Room temperature (RT) synthesis of the ternary cesium lead bromide CsPbBr3 quantum dots with oleic acid and oleylamine ligands was developed by Zeng and coworkers in 2016. In their works, the supersaturated recrystallization (SR) was adopted as a processing method without requiring inert gas and high-temperature injection. However, the oleic acid ligand for haloplumbate is known to be relatively unstable. Hence, in this work, we employed the eco-friendly olive oil to replace the oleic acid portion for the SR process at RT. Resultantly, we found that the cube-shaped nanocrystal has a size of ~40–42 nm and an optical bandgap of ~2.3 eV independent of the surface ligands, but the photoluminescence lifetime (τav) and crystal packing are dependent on the ligand species, e.g., τav = 3.228 ns (olive oil and oleylamine; here less ordered) vs. 1.167 ns (oleic acid and oleylamine). Importantly, we explain the SR mechanism from the viewpoint of the classical LaMer model combined with the solvent engineering technique in details.
Recently, tuning the green emission of CsPbBr3 quantum dots (QDs) to blue through quantum size and confinement effects has received considerable attention due to its remarkable photophysical properties. However, the synthesis of such a blue-emitting QD has been challenging. Herein, supersaturated recrystallization was successfully implemented at room temperature to synthesize a broadband blue-emitting ZnBr2-doped CsPbBr3 QD with an average size of ~3 nm covering the blue spectrum. The structural and optical properties of CsPbBr3 QDs demonstrated that QD particle size may decrease by accommodating ZnBr2 dopants into the perovskite precursor solution. Energy-dispersive spectroscopy confirmed the presence of zinc ions with the QDs. This work provides a new strategy for synthesizing strongly quantum-confined QD materials for photonic devices such as light-emitting diodes and lighting.
6 January 2023 in Advances in Materials Science and Engineering
In this study, the role of active layer thickness, hole transport layer thickness, and electron mobility on the performance of P3HT: PCBM-based inverted organic solar cells has been investigated. The simulation has been done for device structure ITO/ZnO/P3HT: PCBM/MoO3/Ag using the general-purpose photovoltaic device model (GPVDM) program tool. The short circuit current density (Jsc), open circuit voltage (Voc), fill factor (FF), and power conversion efficiency (PCE) of the cell were determined by varying the thickness of the active layer from 140nm to 260nm, the hole transparent layer from 10nm to 40nm, and electron mobility from 0.5×10−3cm2V−1s−1 to 6.5×10−3cm2V−1s−1. The PCE improvement was observed at 220nm and 20nm active layer and hole transporting layer thickness, respectively, for 4.5×10−3cm2V−1s−1 electron mobility. The results confirmed that the thickness of the active layer, hole transport layer, and charge carrier mobility plays an important role in the performance improvement of organic solar cells.
13 April 2023 in Advances in Materials Science and Engineering
Because of its fundamental characteristics, including bioactivity, biodegradability, and nontoxicity, bioactive glasses (BGs) become among the most impressive materials in the area of biomedical applications. It is primarily utilized in the applications of dermal fillers, orthopedic implants, and pharmaceutical delivery systems. Here in this study, simple and continuous methods were employed to produce hollow spherical bioactive glasses (HSBGs) microspheres. Using a spray pyrolysis method, solid and hollow spherical particles were successfully synthesized, and the particle formation mechanism was also discussed in detail. Surface and inner morphologies of synthesized bioactive glass (BG) powders were investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. BET was employed to measure the pore volume as well as specific surface area for pure BG and BG-derived-PEG powders; all values are below 0.05, demonstrating noticeable distinction among both forms of synthesized powders. Using energy dispersive spectroscopy (EDS), the constituent components of prepared samples were assessed. In addition, by immersing samples in simulated bodily fluid (SBF) for 12 hr, in vitro bioactivity was tested by SEM. The viability of cells for both BG specimens was evaluated at various extraction concentrations by MTT assay (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenylte-trazolium bromide) for 72 hr. Relying on the Ca/P ratio obtained from SEM-EDS, HSBGs possessed higher hydroxyapatite-forming capacity than solid bioactive glasses (SBGs). In addition, the cell viability of both specimens showed that at all extraction concentrations, they pass the standard biocompatibility levels. Therefore, the HSBGs have better biocompatibility and in vitro bioactivity; hence they are promising for future tissue-engineering development.
27 February 2022 in Advances in Materials Science and Engineering
This article reports polymer solar cell performance evaluated using general-purpose photovoltaic device model (GPVDM) software for various device structures. The essential parameters of the cell such as short circuit current density (JSC), open-circuit voltage (VOC), fill factor (FF), and power conversion efficiency (PCE) are evaluated for these structures. The simulation result shows the performance of the cells could be highly affected by both interfacial and active layers. Among the demonstrated device structures, better performance is observed for device structure ITO/V2O5/PTB7:PC70BM/TiOx/Al with 10.4mA/cm2 short circuit current density, 0.89V open-circuit voltage, 59.5 fill factor, and 6.1 power conversion efficiency. The study is useful for a better understanding of the powerful effect of the materials in the device structure on the performance of the cell and thereby determines the proper device structure and materials for improving the performance of the cell.
The phase change of all-inorganic cesium lead halide (CsPbI3) thin film from yellow δ-phase to black γ-/α-phase has been a topic of interest in the perovskite optoelectronics field. Here, the main focus is how to secure a black perovskite phase by avoiding a yellow one. In this work, we fabricated a self-doped CsPbI3 thin film by incorporating an excess cesium iodide (CsI) into the perovskite precursor solution. Then, we studied the effect of organic additive such as 1,8-diiodooctane (DIO), 1-chloronaphthalene (CN), and 1,8-octanedithiol (ODT) on the optical, structural, and morphological properties. Specifically, for elucidating the binary additive–solvent solution thermodynamics, we employed the Flory–Huggins theory based on the oligomer level of additives’ molar mass. Resultantly, we found that the miscibility of additive–solvent displaying an upper critical solution temperature (UCST) behavior is in the sequence CN:DMF > ODT:DMF > DIO:DMF, the trends of which could be similarly applied to DMSO. Finally, the self-doping strategy with additive engineering should help fabricate a black γ-phase perovskite although the mixed phases of δ-CsPbI3, γ-CsPbI3, and Cs4PbI6 were observed under ambient conditions. However, the results may provide insight for the stability of metastable γ-phase CsPbI3 at room temperature.