Heat energy storage is one of the most common technical solutions in the conditions of operation of low-potential and renewable energy sources. Adsorption heat energy storage devices based on the composite media “silica gel – salt” are the most effective in these conditions. The technique and technology of sol-gel synthesis of the composite adsorption materials “silica gel – sodium sulfate” and “silica gel – sodium acetate” have been developed. A special feature of this technique is a two-stage process involving the formation of silicon phase nuclei in the interaction of aqueous solutions of silicate glass and sulphuric or acetic acids in the presence of a polymeric quaternary ammonium salt and subsequent coarsening of the particles with the gradual addition of solutions of silicate glass and the corresponding acids. The essence of the technology consists in successive stages of formation and integration of the silicic phase nuclei, hydrolysis of functional OH- groups, filtration and drying of the fine precipitate. A qualitative difference in the adsorption properties of the synthesized composites and the mechanical mixture of salt – silica gel with sorption capacity inferior to them on average by 30% is revealed by differential thermal analysis. The processes of application of the composite adsorption materials “silica gel – sodium sulfate” and “silica gel – sodium acetate” obtained by the sol-gel method have been studied. A qualitative difference in the kinetics of adsorption of water by the composite adsorbents is shown as compared to massive salts. It is established that the amount of heat of adsorption of water vapor by the composite adsorbents of the materials “silica gel – sodium sulfate” and “silica gel – sodium acetate” is approximately 30 % greater than the linear superposition of salt and silica gel.
Authors introduce an ultrahigh-temperature (i.e., 2500–3000 °C) continuous fluidized bed furnace, in which the key operating variable is specific electrical resistance of the bed. A correlation has been established to predict the specific electrical resistance for the natural graphite-based precursors. Fluid dynamics models have been validated with the data from a fully functional prototype reactor. Data collected demonstrated that the difference between the calculated and measured values of specific resistance is approximately 25%; due to chaotic nature of electrothermal fluidized bed processes, this discrepancy was deemed acceptable. Optimizations proposed allow producing natural graphite-based end product with the purity level of 99.98 + wt. %C for battery markets.
The performance of an adsorptive heat-moisture regenerator based on a silica gel–sodium sulphate composite adsorbent was studied. The correlation between the adsorbent composition and structural characteristics of the laboratory-scale device was investigated. An algorithm for the calculation of the efficiency factors of the adsorptive regenerator was further developed. The suggested algorithm calculates the operational parameters, including the temperatures, humidities and volumetric flows of internal and external air, and estimates the regenerator’s performance via temperature and moisture efficiency factors, total adsorption and time needed to achieve maximum adsorption, air pressure loss and fan power input. The validity of the calculation results obtained using the proposed algorithm was confirmed experimentally. Temperature efficiency factor, air pressure loss and fan power consumption are crucial parameters for the estimation of the optimal operating regime of an adsorptive heat-moisture regenerator. The correlation between meteorological conditions and efficiency factors was assessed and applied in a simulation of residential house-scale air conditioning unit operation. Maximal values of temperature efficiency factor were found at internal and external air temperatures of 15 to 20 °C and −5 to 0 °C, respectively. Moisture efficiency factors were observed to reach their maximum at the absolute humidities of external and internal air of 4.0 to 5.0 g/m3 and 2.75 to 3.0 g/m3, respectively. The fan power consumption of the adsorptive heat-moisture regenerator was found to be comparable to or even lower than that of commercial air conditioning units used in comparably voluminous interiors.
1 January 2022 in Fundamental and applied problems of ferrous metallurgy
UTUkrainian State University of Science and Technologies
Ukrainian State University of Science and Technologies
+3
One of the main global trends in the development of the world economy is its decarbonization with the fulfillment of obligations to reduce greenhouse gas emissions. The processes of obtaining high-purity graphitized materials and ferrous metallurgy have significant consumption of energy carriers and, accordingly, emissions of greenhouse gases. Therefore, the development and implementation of innovative energy-saving technologies based on the electrothermal fluidized bed will allow to solve the emission of greenhouse gases during the production of electrode products. The purpose of the work is to determine the environmental efficiency of the implementation of innovative technology based on electrothermal fluidized bed in comparison with existing ones. The basis of the research methodology is the calculation of greenhouse gas emissions using specific emission rates during the production of electrical energy and burning of natural gas. The work proposes a methodology that takes into account the structure of electricity and fuel production in Ukraine, their types and quality. Technological costs of electricity during its transportation from stations to the consumer, specific fuel costs for electricity production are covered. Calculations were made for four variants of the technological process, which are implemented at PrJSC "Ukrgrafit" and include the stage of anthracite calcination in rotary furnaces or electrocalciners, the stage of graphitization in Achenson and Kastner furnaces. Two options of technologies with an electrothermal fluidized bed are analyzed in the work. The results of the calculations show that the proposed technology for obtaining finely dispersed artificial graphite based on anthracite from the Donetsk deposit significantly reduces greenhouse gas emissions by 2-3.5 times compared to the existing technologies of PrJSC "Ukrgrafit". Specific emissions of greenhouse gases decrease from 2500-2600 kg of CO2/t to 390-780 kg of CO2/t.
An innovative technology for processing selected recycled battery wastes from large format automotive lithium-ion batteries has been developed. One of the key steps of refining process is application of thermal treatment of granular matter in a new and improved modified electrothermal fluidized bed reactor at high temperature. The reactor design is based on fluidization and increase in electric resistance leading to higher temperatiures.