Sang-Hee Woo

Dr. Sang-Hee Woo

Korea Institute of Machinery & Materials, Yusong, Korea
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
YJYoonah Jeong
Yoonah Jeong
SLSeokhwan Lee
Seokhwan Lee
SWSang-Hee Woo
Sang-Hee Woo
Physical friction between a tire and the road surface generates tire wear particles (TWPs), which are a source of microplastics and particulate matter. This study investigated the trends of chemical leaching from TWPs depending on the treadwear rating of the tire. A road simulator was used to produce TWPs from tires with various treadwear ratings. Liquid chromatography–tandem mass spectrometry was used to analyze the chemical leaching from TWPs, with a particular focus on benzothiazole and its derivative 2-hydroxy benzothiazole. However, chemical mapping via high-resolution tandem mass spectrometry detected another derivative: 2-mercaptobenzothiazole. The benzothiazole groups were observed to have different leaching tendencies, implying that using benzothiazole as a marker compound may lead to incorrect TWP quantitation. The results of this research also suggest that the ecotoxicological influence of TWPs can vary with the treadwear rating of a tire.

17 May 2022 in Environmental Research
Verified
Journal Article
Closed access
GKGiwon Kang
Giwon Kang
KCKyungil Cho
Kyungil Cho
JSJiyoon Shin
Jiyoon Shin
SLSoodong Lee
Soodong Lee
SLSeung-Bok Lee
Seung-Bok Lee
CKChanghyuk Kim
Changhyuk Kim

15 July 2022 in Atmosphere
Verified
Journal Article
Open access
PDF file
SWSang-Hee Woo
Sang-Hee Woo
GLGunhee Lee
Gunhee Lee
BHBangwoo Han
Bangwoo Han
SLSeokhwan Lee
Seokhwan Lee
In this study, two different dust collectors, one based on an inertial separator and the other based on an electrostatic precipitator (ESP), were developed in order to reduce brake wear particulate matter (PM) emissions. Additionally, the collection efficiencies for brake wear particles (BWPs) of the inertial separator and the ESP were evaluated according to brake pad type. In the case of the inertial separator, the BWP collection efficiencies for the low-metallic (LM) and non-asbestos organic (NAO) pads were similar, and the cut-off size at 50% collection efficiency (D50) was 2.2 µm. The ESP was designed without an additional electrostatic charging device because naturally induced electrostatic charging occurred due to the friction between the brake disc and pad. The BWP collection efficiency of the ESP was higher for NAO pad than for LM pad because the BWPs generated from the NAO pad contained a relatively low iron (Fe) component compared to that of the LM pad, thereby generating more frictional electricity. The maximum ESP collection efficiencies of the BWPs generated from the LM and NAO pads were determined to be 60% and 75%, respectively, and the remaining BWPs that were not collected were presumed to be particles that were not frictionally charged.

24 June 2021 in Energies
Verified
Journal Article
Open access
PDF file
SWSang-Hee Woo
Sang-Hee Woo
JNJung-hun Noh
Jung-hun Noh
HRHassan Raza
Hassan Raza
HKHongsuk Kim
Hongsuk Kim
Recently, ammonium carbamate (AC) has attracted attention as a substitute for urea, which is a commonly used reductant for NOx emitted from combustion engines. The AC exists as a solid at room temperature, and it is decomposed to NH3 and CO2 gases by heating. Therefore, adequate heat transfer is an essential issue in the design of AC pyrolysis reactor. In this study, a numerical model that describes the sublimation of AC was developed. For modeling, this study considered the three different calculation zones: solid-phase zone, gas-phase zone, and sublimation zone. Additionally, during the sublimation process, collapse of upper solid AC into the hollow space below by the effect of gravity is considered. As a result, it is presented that the modeling shows reasonable information about the AC sublimation in a reactor, such as temperatures in a reactor, pressure of reactor, and flow rate of sublimated gas. However, it is also found that accurate prediction of spatial temperature distribution is challenging because it is related to the accurate prediction of the internal shape of AC and its collapse in a reactor.

30 June 2020 in Journal of Korean Society for Atmospheric Environment
Verified
Journal Article
Closed access
SWSang-Hee Woo
Sang-Hee Woo
YKYongrae Kim
Yongrae Kim
SLSunyoup Lee
Sunyoup Lee
YCYoung Choi
Young Choi
SLSeokhwan Lee
Seokhwan Lee

1 October 2020 in Transaction of the Korean Society of Automotive Engineers
Verified
Journal Article
Open access
SWSang-Hee Woo
Sang-Hee Woo
YKYongrae Kim
Yongrae Kim
YCYoung Choi
Young Choi
SLSunyoup Lee
Sunyoup Lee
SLSeokhwan Lee
Seokhwan Lee