Aris Doyan

Dr. Aris Doyan


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2021 in Polymers
Verified
Journal Article
Open access
PDF file
ADAris Doyan
Aris Doyan
SSSusilawati Susilawati
Susilawati Susilawati
Saiful PrayogiSaiful Prayogi
Saiful Prayogi
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
MAMuhamad Fatikul Arif
Muhamad Fatikul Arif
NINoor Maizura Ismail
Noor Maizura Ismail
This study investigated the polymer film composite of polyvinyl alcohol (PVA), trichlorethylene (TCE) and cresol red (CR) dye irradiated with gamma (γ) rays for potential application as radiation dosimetry. The film was prepared via the solvent-casting method with varying concentrations of TCE. Film samples were exposed to radiation from a γ-rays radiation source of 60Cobalt isotope. Color changes before and after γ-rays irradiation were observed, and the optical properties of the polymer films were investigated by spectrophotometry. Results show that increasing the radiation dose physically changed the color of the polymer film, from purple (pH > 8.8) without radiation (0 kGy) to yellow (almost transparent) (2.8 < pH < 7.2) at the highest dose (12 kGy). The concentration of acid formed due to irradiation increased with the increase in irradiation doses and at higher TCE content. The critical doses of PVA-TCE composites decreased linearly with the increase of TCE composition, facilitating an easy calibration process. The dose response at 438 nm increased exponentially with increasing radiation dose, but showed an opposite trend at the 575 nm band. An increase in the TCA concentration indicated a decrease in the absorption edge and an increase in activation energy, but both decreased for all TCE concentrations at higher doses. The energy gap for the direct and the indirect transitions decreased with increasing TCE concentration and γ-rays radiation dose. The results of this study demonstrated the potential application of PVA-TCE-CR polymer film as γ-rays irradiation dosimetry in a useful dose range of 0–12 kGy.

8 June 2021 in Polymers
Verified
Journal Article
Open access
PDF file
ADAris Doyan
Aris Doyan
LLLeong Chew Lee
Leong Chew Lee
Muhammad Roil BiladMuhammad Roil Bilad
Muhammad Roil Bilad
KKKiki Adi Kurnia
Kiki Adi Kurnia
SSSusilawati Susilawati
Susilawati Susilawati
KFKajornsak Faungnawakij
Kajornsak Faungnawakij
The increasing rate of oil and gas production has contributed to a release of oil/water emulsion or mixtures to the environment, becoming a pressing issue. At the same time, pollution of the toxic cigarette butt has also become a growing concern. This study explored utilization of cigarette butt waste as a source of cellulose acetate-based (CA) polymer to develop a phase inverted membrane for treatment of oil/water emulsion and compare it with commercial polyvinylidene difluoride (PVDF) and polysulfone (PSF). Results show that the CA-based membrane from waste cigarette butt offers an eco-friendly material without compromising the separation efficiency, with a pore size range suitable for oil/water emulsion filtration with the rejection of >94.0%. The CA membrane poses good structural property similar to the established PVDF and PSF membranes with equally asymmetric morphology. It also poses hydrophilicity properties with a contact angle of 74.5°, lower than both PVDF and PSF membranes. The pore size of CA demonstrates that the CA is within the microfiltration range with a mean flow pore size of 0.17 µm. The developed CA membrane shows a promising oil/water emulsion permeability of 180 L m−2 h−1 bar−1 after five filtration cycles. However, it still suffers a high degree of irreversible fouling (>90.0%), suggesting potential future improvements in terms of membrane fouling management. Overall, this study demonstrates a sustainable approach to addressing oil/water emulsion pollution treated CA membrane from cigarette butt waste.

1 February 2021 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
ADAris Doyan
Aris Doyan
SUSusilawati
Susilawati
LML Muliyadi
L Muliyadi
SHS Hakim
S Hakim
HMH Munandar
H Munandar
MTM Taufik
M Taufik
The synthesis of the SnO2 thin film with doped materials of aluminum, fluorin indium, a combination of aluminum and indium, a combination of aluminum and fluorine, an a combination of the three doping agents, namely aluminum, fluorine, and indium have be successfully carried out. The purpose of this synthesis is to determine the effect of the vario doping materials on the resulting bandgap energy value. The thin layer was synthesized usi the sol-gel spin coating technique with the ratio of the base material and doping material us were 95: 5% and 85: 15%. The results showed that the higher the doping materi concentration, the resulting bandgap energy value decreased. In addition, the highest bandg energy value is found in the SnO2 thin film with indium doping, namely for direct 3.62 eV (9 5% percentage) and 3.59 eV (percentage 85: 15%), while the indirect bandgap energy value 3, 92 eV (percentage 95: 5%) and 3.67 eV (percentage 85: 15%). The lowest energy band g value is found in the SnO2 thin film with a combination of the three doping aluminum, fluorin and indium, namely for direct 3.50 eV (95: 5% percentage) and 3.41 eV (percentage 85: 15% while the energy band gap value is indirect. namely 3.81 eV (percentage 95: 5%) and 3.55 e (percentage 85: 15%). All the energy band gap range in semiconductor materials.

31 January 2020 in Jurnal Penelitian Pendidikan IPA
Verified
Journal Article
Open access
PDF file
SSSusilawati Susilawati
Susilawati Susilawati
ADAris Doyan
Aris Doyan
LMLalu Muliyadi
Lalu Muliyadi
SHSyamsul Hakim
Syamsul Hakim
The growth of tin oxide thin film by Aluminum doping and Fluorine has been carried out with the sol-gel spin coating technique. The growth aims to determine the quality of the thin layer formed based on variations in doping aluminum and fluorine. The basic ingredients used were SnCl2.2H2O, while the doping materials used were Al (Aluminium) and F (Fluorine) with variations in dopant concentrations (0, 5, 10, 15, 20 and 25)%. The growth of a thin layer using measured glass (10x10x 3) mm as a substrate. The growth of thin films includes substrate preparation, sol-gel making, thin film making, and heating processes. The growth of thin layer was dripped on a glass substrate with sol-gel spin coating technique at 1 M sol concentration and treated with maturation for 24 hours. The next step is making a thin layer using a spin coater at a speed of 2000 rpm for 3 minutes. After that, the substrate is heated in an oven at 100°C for 60 minutes. The results showed that the transparency level of the tin oxide layer increases with increasing amounts of doping Aluminum and fluorine. Key words: Aluminum, Fluorine, Sol-gel, Spin Coating, Thin Film, Tin Oxide

20 June 2019 in Jurnal Penelitian Pendidikan IPA
Verified
Journal Article
Open access
PDF file
KKKartini Kartini
Kartini Kartini
ADAris Doyan
Aris Doyan
KKKosim Kosim
Kosim Kosim
SSSusilawati Susilawati
Susilawati Susilawati
BKBaiq Uswatul Khasanah
Baiq Uswatul Khasanah
LMLalu Muliyadi
Lalu Muliyadi
This study aims to produce a product in the form of a science learning model for the acquisition of motion material concepts in valid objects, with the development path using a 4D model consisting of 4 stages of development namely define, design, develop, and disseminate. Learning tools developed are syllabus, Lesson Plain, SAS and tests of critical thinking skills and student learning outcomes. However, at this writing focused on the process of validation testing through validation tests on the development of devices made. The final result of this study is to produce valid learning development products. Keywords: Learning Devices, Validation

26 January 2018 in Jurnal Penelitian Pendidikan IPA
Verified
Journal Article
Open access
PDF file
ADAris Doyan
Aris Doyan
MTMuhammad Taufik
Muhammad Taufik
RARaudah Anjani
Raudah Anjani
The purpose of this study is determine the effect of multi representation learning approaches to physics learning, the effect of students learning motivation on physics learning, and the interaction between the multi representational learning approach and the students learning motivation toward the learning outcomes of physics. This type of research is quasi experiment with non-equivalent group design. Sampling using purposive sampling technique, so that obtained class XI MIA 1 as experiment class and class XI MIA 2 as control class. The research instrument is a multiple choice test for physics learning result of 25 questions that have been tested for validity, reliability, level of difficulty, and different power of problems. The learning data of the two classes is normally distributed. Based on the homogeneity data obtained both homogeneous. Instrument to measure motivation to learn in the form of motivation questionnaire that has been tested by the expert team of validity. Data were analyzed by two-way ANOVA test. Result of data analysis show Ftable at 5% significance level equal to 3,97. Test the effect of multi representation learning approaches to physics learning equal to Fcount (8,857) > Ftable (3,97). Test the effect of students learning motivation on physics learning equal to Fcount (9.00) > Ftable (3,97). Test the interaction between the multi representational learning approach and the students learning motivation toward the learning outcomes of physics equal to Fcount (2.00) < Ftable (3,97). Based on these facts it can be concluded that there is influence of multi representation learning approach to physics learning result, there is influence of learning motivation learners to physics learning result, and there is no interaction between multi-representation learning approach with learning motivation of learners toward physics learning result.Keywords: multi representation learning approach, physics learning result, learning motivation