Today, Discontinuously Reinforced Particulate Titanium Matrix Composites (DRPTMCs) have been the most popular and challenging in consideration with development and heat treatment due to their significant weight-saving capacity, high specific strength, stiffness and oxidising nature compared with other metals and alloys. Owing to their excellent capabilities, DRPTMCs are widely used in aerospace, automobiles, biomedical and other industries. However, regardless of the reinforcements, such as continuous fibres or discontinuous particulates, the unique properties of DRPTMCs have dealt with these composites for widespread research and progress around the domain. Even though DRPTMCs are one of the most studied materials, expedient information about their properties, processing, characterisation and heat treatment is still scattered in the literature. Hence, this paper focuses on a literature review that covers important research work that has led to advances in DRPTMCs material systems. Further, this paper also deals with broad details about the particulates, manufacturing processes and heat treatment processes.

In recent days the rising concern over environmental pollution with excessive use of synthetic materials has led to various eco-friendly innovations. Due to the organic nature, abundance and higher strength, natural fibers are gaining a lot of interest among researchers and are also extensively used by various industries to produce ecological products. Natural fibers are widely used in the composite industry as an alternative to synthetic fibers for numerous applications and new sources of fiber are continuously being explored. In this study, a fiber extracted from the Furcraea foetida (FF) plant is characterized for its feasibility as a reinforcement to fabricate polymer composite. The results show that the fiber has a density of 0.903 ± 0.07 g/cm³, tensile strength (σ_t) of 170.47 ± 24.71 MPa and the fiber is thermally stable up to 250 °C. The chemical functional groups and elements present in the FF fiber are evaluated by conducting Fourier transform infrared spectroscopy (FT-IR) and energy dispersive spectroscopy (EDS). The addition of FF fibers in epoxy reduced the density (13.44%) and hardness (10.9%) of the FF/Epoxy (FF/E) composite. However, the void content (V_c < 8%) and water absorption (WA: < 6%) rate increased in the composite. The FF/E composite with 30% volume of FF fibers showed maximum σ_t (32.14 ± 5.54 MPa) and flexural strength (σ_f: 80.23 ± 11.3 MPa).

In the last few decades, natural composite materials have been considered one of the highly sustainable ecological alternatives for reducing the consumption of synthetic materials. Today, research on natural fiber composites is the main thrust for their use in various industrial applications. Further, continuous research works are being carried out to utilize natural composites as an alternative to synthetic materials. However, the inhomogeneity of composites, delamination, fiber pullout, higher surface roughness (SR) and dimensional inaccuracy under traditional machining have led the attention towards non-traditional machining, such as abrasive water jet machining, to achieve high-quality components. Hence, in this study, an experimental analysis based on the design of experiments is conducted on the machinability of a hybrid rice straw/Furcraea foetida composite under abrasive water jet machining (AWJM). Further, the concentration of the rice straw and the AWJ process parameters are varied, and their effects on the quality of machining is evaluated. The experimental trials are designed based on the Taguchi L₂₇ orthogonal array, followed by an analysis of variance (ANOVA). From extensive experimentations, the concentration of rice straw is observed to be the most contributing (93.5%) factor to the SR. The traverse speed (TS) shows the highest percentage contributions of 93.13%, 55.50 and 55.70% to the material removal rate (MRR) and the top (T_KW) and bottom kerf widths (B_KW), respectively. However, the interaction between the fiber concentration and traverse speed gives the maximum contribution (35.04%) to the kerf taper (K_T). A second-order response surface model is generated to study the effects of the process parameters on the SR, MRR, T_KW, B_KW and K_T in any experimental domain. Finally, the microstructural characteristics of the machined surfaces, such as micro-cracks, debonding, and fiber pullout, are discussed.

Due to growing environmental concerns and economical and social problems in manufacturing sectors, there is a huge demand for the substitution of existing cutting fluids. Further, the cutting fluids selected are expected to reduce the cutting force, improve the surface roughness and also minimize the tool wear during machining operations. Hence, this paper discusses the tribological and morphological behaviour of AISI 316L stainless steel while turning under minimum quantity lubrication (MQL) such as oil–water emulsion, mineral oil, simarouba oil, pongam oil and neem oil based on Taguchi L₂₅ orthogonal array. From the extensive experimentation, it was observed that neem oil MQL with cutting speed of (140, 140, 60 m/min), feed of (0.30, 0.20, 0.10 mm/rev) and depth of cut of (1.0, 1.0, 1.0 mm) resulted in the lowest surface roughness (0.36 µm),cutting force (235.34 N) and tool wear (100.32 microns), respectively. Further, main effects plots and analysis of variance (ANOVA)can be successfully used to identify the optimum process input parameters and their percentage of contribution (P%) on the output parameters during turning of AISI 316L steel under MQL applications. The results clearly indicate that from both an ecological and economical standpoint, neem oil is the most effective lubricant in reducing cutting forces, tool wear and surface roughness during turning of AISI 316L stainless steel under MQL.

Today, among emerging materials, metal matrix composites, due to their excellent properties, have an increasing demand in the field of aerospace and automotive industries. However, the difficulties associated with the processing of these composites have been a challenge to manufacturing industries due to inhomogeneous mixing of the matrix with the reinforcement, oxidation, and microstructural phase transformation during processing. Hence, in this paper, Ti-6Al-4V reinforced with SiCp has been processed through a specially developed compression molding, followed by vacuum sintering. The main objective of this paper was to determine the favorable vacuum sintering conditions for Ti-6Al-4V reinforced with 15 Wt. % SiCp composites under a different aging temperature (°C), aging time (h), heating rate (°C/min), and cooling rate (°C /min) to improve the process output parameters such as the hardness, surface roughness, and to reduce the porosity using Taguchi’s Design of Experiments. Finally, the response surface methodology and random forest regression have been used to predict the optimum process output parameters. From the extensive experimentation and understanding gained from Taguchi’s Design of Experiments, the response surface methodology and random tree regression approach can be successfully used to predict the hardness, porosity, and surface roughness during the processing of Ti-6Al-4V-SiC_p composites.