In subsurface irrigation systems in desert areas, the wetting front transport pattern allows the determination of irrigation flow and timing. In this study, an indoor subsurface irrigation experiment on aeolian sandy soil is designed, and the vertical and horizontal wetting front movement distances under different irrigation flows are obtained. The dimensional analysis method was used to perform a dimensional analysis on the experimental data. An empirical setting front distance estimation model, which only considers three parameters, saturated hydraulic conductivity Ks, irrigation flow Q, and total irrigation volume V, was proposed. The model’s accuracy was statistically evaluated with the observed data and verified by a numerical simulation using HYDRUS-2D/3D. The mean absolute error (MAE) and root mean square error (RMSE) of the proposed model in the horizontal and downward directions were 0.80 and 0.95 cm, respectively, with a percentage bias (PBIAS) of −3.47 ≤ ±10 and a Nash–Sutcliffe efficiency (NSE) of 0.98, which is close to 1. Thus, this model can contribute to the selection of the appropriate depth and spacing of subsurface laterals.
The utilization of steel slag (SS), fly ash (FA), and ground granulated blast furnace slag (GGBFS) as soil additives in construction represents a critical approach to achieving resource recycling of these industrial by-products. This study aims to activate the SS-FA-GGBFS composite with a NaOH solution and Na2CO3 and employ the activated solid waste blend as an admixture for lateritic clay modification. By varying the concentration of the NaOH solution and the dosage of Na2CO3 relative to the SS-FA-GGBFS composite, the effects of these parameters on the activation efficiency of the composite as a lateritic clay additive were investigated. Results indicate that the NaOH solution activates the SS-FA-GGBFS composite more effectively than Na2CO3. The NaOH solution significantly promotes the depolymerization of aluminosilicates in the solid waste materials and the generation of Calcium-Silicate-Hydrate and Calcium-Aluminate-Hydrate gels. In contrast, Na2CO3 relies on its carbonate ions to react with calcium ions in the materials, forming calcium carbonate precipitates. As a rigid cementing phase, calcium carbonate exhibits a weaker cementing effect on soil compared to Calcium-Silicate-Hydrate and Calcium-Aluminate-Hydrate gels. However, excessive NaOH leads to inefficient dissolution of the solid waste and induces a transformation of hydration products in the modified lateritic clay from Calcium-Silicate-Hydrate and Calcium-Aluminate-Hydrate to Sodium-Silicate-Hydrate and Sodium-Aluminate-Hydrate, which negatively impacts the strength and microstructural compactness of the alkali-activated solid waste composite-modified lateritic clay.
Porous artificial reef materials made of cement used in the offshore area can repair and improve the ecological environment and enrich fishery resources. In this study, quartz sand was used as the aggregate, high-alumina cement as the cementing agent, and crushed particles of waste tires as the modifier to prepare porous cement–polymer composites. Through orthogonal tests, the effects of the aggregate particle size, the ratio of aggregate to cement, the rubber particle size, and the rubber ratio on the strength and permeability of the porous cement–polymer composites were studied. The significant degrees of different influencing factors were analyzed, and an appropriate configuration scheme for the porous cement–polymer composites was proposed. The experimental results show that the quantity of rubber particles added and the particle size of the rubber particles have a relatively large impact on the properties of the porous cement–polymer composites. Through response surface tests, the interactive effects of various factors in the porous cement–polymer composites on the compressive strength and permeability of the material were verified. The microstructure of the porous cement–polymer composites was observed by SEM. The differences in the microstructure and internal structure between the specimens with a low rubber content and large rubber particle size and those with a high rubber content and small rubber particle size were analyzed, and the influence mechanism of the differences in the microstructure and internal structure on the strength and permeability was proposed.
Solid waste-based binder-stabilized laterite is prone to progressive deterioration under multiple coupled environmental factors in practical engineering applications. Conventional compression and direct shear tests fail to accurately characterize the gradient deterioration pattern of stabilized laterite specimens. In this study, a multi-factor test scheme was designed using response surface methodology, with wet–dry cycle number, initial humic acid content, and magnesium sulfate solution concentration selected as environmental factors. Continuous drilling resistance–drilling depth curves of stabilized laterite specimens were obtained using a drilling resistance measurement system, thereby quantitatively determining the deterioration depth and indirectly characterizing structural integrity via the drilling resistance in the stable drilling stage. Scanning electron microscopy observations were used to reveal the microscopic deterioration mechanism of stabilized laterite under the effects of environmental factors. The results of the regression show that the micro-drilling resistance in the stable drilling stage of undeteriorated stabilized laterite has a significant linear correlation with shear strength, indicating that micro-drilling resistance, as an indirect index of specimen integrity, also has potential for application in evaluating the strength of stabilized laterite. All three environmental factors increase the deterioration depth of stabilized laterite; wet–dry cycles exert the most significant effect and exhibit a statistically significant interaction within the investigated experimental domain with humic acid content, followed by magnesium sulfate concentration. For stabilized laterite subjected to wet–dry cycles and sulfate attacks, there exists a change point depth on the drilling resistance curve. Below this depth, the average micro-drilling resistance of the interior soil is mainly governed by the initial humic acid content. Microscopically, humic acid particles form weakly cemented zones in surrounding areas, which gradually evolve into preferential flow paths under wet–dry cycles, accelerating water infiltration and expanding deterioration depth. Magnesium sulfate crystallizes within pores to generate ettringite and other products, inducing extrusion stress on the cemented structure and further aggravating soil loosening and microcrack propagation.
Aeolian sand is widely distributed in arid and semi-arid regions, but its loose structure and low cohesion limit its direct engineering use. This study investigates the stabilization of aeolian sand using alkali-activated steel slag—fly ash system. Single-factor tests and an L25 (5 4 ) orthogonal design were conducted to evaluate the effects of steel slag content, fly ash content, NaOH dosage, and moisture content on shear strength and unconfined compressive strength. SEM, XRD, and FTIR analyses were further used to clarify the solidification mechanism. The results show that steel slag content is the dominant factor controlling shear strength and strength parameters, followed by NaOH dosage and fly ash content, while moisture content has the weakest influence. The optimal mixture was 12% steel slag, 10% fly ash, 4% NaOH, and 12% moisture. Under this condition, cohesion and internal friction angle reached 198.2 kPa and 51.1°, respectively, and UCS reached 2450 kPa at 7 d and 4860 kPa at 28 d. The strength improvement was mainly attributed to the formation of alkali-activated gels, pore filling, and enhanced interparticle bonding.
Permeable concrete bricks incorporating waste tire rubber particles were prepared to improve sustainability and optimize the balance between mechanical performance and hydraulic behavior. Orthogonal experiments and response surface methodology were used to investigate the effects of aggregate-to-binder ratio (A/B), water-to-binder ratio (W/B), rubber content, and rubber particle size on compressive strength and permeability coefficient. Results showed that rubber content dominated compressive strength, while A/B ratio had the greatest influence on permeability. Compressive strength decreased continuously with increasing rubber content and A/B ratio, whereas permeability increased with A/B ratio and showed non-monotonic responses to rubber content and particle size. Response surface optimization identified an optimum mixture: A/B = 3.006, W/B = 0.45, rubber content = 0.103, and rubber particle size = 0.525 mm, yielding a compressive strength of 18.97 MPa and a permeability coefficient of 1.82 mm/s. Validation tests showed relative errors of 1.32% for compressive strength and 3.85% for the permeability coefficient, respectively. SEM and CT analyses revealed that the performance of the permeable concrete bricks was governed by the balance among skeleton integrity, interfacial bonding, and pore connectivity. These findings support the valorization of waste tire rubber in sustainable permeable paving materials.