Xionglei Lin

Dr. Xionglei Lin

orcid

Research Focus & Metrics

Representative Publications

View All Publications
10 December 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
Liang YuLiang Yu
Liang Yu
XFXingyang Feng
Xingyang Feng
Pengcheng HuPengcheng Hu
Pengcheng Hu
XLXionglei Lin
Xionglei Lin
TJTao Jing
Tao Jing
The development of high-precision satellites has increased the demand for ultraprecision three-degrees-of-freedom (3-DOF) angle measurements for detecting structural deformation. The required instrument should simultaneously measure pitch, yaw, and roll angles using a single reference point. This paper proposes a 3-DOF angle measurement method based on the wavefront interference principle, and a mathematical model and its decoupling algorithm were built. Then, an angle-sensing probe with an extremely simple structure was designed and constructed. Finally, a series of experiments were performed to verify the method’s feasibility. The experiment results showed that the roll, pitch, and yaw measurement resolution of the probe was better than 10, 1, and 1 μrad, respectively, providing a high-performance 3-DOF angle measurement with a single probe. The short-term stabilities of roll, pitch, and yaw were better than 22, 1.7, and 2.0 μrad, respectively.

30 October 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
Haijin FuHaijin Fu
Haijin Fu
ZWZheng Wang
Zheng Wang
XLXionglei Lin
Xionglei Lin
XXXu Xing
Xu Xing
Ruitao YangRuitao Yang
Ruitao Yang
Liang YuLiang Yu
Liang Yu
This paper proposes a two-dimensional precision level for real-time measurement using a zoom fast Fourier transform (zoom FFT)-based decoupling algorithm that was developed and integrated in an FPGA. This algorithm solves the contradiction between obtaining high resolution and obtaining high measurement speed, and achieves both high angle-resolution measurement and real-time measurement. The proposed level adopts a silicone-oil surface as the angle-sensitive interface and combines the principle of homodyne interference. By analyzing the frequency of the interference fringes, the angle variation can be determined. The zoom-FFT-based decoupling algorithm improves the system’s frequency resolution of the interference fringes, thereby significantly enhancing the angle resolution. Furthermore, this algorithm improves the efficiency of angle decoupling, while the angle decoupling process can also be transplanted to the board to realize real-time measurement of the level. Finally, a prototype based on the level principle was tested to validate the effectiveness of the proposed method. The principle analysis and test results showed that the angle resolution of the prototype improved from 9 arcsec to about 0.1 arcsec using this angle-solution method. At the same time, the measurement repeatability of the prototype was approximately ±0.2 arcsec. In comparison with a commercial autocollimator, the angle measurement accuracy reached ±0.6 arcsec.

8 May 2023 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
Pengcheng HuPengcheng Hu
Pengcheng Hu
XLXionglei Lin
Xionglei Lin
YZYifan Zhang
Yifan Zhang
Liang YuLiang Yu
Liang Yu
With the rapid development of ultraprecision instruments, inclinometers play an essential role in machining and calibration. The current mainstream methods based on capacitance, inductance, or optoelectronic autocollimators can achieve a high resolution but they are not directly traceable. In addition, their systems are relatively complex and large. In this study, a novel dual-axis optoelectronic inclinometer is proposed, the tilt angle can be precisely measured by calculating the spatial frequency of wavefront interference fringes, and the liquid surface is applied as its reference. Compared with other interferometers and autocollimators, the proposed inclinometer is not sensitive to mechanical errors and the air refractive index. Therefore, the measurement result is directly traceable to gravity and the laser wavelength. A compact prototype was fabricated to verify the effectiveness of the proposed method. Our experimental results show that the prototype achieves a low longterm drift of 0.02 arcsec/h and a resolution of greater than 0.1 arcsec, with high sensitivity and stability. Compared with a commercial autocollimator, the linear error of the prototype was less than 0.16%.

15 July 2024 in IEEE Sensors Journal
Verified
Journal Article
Closed access
Pengcheng HuPengcheng Hu
Pengcheng Hu
XLXionglei Lin
Xionglei Lin
GMGabor Molnar
Gabor Molnar
CWChristian Werner
Christian Werner
HFHaijin Fu
Haijin Fu
Liang YuLiang Yu
Liang Yu
Camera-based three-degree-of-freedom (3DoF) interferometers can be used to simultaneously measure the displacement, yaw, and pitch. Furthermore, high precision can be achieved in these interfrometers with a fairly compact structure. However, they suffer from the problem of the 10-Hz-level frame rate of the used camera sensor, which limits their measurement speed to micrometer per second. Therefor, this study proposes a dual-parallel-pixel-row decoupling (DPPRD) method. Here, 3DoF results are decoupled using two pixel-rows rather than an entire image. Hence, the DPPRD can overcome the hardware limitations of the area-scan camera; therefore, the frame rate and measurement speed can be further improved. The features introduced by the DPPRD method, particularly the influence of pixel-row interval on pitch angle measurement, are analyzed and simulated. Further, a interferometer prototype is developed and optimized using an industrial area-scan camera to verify the feasibility of the proposed method. Experimental results show that the resolution can achieve 0.8 nm and 0.5 μrad levels, and the measurement accuracy can reach nanometer and microradian levels. The maximum measurement speed can be substantially improved approximately 44.25 times without modifying the hardware, and for some area-scan cameras the measurement speed can exceed 1 mm/s.

19 December 2025 in Measurement Science and Technology
Verified
Journal Article
Open access
Liang YuLiang Yu
Liang Yu
ZWZhiwei Wang
Zhiwei Wang
XLXionglei Lin
Xionglei Lin
Pengcheng HuPengcheng Hu
Pengcheng Hu
Haijin FuHaijin Fu
Haijin Fu
CWChristian Werner
Christian Werner
Advanced manufacturing, precision metrology, space exploration, and other fields increasingly rely on multi-degree-of-freedom (multi-DOF) and high-precision measurements. The demands of such measurement systems—structural complexity, systematic error control, and information decoupling—have challenged traditional interferometric techniques. Wavefront interference imaging, which integrates laser interferometry with image analysis, has emerged as an advanced technique capable of subnanometer displacement and submicroradian angular resolution using a single laser beam. This method has gained importance in multi-DOF measurement technologies because it simultaneously obtains ultra-precise multi-DOF measurements with a compact setup, strong decoupling capability, and high integrability. This review systematically examines the development of wavefront interference imaging. Beginning with physical modeling of interference fringes, it traces the evolution of representative measurement models from two-dimensional to six-DOF configurations and analyzes the potential integration of this technique with emerging deep learning–based fringe processing methods. The paper further discusses frequency and phase decoupling algorithms in both the spatial and spectral domains and summarizes recent applications of this technology to nanometric coordinate measurements, atomic force microscopy, laser leveling, and spacecraft systems. The transition of wavefront interference imaging, from single-DOF extraction to coupled modeling and real-time resolution of multi-DOFs, demonstrates the excellent system scalability and application potential of this technology. This review aims to establish a theoretical framework and developmental roadmap for wavefront interference imaging, facilitating the advancement of high-precision, high-dimensional measurement systems in related domains.

22 September 2025 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
XLXionglei Lin
Xionglei Lin
Pengcheng HuPengcheng Hu
Pengcheng Hu
ZWZhiwei Wang
Zhiwei Wang
GMGabor Molnar
Gabor Molnar
CWChristian Werner
Christian Werner
Liang YuLiang Yu
Liang Yu
Homodyne wavefront interferometry enables synchronous compensation of angle error in precision displacement measurement. However, the traditional decoupling method relies on image signal, and the measurement speed is typically only some $\mu $ m/s. This article proposes a method that employs a fiber array for spatial sparse sampling, in order to achieve fast and simultaneous measurement of displacement, pitch, and yaw angles. A novel decoupling algorithm is developed to calculate the three degrees of freedom (3DoFs), based on an elliptic trajectory formed by a few sampling point inside an interference beam spot. The experimental results indicated that the prototype can achieve a measurement speed of 158.2 mm/s, while the resolution can achieve 0.6 nm and $0.13~\mu $ rad. The prototype was compared against a commercial interferometer and autocollimator; the difference was at nanometer and microrad levels. Further, the prototype was used to calibrate a commercial piezo stage. The maximum motion speed of the stage is 3.3 mm/s, within a motion range of $100~\mu $ m, the repeatability achieves 1 nm, and the linear error is below 10 nm.