensity inelastic scattering of C-Cl molecular stretching from TCA with increasing dose. The absorption spectra were measured using UV-visible spectrophotometer in the wavelength range 350-700 nm, resulting in a decrease of the absorbance at 575 nm band peak with increasing dose. The dose sensitivity D0 increases with increasing TCA concentration for both scattering and absorption methods. The optical absorption studies show that the direct and indirect optical energy band gaps and optical activation energies are dependent on dose and TCA concentration. Conclusion: The shift in the optical band gap Eg values towards lower energy with radiation dose leads to a shift of the optical activation energy DeltaE value towards the lower energy region with increasing dose. The optical band gap (Eg) and the absorption edge decrease with increasing dose attributed to the structural disorder of polymer blends due to dehydrochlorination of trichloroacetic acid with increasing dose. The energy width of the tail of localized state in the forbidden band gap was evaluated using the Urbach-edges method. It was found that the activation energy (DeltaE) is less dependent of radiation dose but strongly dependent on concentration of blends.