A hybrid girder bridge adopts a steel segment at the mid-span of the main span of a continuous concrete girder bridge. The critical point of the hybrid solution is the transition zone, connecting the steel and concrete segments of the beam. Although many girder tests revealing the structural behavior of hybrid girders have been conducted by previous studies, few specimens took the full section of a steel–concrete joint due to the large size of prototype hybrid bridges. In this study, a static load test on a composite segment to bridge the joint between the concrete and steel parts of a hybrid bridge with full section was conducted. A finite element model replicating the tested specimen results was established through Abaqus, while parametric studies were also conducted. The test and numerical results revealed that the concrete filling in the composite solution prevented the steel flange from extensive buckling, which significantly improved the load-carrying capacity of the steel–concrete joint. Meanwhile, strengthening the interaction between the steel and concrete helps to prevent the interlayer slip and simultaneously contributes to a higher flexural stiffness. These results are an important basis for establishing a rational design scheme for the steel–concrete joint of hybrid girder bridges.
2 January 2022 in Structural Engineering International
Mingzhuwan Bridge is currently the largest span three-main-truss steel arch bridge, with a main span of 436 m. It was opened to traffic on 28 June 2021. The upper structure adopts a three-main-truss arch-beam combination system, the main arch is an N-type truss of variable height and the main girder is an N-type truss of constant height. The main girder truss is arranged with double decks, and the suspenders are made of high-strength parallel wire cables. The deck system adopts an orthotropic steel deck. This technical report mainly introduces the technical characteristics of the three-main-truss space truss structure, rigid arch and rigid beam structure, and synchronous construction of arch and beam.
Hybrid girder bridges achieve significant improvements in spanning capacity by utilizing lightweight and high-strength materials in the midspan beam segments. To quantitatively describe the enhancement in spanning capacity, this study introduces a simplified analytical model for hybrid girder components, avoiding complex factors, such as span ratio and boundary conditions, typically encountered in previous system-level analyses. The Leq method is proposed based on this new model, utilizing classical beam theory model to calculate and compare hybrid girder components with both uniform and variable cross-sections. The equivalent span increase coefficient, , is introduced for the first time, and a simplified formula for its calculation is derived. The calculation errors are kept within 8%, which meets the requirements for preliminary design. Validated through engineering practice, the formula is concise and reveals that is solely related to the hybrid ratio, , and the linear load ratio, . This method provides valuable guidance for the conceptual design and ultimate span prediction of hybrid girder bridges.
This study experimentally and numerically investigated the overall buckling behavior of steel box column components. Two box section specimens were fabricated for axial compression tests. Prior to the tests, the material properties, initial geometric imperfections and residual stress were measured. In addition, an extended parameter analysis was conducted using a finite element model validated by experimental results to evaluate the impact of geometric defects and residual stresses on the bearing capacity of unstiffened and stiffened box section columns. A novel column curve was proposed based on massive datasets of parametric models. The short and long column specimens exhibited typical strength failure and buckling failure modes, respectively. The initial geometric imperfections and residual stresses slightly reduced the buckling strength from the models, with a maximum reduction in buckling strength owing to initial geometric imperfections of 5.2% and that owing to residual stresses of 6.52%. The unstiffened and stiffened box columns have the same stability coefficient when the slenderness ratio is the same. Additionally, the ultimate load capacity calculation formula for stiffened box columns proposed in this paper averages 2.20% higher than Class C curves in JTG D64-2015, lies between Japanese and U.S. codes, and demonstrates good accuracy.
Hybrid girder bridges can be likened to plant grafting, where mechanical traits are inherited from both rootstock and scion girders, enabling performance that exceeds that of the individual components. To quantitatively evaluate this inheritance and optimize hybrid girder performance, this study develops a bionic binary grafting model inspired by the genetic principles of quantitative trait inheritance. By analyzing the flexural behavior of hybrid girders through classical beam theory, the research explores two sequential phases: trait inheritance and trait optimization. In the inheritance phase, the bending moment is governed by the hybrid ratio and the positional advantage of scion girders. In the optimization phase, iterative refinements in girder height and internal force further enhance structural performance. The key contributions of this study are as follows: (1) a novel bionic framework is proposed to quantitatively characterize mechanical trait inheritance in hybrid girders, introducing inheritance ratios to describe the distribution of bending moment between rootstock and scion girders as functions of the hybrid ratio, stiffness ratio, and load ratio; (2) a design-oriented framework for mechanical trait optimization is developed, demonstrating that hybrid girders can achieve equivalent stress performance with reduced structural height; and (3) the proposed inheritance and optimization formulations are validated against representative engineering cases, confirming their accuracy in estimating the optimal inheritance ratio and girder height for hybrid girder bridges. This bio-inspired framework enhances our understanding of hybrid girder performance enhancement mechanisms, enabling the efficient optimization of structural systems during conceptual design by leveraging materials with diverse mechanical properties.