In the high-power laser system, the mid-spatial frequency error of the surface of the high-power laser component will affect the normal operation of the high-power laser system. In order to improve the mid-spatial frequency error of the high-power laser component after magnetorheological finishing, the causes and influencing factors of the ribbon fluctuation in magnetorheological finishing are studied, and the influence of different ribbon fluctuation on the mid-spatial frequency error of the surface is studied. Firstly, the influence of different ribbon fluctuations on the mid-spatial frequency error of the machined surface is simulated by a computer. Secondly, the magnetic field in the circumferential direction of the polishing wheel, the fluctuation amount and frequency of the magnetorheological polishing ribbon are measured, and then the causes of the fluctuation of the magnetorheological polishing ribbon are analyzed. Moreover, through the principle of a single variable, the influence of process parameters on the fluctuation of magnetorheological polishing ribbon is explored. Finally, the fused silica component is scanned uniformly under the process parameters of magnetorheological polishing ribbon fluctuation of 40 μm, 80 μm, 150 μm, and 200 μm. The experimental results show that the greater the ribbon fluctuation, the greater the surface mid-spatial frequency error of the component, and the ribbon fluctuation is approximately linear with the RMS of the PSD2 in the mid-spatial frequency band on the surface of the component. Therefore, the fluctuation of the ribbon can be controlled by controlling the magnetorheological processing parameters, and the mid-spatial frequency band error on the surface of the high-power laser component can be significantly reduced by optimizing process parameters after magnetorheological finishing.

A deterministic figuring method for cylindrical surface based on abrasive belt polishing is proposed in this study in order to improve the geometric accuracy of metal shaft parts. The principal motion of material removal is performed through the axial oscillation of the abrasive belt, and the different material removal at different positions can be obtained through servo control of the machine tool spindle by removing high error spots on the cylindrical surface and finally deterministically corrects the roundness error. An abrasive belt-based deterministic figuring device was built, and the figuring experiments were performed on the surface of steel workpieces 100 mm in diameter and 130 mm in effective length. The roundness errors of the entire workpiece after twice figuring iterations decreased nearly from the initial 3 μm to 1 μm, which preliminary verified the feasibility of this method. This deterministic figuring method is expected to break the machining accuracy limit and improve the rotation precision of the precision shaft parts such as the aerostatic spindle.

Abrasive water jet polishing has significant advantages in the manufacturing of complex optical components (such as high-slope optical component cavities) that require high-precision manufacturing. This is due to its processing process, in which the polishing tool does not make direct contact with the surface of the workpiece, and instead maintains a considerable distance. However, the removal functions of most existing abrasive water-jet polishing technologies do not possess strict symmetry, which significantly impacts the ability to correct surface figure errors. Therefore, this study implements rotating abrasive water-jet polishing based on traditional abrasive water jet processing to optimize the removal function, which turns it into a Gaussian form; thus, obtaining a type of removal function more suitable for CCOS polishing. This paper derives an empirical formula between the distance s’ from the peak removal point of the removal function to the stagnation point and the nozzle tilt angle α, based on geometric relationships and experimental results, analyzes the relationship between material removal efficiency, nozzle tilt angle, and standoff distance. Finally, this paper verifies through experiments the validity of this empirical formula under different process parameters. Therefore, this study obtains the process conditions that allow rotating abrasive water-jet polishing technology to achieve a stable Gaussian form removal function, and the appropriate process parameters to be selected in conjunction with polishing efficiency; thereby, effectively improving the removal function’s corrective ability and manufacturing efficiency. It provides theoretical support for the processing capability and process parameter selection of abrasive water-jet polishing technology, solves the problem of limited shaping capability of existing abrasive water jet tools, and significantly improves the manufacturing capability of high-end optical components.

High-precision optical component manufacturing by ion beam machining tools with ultra-high material removal resolution and dynamically adjustable removal efficiency is important in various industries. In this paper, we propose a low-energy pulsed ion beam (LPIB) technology that can obtain a single pulse with high-resolution material removal by adjusting the pulse frequency and duty cycle, and enable the dynamic adjustment of the removal efficiency. The pulse frequency is 1–100 Hz, and the duty cycle is 0–100%. For monocrystalline silicon, the pulse frequency and duty cycle are set to 100 Hz and 1%, respectively; thus, the single-shot pulse depth removal resolution of material is 6.7 × 10⁻⁴ nm, which means every 21 pulses can remove one silicon atom layer. Compared with IBF, where the removal resolution of the maximum depth is about 0.01 nm, the controllable resolution is one to two orders of magnitude higher. There is a linear relationship between the removal efficiency of the pulsed ion beam removal function and the pulse duty ratio. The material removal of a single pulse can be adjusted in real time by adjusting the pulse duty cycle and frequency. Owing to its high resolution and wide adjustable removal efficiency, LPIB has broad application prospects in the field of sub-nano-precision surface modification, quality tuning of inertial resonant devices, and so on. This technology is expected to advance surface processing and ultra-precision manufacturing.

The application of ultra-precision shaft parts is widely used, such as the spindle core of the air bearing spindle in ultra-precision machine tools. The precision of the spindle core is extremely high, and it is very difficult to obtain directly by traditional Computer Numerical Control (CNC) machine tools but is mostly obtained by manual grinding, whose machining efficiency is greatly limited. Based on the deterministic figuring theory, this paper focuses on the ultra-precision roundness, optimizing the filtering parameters of the measurement error data and studying the generation mechanism of the removal function morphology; the shape of the removal function is adjusted by combining the analysis of the figuring ability and positioning error. Finally, the optimized removal function is used on an experimental steel shaft, the average roundness convergence ratio is 72% higher than that of the original removal function, and the roundness reaches a 0.1 μm level. The result shows that a reasonable filtering of measured data and the removal function adjusted for the surface feature can improve the efficiency and precision of deterministic figuring on shaft parts.

Single-crystal silicon carbide has excellent electrical, mechanical, and chemical properties. However, due to its high hardness material properties, achieving high-precision manufacturing of single-crystal silicon carbide with an ultra-smooth surface is difficult. In this work, quantum dots were introduced as a sacrificial layer in polishing for pulsed-ion-beam sputtering of single-crystal SiC. The surface of single-crystal silicon carbide with a quantum-dot sacrificial layer was sputtered using a pulsed-ion beam and compared with the surface of single-crystal silicon carbide sputtered directly. The surface roughness evolution of single-crystal silicon carbide etched using a pulsed ion beam was studied, and the mechanism of sacrificial layer sputtering was analyzed theoretically. The results show that direct sputtering of single-crystal silicon carbide will deteriorate the surface quality. On the contrary, the surface roughness of single-crystal silicon carbide with a quantum-dot sacrificial layer added using pulsed-ion-beam sputtering was effectively suppressed, the surface shape accuracy of the Ø120 mm sample was converged to 7.63 nm RMS, and the roughness was reduced to 0.21 nm RMS. Therefore, the single-crystal silicon carbide with the quantum-dot sacrificial layer added via pulsed-ion-beam sputtering can effectively reduce the micro-morphology roughness phenomenon caused by ion-beam sputtering, and it is expected to realize the manufacture of a high-precision ultra-smooth surface of single-crystal silicon carbide.