A micro-pyramid structured thin film with a broad-band infrared antireflection property is designed and fabricated by using the single-point diamond turning (SPDT) technique and combined with nano-imprint lithography (NIL). A structure with dimensions of 10 μm pitch and 5 μm height is transferred from the copper mold to the silicon nitride optical film by using NIL and proportional inductively-coupled plasma (ICP) etching. Reflectance of the micro-optical surface is reduced below 1.0% over the infrared spectral range (800–2500 nm). A finite-difference-time-domain (FDTD) analysis indicates that this micro-structure can localize photons and enhance the absorption inside the micro-pyramid at long wavelengths. As described above, the micro-pyramid array has been integrated in an optical film successfully. Distinguishing from the traditional micro-optical components, considering the effect of refraction and diffraction, it is a valuable and flexible method to take account of the interference effect of optical film.

In this paper, synthetically using refraction, diffraction, and interference effects to achieve free manipulation of the focused optical field, we firstly present a photonic nanojet (PNJ) generated by a micropyramid, which is combined with multilayer thin films. The theory of total internal reflection (TIR) was creatively used to design the base angle of the micropyramid, and the size parameters and material properties of the microstructure were deduced via the expected optical field distribution. The as-designed bilayer micropyramid array was fabricated by using the single-point diamond turning (SPDT) technique, nanoimprint lithography (NIL), and proportional inductively coupled plasma (ICP) etching. After the investigation, the results of optical field measurement were highly consistent with those of the numerical simulation, and they were both within the theoretical calculation range. The bilayer micropyramid array PNJ enhanced the interference effect of incident and scattered fields; thus, the intensity of the focused light field reached 33.8-times that of the initial light, and the range of the focused light field was extended to 10.08$\lambda$. Moreover, the full width at half maximum (FWHM) of the focal spot achieved was 0.6$\lambda$, which was close to the diffraction limit.

Double perovskite Cs₂SnI₆ and its doping products (with SnI₂, SnF₂ or organic lithium salts added) have been utilized as p-type hole transport materials for perovskite and dye-sensitized solar cells in many pieces of research, where the mechanism for producing p-type Cs₂SnI₆ is rarely reported. In this paper, the mechanism of forming p-type Li⁺ doped Cs₂SnI₆ was revealed by first-principles simulation. The simulation results show that Li⁺ entered the Cs₂SnI₆ lattice by interstitial doping to form strong interaction between Li⁺ and I⁻, resulting in the splitting of the α spin-orbital of I–p at the top of the valence band, with the intermediate energy levels created and the absorption edge redshifted. The experimental results confirmed that Li⁺ doping neither changed the crystal phase of Cs₂SnI₆, nor introduced impurities. The Hall effect test results of Li⁺ doped Cs₂SnI₆ thin film samples showed that Li⁺ doping transformed Cs₂SnI₆ into a p-type semiconductor, and substantially promoted its carrier mobility (356.6 cm²/Vs), making it an ideal hole transport material.

Hafnium oxide thin films have attracted great attention as promising materials for applications in the field of optical thin films and microelectronic devices. In this paper, hafnium oxide thin films were prepared via DC magnetron sputtering deposition on a quartz substrate. The influence of various negative biases on the structure, morphology, and mechanical and optical properties of the obtained films were also evaluated. XRD results indicated that ($\overline{1}11$)-oriented thin films with a monoclinic phase could be obtained under the non-bias applied conditions. Increasing the negative bias could refine the grain size and inhibit the grain preferred orientation of the thin films. Moreover, the surface quality and mechanical and optical properties of the films could be improved significantly along with the increase in the negative bias and then deteriorated as the negative bias voltage arrived at −50 V. It is evident that the negative bias is an effective modulation means to modify the microstructural, mechanical, and optical properties of the films.

In this paper, comprehensively utilizing the diffraction theory and electromagnetic resonance effect is creatively employed to design a multifunctional metasurface zone plate (MMZP) and achieve the control of polarization states, while maintaining a broadband achromatic converging property in a near-IR region. The MMZP consists of several rings with fixed width and varying heights; each ring has a number of nanofins (usually called meta-atoms). The numerical simulation method is used to analyze the intensity distribution and polarization state of the emergent light, and the results show that the designed MMZP can realize the polarization manipulation while keeping the broadband in focus. For a specific design wavelength (0.7 μm), the incident light can be converted from left circularly polarized light to right circularly polarized light after passing through the MMZP, and the focusing efficiency reaches above 35%, which is more than twice as much as reported in the literature. Moreover, the achromatic broadband focusing property of the MMZP is independent with the polarization state of the incident light. This approach broadens degrees of freedom in micro-nano optical design, and is expected to find applications in multifunctional focusing devices and polarization imaging.

Some special conditions are important for chemical syntheses, such as high temperature and the medium used; unfortunately, uncontrollable influences are introduced during the process, resulting in unexpectedly low repeatability. Herein, we report a facile, environmentally friendly, stable, and repeatable methodology for synthesizing silver nanoplates (SNPs) at 0 °C that overcomes these issues and dramatically increases the yield. This method mainly employs sodium dodecyl sulfate (SDS) and sodium alginate (SA) as the surface stabilizer and assistant, respectively. Consequently, we produced hexagonal nanoplates and tailed nanoplates, and the characterization showed that SA dominates the clear and regular profiles of nanoplates at 0 °C. The tailed nanoplates, over time, showed the growth of heads and the dissolving of tails, and inclined to the nanoplates without tails. The synthesis method for SNPs used in this study—0 °C without media—showed high repeatability. We confirmed that these special conditions are not required for the synthesis of silver nanostructures (SNSs). Furthermore, we constructed a new method for preparing noble metal nanostructures and proved the possibility of preparing metal nanostructures at 0 °C.