The paper presents the results of the synthesis and study of CuAl layered double hydroxides (LDHs) as well as their application as catalysts for the selective hydrogenation of crotonaldehyde. Phase-homogeneous LDHs were obtained by co-precipitation and mechanochemical methods, and critical parameters ensuring the formation of the target product were identified. In the case of coprecipitation, the formation of LDH is most affected by the pH of the reaction medium and the CO32−/Al3+ ratio. The optimal CO32−/Al3+ ratio is ca. 0.5–0.8 and pH 9.5–10.0. When mechanochemical synthesis is used, at 500 m·s−2 and 60 min, it is possible to obtain a single-phase CuAl LDH, whereas at higher energies, LDH is destroyed. The mechanochemical method makes it possible not only to reduce the synthesis time and the amount of alkaline wash water but also to obtain more dispersed copper particles with a higher hydrogenating activity. The conversion of 2-butenal (T = 80 °C, P = 0.5 MPa, 180 min, ethanol) for this sample was 99.9%, in contrast to 50.5% for the catalyst obtained by co-precipitation. It is important that, regardless of the conversion, both catalysts showed high selectivity (S = 90–95%) for the double bond hydrogenation.
In the present work, complex powder alloys containing spinel as a minor phase were produced by mechanical alloying in a high-energy planetary ball mill from a 33Al–45Cu–22Fe (at.%) powder blend. These alloys show characteristics suitable for the synthesis of promising catalysts. The alloying was conducted in two stages: at the first stage, a Cu+Fe powder mixture was ball-milled for 90 min; at the second stage, Al was added, and the milling process was continued for another 24 min. The main products of mechanical alloying formed at each stage were studied using X-ray diffraction phase analysis, Mössbauer spectroscopy, transmission electron microscopy, and energy-dispersive spectroscopy. At the end of the first stage, crystalline iron was not found. The main product of the first stage was a metastable Cu(Fe) solid solution with a face-centered cubic structure. At the second stage, the Cu(Fe) solid solution transformed to Cu(Al), several Fe-containing amorphous phases, and a spinel phase. The products of the two-stage process were different from those of the single-stage mechanical alloying of the ternary elemental powder mixture; the formation of undesirable intermediate phases was avoided, which ensured excellent composition uniformity. A sequence of solid-state reactions occurring during mechanical alloying was proposed. Mesopores and a spinel phase were the features of the two-stage milled material (both are desirable for the target catalyst).
The structure, morphology, and chemical composition of the surface and near-surface layers of platinoid wires of polycrystalline gauzes, containing Pt (81 wt %), Pd (15 wt %), Rh (3.5 wt %), and Ru...
Catalysts based on CuAl-, CoAl-, and CuCoAl-layered hydroxides with M2+/Al = 2 and Cu/Co = 1 molar ratio were obtained. The effect of amount of cobalt on the structural properties, morphology, surface cations distribution, oxide phase formation, thermal stability of the samples and reduction of metals from them was studied. The effect of reaction conditions (temperature, time, pressure, solvent) and conditions of preliminary treatment of catalysts on their catalytic properties in furfural hydrogenation was established. High selectivity to furfuryl alcohol was observed for all the samples irrespective of pretreatment and reaction conditions. The synergetic effect in furfural hydrogenation between Co and Cu in the CuCoAlOx catalysts was revealed when ethanol is used as a solvent.
Platinum alloy gauzes are employed for the high-temperature oxidation of NH3 to NO used in the industrial production of HNO3 for application in agricultural fertilizers. To enhance the efficiency of NH3 oxidation, various Pt–Pd–Rh alloys are employed for the production of such catalytic gauzes. To understand the role of these metals in NH3 oxidation, scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction were applied to investigate the morphology, composition and structure of Pt, Pd and Rh foils after annealing in O2 and oxidation of NH3 with air at 1133 K. After annealing in O2 and NH3 oxidation, the metallic microgranular structure was detected on Pt(poly), whereas oxide layers of Rh2O3 and PdO were observed on Rh(poly) and Pd(poly). At the onset of NH3 oxidation (t = 1 h), fibrous metal-oxide agglomerates of nanofibers formed on these oxide layers. The long-term (5–10 h) oxidation of NH3 led to the formation of a continuous layer of pyramidal crystals on Rh(poly) and palladium “cauliflowers” on Pd(poly). The highly exothermic reaction of NH3 with oxygen on metals and PdO or Rh2O3 initiates strong catalytic etching forming grains and facets on Pt, fibrous metal-oxide agglomerates, pyramidal crystals and metallic “cauliflowers” on Rh and Pd.
High-temperature oxidation of NH3 on Pt alloy gauzes to NO is widely employed in industry for the production of HNO3, which is used to obtain agricultural fertilizers. Particular attention is paid now to the investigation of the chemical composition of gauzes used in NH3 oxidation. X-ray photoelectron and energy-dispersive X-ray spectroscopies with the depth of analysis ca. 5 nm and ca. 500 nm were applied to investigate the chemical composition of surface and subsurface layers of the new and used in NH3 oxidation with air at T = 1133 K Pt–Pd–Rh–Ru catalytic gauzes (81, 15, 3.5, 0.5 wt.%, respectively). For all the gauzes, adsorption (OHad, COad), graphitic (Cgr) and oxide (Rh2O3) films were found on the surface of the metallic alloy. Under these films, Cab, Nab and Oab atoms absorbed in the subsurface layers were detected on the gauzes used in NH3 oxidation. The obtained data testify to the penetration of Oab and Nab atoms into deeper layers of the alloy during etching with elevation of the catalyst temperature. Oab atoms were accumulated predominantly on dislocations, etch pits and grain boundaries, whereas Nab atoms intercalated mostly into interstitial sites of the alloy lattice.