Insulation condition monitoring is essential for the safety of our distribution power gird. However, the traditional monitoring solution is hardly applied due to the concerns arise from natures of distribution grid, such as complex feeder networks, massive operation site and high economic benefit. In this paper, a wireless sensing network based on IoT technology is demonstrated for insulation condition perception. First of all, the general framework of the wireless sensing network is designed with considerations on extendibility and accessibility. Next, it goes into detail about the technical requirements of the essential units of the sensing network including sensor node, power management and data communication. With this concept, two practical cases of IoT-based partial discharge sensing networks realized on the switchgear cabinet and power cable are presented with details involving the design of TEV and HFCT sensor nodes, the energy consumption, Lora/NB-IoT-based network structures and data usage strategies. This IoT-based insulation condition monitoring is proven to be applicable for the distribution grid and expected to be references for more possible IoT applications.
Optical detection is reliable in intrinsically characterizing partial discharges (PDs). Because of the great volume and high-level power supply of the optical devices that can satisfy the requirements in photosensitivity, optical PD detection can merely be used in laboratory studies. To promote the practical application of the optical approach in an actual power apparatus, a silicon photomultiplier (SiPM)-based PD sensor is introduced in this paper, and its basic properties, which include the sensitivity, pulse resolution, correlation with PD severity, and electromagnetic (EM) interference immunity, are experimentally evaluated. The stochastic phase-resolved PD pattern (PRPD) for three typical insulation defects are obtained by SiPM PD detector and are compared with those obtained using a high-frequency current transformer (HFCT) and a vacuum photomultiplier tube (PMT). Because of its good performances in the above aspects and its additional advantages, such as the small size, low power supply, and low cost, SiPM offers great potential in practical optical PD monitoring.
Sulfur hexafluoride (SF6) gas-insulated electrical equipment is widely used in high-voltage (HV) and extra-high-voltage (EHV) power systems. Partial discharge (PD) and local heating can occur in the electrical equipment because of insulation faults, which results in SF6 decomposition and ultimately generates several types of decomposition products. These SF6 decomposition products can be qualitatively and quantitatively detected with relevant detection methods, and such detection contributes to diagnosing the internal faults and evaluating the security risks of the equipment. At present, multiple detection methods exist for analyzing the SF6 decomposition products, and electrochemical sensing (ES) and infrared (IR) spectroscopy are well suited for application in online detection. In this study, the combination of ES with IR spectroscopy is used to detect SF6 gas decomposition. First, the characteristics of these two detection methods are studied, and the data analysis matrix is established. Then, a qualitative and quantitative analysis ES-IR model is established by adopting a two-step approach. A SF6 decomposition detector is designed and manufactured by combining an electrochemical sensor and IR spectroscopy technology. The detector is used to detect SF6 gas decomposition and is verified to reliably and accurately detect the gas components and concentrations.
Metal-enclosed switchgear, which are widely used in the distribution of electrical energy, play an important role in power distribution networks. Their safe operation is directly related to the reliability of power system as well as the power quality on the consumer side. Partial discharge detection is an effective way to identify potential faults and can be utilized for insulation diagnosis of metal-enclosed switchgear. The transient earth voltage method, an effective non-intrusive method, has substantial engineering application value for estimating the insulation condition of switchgear. However, the practical application effectiveness of TEV detection is not satisfactory because of the lack of a TEV detection application method, i.e., a method with sufficient technical cognition and analysis. This paper proposes an innovative online PD detection system and a corresponding application strategy based on an intelligent feedback distributed TEV wireless sensor network, consisting of sensing, communication, and diagnosis layers. In the proposed system, the TEV signal or status data are wirelessly transmitted to the terminal following low-energy signal preprocessing and acquisition by TEV sensors. Then, a central server analyzes the correlation of the uploaded data and gives a fault warning level according to the quantity, trend, parallel analysis, and phase resolved partial discharge pattern recognition. In this way, a TEV detection system and strategy with distributed acquisition, unitized fault warning, and centralized diagnosis is realized. The proposed system has positive significance for reducing the fault rate of medium voltage switchgear and improving its operation and maintenance level.
13 September 2018 in IEEE Transactions on Power Delivery
This paper proposes a joint visualization detection method to diagnose outdoor insulation status of high-voltage (HV) equipment in substations, which applies image matching and fusion techniques to accurately combine the results of ultrasonic, ultraviolet, and infrared detection in an image. This image can then be used to quickly and clearly locate the region of corona discharge and overheating of outdoor substation HV equipment. First, ultrasonic localization visualization of corona discharge is proposed, which is based on the designed double-helix array and multi-signal classification algorithm. This method provides a more intuitive way for the diagnosis of outdoor insulation status. Then, ultraviolet localization visualization method is detailed, and an adaptive affine matrix is designed for the accurate location of corona discharge. Following this, infrared-visible detection of overheating failure is introduced, and the speeded-up robust features (SURF) algorithm and random sample consensus (RANSAC) algorithm are used to implement image fusion process. Finally, the results of image fusion are provided, and location error evaluations are conducted for each module. With acceptable cost and advantages of three detection method, the proposed visualization method is used for evaluating the insulation status of substation equipment more intuitively and conveniently, and thus has an extensive application prospect.
21 May 2020 in IEEE Transactions on Power Electronics
Exposed metal or insulator to air interfaces are widely existing in medium voltage SiC based converters. To address external insulation along such interfaces properly, large insulation distance in air is applied. However, such insulation tends to significantly impair converter power densities and performances. Targeting on the external discharge free design, design suggestions which can reflect the relationship between insulation structures and square wave excitation parameters, are highly demanded. Moreover, due to possible fabrication issues and insulation degradation, massive external discharges may still occur, even that they should be eliminated by design. Therefore, insulation assessment along the entire system, or at least for critical components, is necessary. In this paper, silicon photomultiplier (SiPM) based external discharge detection solutions are introduced. Then, for a self-designed SiC based medium voltage converter, SiPM sensors help both its external insulation design and assessment. By using SiPM sensors, two types of external discharges are characterized under square wave excitation and thus general design suggestions are developed. Moreover, as shown by two examples, SiPM sensors can be used to assess the external insulation for converter applications.