Chaorong Zheng

Dr. Chaorong Zheng

School of Civil Engineering, Harbin Institute of Technology, Harbin, Heilongjiang, China
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 October 2022 in Atmosphere
Verified
Journal Article
Open access
PDF file
ZWZhaoyong Wang
Zhaoyong Wang
Chaorong ZhengChaorong Zheng
Chaorong Zheng
JMJoshua Adriel Mulyanto
Joshua Adriel Mulyanto
Yue WuYue Wu
Yue Wu
Corner modifications can reduce wind loads acting on supertall buildings and modify the corresponding flow structures. The present study investigated the aerodynamic shape optimization of the corner recession square cylinders with multiple geometric parameters in a large design space via the GA-GRNN surrogate model updating-based multi-objective optimization framework. Six typical optimal aerodynamic shape sections M1~M6 were selected from the Pareto optimal front, and the effects of multiple geometric parameters of these sections on the aerodynamic performance and flow field were analyzed. The results showed that the present multi-objective optimization framework can significantly reduce the computational load and time cost, and significantly improve the optimization efficiency in solving complex engineering problems. The optimal corner recession sections can obviously reduce the mean drag coefficient CD and root mean square lift coefficient CσL while significantly increasing the Strouhal number St of the square cylinder, and it is concluded that the aerodynamic shape optimization can significantly improve the aerodynamic performance of square-sectional supertall buildings. When compared with the benchmark section, the CD and CσL of the optimal section M1 can be reduced up to 45.7% and 84.5%, respectively. Based on the analysis of the flow structures around the optimal sections, the flow mechanism can be attributed to the fact that the corner recession modifications postpone the flow separation, and deflect the separated shear layer towards the side surfaces and suppress the development of vortex shedding in the wake, which leads to significant elongation of the wake length and reduction of the width of the recirculation region. The proposed multi-objective optimization framework in this study can provide an important reference for the aerodynamic shape optimization of building structures and relevant studies.

1 July 2010 in Journal of Zhejiang University-SCIENCE A
Verified
Journal Article
Closed access
PDF file
Chaorong ZhengChaorong Zheng
Chaorong Zheng
YZYao-Chun Zhang
Yao-Chun Zhang
To reduce the wind-induced drag and improve the wind-resistance performance of a high-rise building, steady suction control is introduced into the building structure. Based on validation of the numerical methods by experiment with suction control over the flow separation of a 3D backward-facing step, the Reynolds stress equation model is used to investigate the drag reduction (DR) properties of a high-rise building whose side faces are controlled by all-height suction. Effects of the orifice geometrical parameters and suction flux parameters on the DR and the separation control are analyzed, and the detailed flow fields are shown to clarify the mechanism of suction control. The results indicate that suction control is very effective in reducing the wind loads on the high-rise building model, and only the dimensionless suction flux dominates. Lastly, the power consumed and the counterforce induced by suction are discussed, the suction models become the “zero-drag” model under certain suction angles.

15 January 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YZYuhao Zhu
Yuhao Zhu
YZYuhao Zhu
Yuhao Zhu
YCYong Chen
Yong Chen
CMChenyan Ma
Chenyan Ma
LWLingjun Wang
Lingjun Wang
Bowen YanBowen Yan
Bowen Yan
Wind tunnel test results can be influenced by various factors such as the blockage ratio and scaling ratio. These factors may introduce errors in the experimental outcomes, impacting the accuracy and reliability of the data obtained. This study quantitatively assesses consistency and identifies uncertainty sources to enhance result uniformity across various wind tunnel laboratories. This study conducted a systematic comparison between different wind tunnels in terms of rigid model pressure measurement wind tunnel experiments on the same Commonwealth Advisory Aeronautical Research Council (CAARC) standard tall building model. The study analyzes and discusses the results of mean and root-mean-square (RMS) wind pressure coefficients, peak factors, extreme wind pressure coefficients, probability density distributions, and base overturning force coefficients. The results indicated that in the open-circuit wind tunnel laboratory, the mean wind pressure coefficient is underestimated in the positive pressure region and overestimated in the negative pressure region. This is due to the static pressure which significantly decreases the streamwise direction within the test section, and the difference in static pressure is logarithmically proportional to the mean wind speed. Additionally, dynamic pressure is uniformly distributed along the test section axis. The inaccurate measurement of static pressure leads to these results. To address this issue, an indirect measurement method was employed to correct the static pressure results and reduce the error in the mean wind pressure coefficient to within 10%. Furthermore, differences in turbulence integral scale result in an error of up to 16% in the RMS wind pressure coefficient. Therefore, when conducting rigid model pressure measurement wind tunnel experiments, especially in open-circuit wind tunnel laboratories, careful consideration should be given to the influence of static pressure drop and integral length scale of turbulence.

1 September 2017 in Review of Scientific Instruments
Verified
Journal Article
Closed access
ZLZhao Liu
Zhao Liu
Chaorong ZhengChaorong Zheng
Chaorong Zheng
YWYue Wu
Yue Wu
Wind profilers have been widely adopted to observe the wind field information in the atmosphere for different purposes. But accuracy of its observation has limitations due to various noises or disturbances and hence need to be further improved. In this paper, the data measured under strong wind conditions, using a 1290-MHz boundary layer profiler (BLP), are quality controlled via a composite quality control (QC) procedure proposed by the authors. Then, through the comparison with the data measured by radiosonde flights (balloon observations), the critical thresholds in the composite QC procedure, including consensus average threshold T1 and vertical shear threshold T3, are systematically discussed. And the performance of the BLP operated under precipitation is also evaluated. It is found that to ensure the high accuracy and high data collectable rate, the optimal range of subsets is determined to be 4 m/s. Although the number of data rejected by the combined algorithm of vertical shear examination and small median test is quite limited, it is proved that the algorithm is quite useful to recognize the outlier with a large discrepancy. And the optimal wind shear threshold T3 can be recommended as 5 ms−1/100m . During patchy precipitation, the quality of data measured by the four oblique beams (using the DBS measuring technique) can still be ensured. After the BLP data are quality controlled by the composite QC procedure, the output can show good agreement with the balloon observation.

29 January 2024 in Atmosphere
Verified
Journal Article
Open access
PDF file
ZLZhao Liu
Zhao Liu
Chaorong ZhengChaorong Zheng
Chaorong Zheng
Dagang LuDagang Lu
Dagang Lu
YWYijing Wang
Yijing Wang
YCYong Chen
Yong Chen
ZZZhiming Zhang
Zhiming Zhang
A thousand-meter-high megatall building, which consists of three tear-drop-shaped towers arranged in an equilateral triangle and a central circular tower, has ten outdoor platforms along the height at an interval of 100 m to connect the four towers. As the pedestrian-level wind environment around the outdoor platforms of high-rise buildings has been less studied for higher incoming wind speeds than those of the ground wind, it is necessary to conduct the related research and evaluations of the pedestrian-level wind environment around outdoor platforms to ensure pedestrian comfort and safety. First, based on the flow field analysis of the megatall building model, potential aerodynamic measures are proposed to improve the pedestrian-level wind environment of outdoor platforms. Then, the wind tunnel test and CFD simulation of outdoor platforms are conducted with five aerodynamic measures, and an averaged adjustment coefficient is put forward to establish the link between the full model and the sub-configuration model for the wind speed amplification factor, Ri, greater than 1.0, so the data obtained from the wind tunnel test can be transformed for further assessment of the pedestrian-level wind environment. Finally, the Lawson criterion was used to quantitatively analyze and compare the effects of five aerodynamic measures to improve the wind environment, thus providing a design that satisfies the requirements of “wind comfort” and “wind safety” for the thousand-meter-high megatall pedestrian platform. This study contributes to the further understanding of pedestrian-level wind environment characteristics of outdoor platforms and the potential aerodynamic measures to improve wind comfort and wind danger.

13 July 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
KSKuo Sun
Kuo Sun
Chaorong ZhengChaorong Zheng
Chaorong Zheng
Yue WuYue Wu
Yue Wu
WZWenyuan Zhang
Wenyuan Zhang
Straw boards are the environmentally-friendly and sustainable materials used for building envelopes. To validate a novel alternative test method of thermal conductivity (λ), temperature control box–heat flux meter method (TCB-HFM), and better understand the thermal properties of straw boards, experimental investigation on two types of straw boards using such a method was carried out. Moreover, the control test via the conventional guarded hot plate method (GHP) was conducted to provide a benchmark. Results show that the fluctuation amplitudes of the temperature difference and heat flux density for the TCB-HFM during the steady state are much smaller than a generally acceptable limitation of 5%, and a 5.9% deviation of λ between the two test methods is in a reasonable range. It is indicated that the TCB-HFM can be regarded as an alternative test method to conduct investigations on the thermal properties of materials. Furthermore, the correlation between density and λ is explored and expressed by a linear fitting formula with the determination coefficient (R2) of 0.9193, and the formula is verified to have the feasibility to predict the λ of different types of straw bio-based materials.