Reducing the rotation period through thinning and changing planting spacing can influence the technological properties of wood, with little attention paid to the effects of these variables on the raw material, which limits its processing in the wood sector. This work aimed to evaluate the physical and mechanical properties of wood from Anadenanthera peregrina juveniles thinned in three planting spacings (3 m × 3 m, 4 m × 4 m, and 5 m × 5 m). The physical properties in the base-top and pith–shell directions and the mechanical properties of the samples were evaluated. The results indicate better technological properties for wood with larger spacings. The physical properties showed decreasing trends in the base-top direction and increasing trends in the pith-bark direction, with a distinct trend in the degree of collapse. The average basic density of the different planting spacings varied between 0.47 g cm−3 and 0.63 g cm−3. The mechanical properties obtained for the 4 m × 4 m spacing were superior to those of the other spacings. Wood from young A. peregrina is an alternative for industrial processing, as wood from higher planting densities is more suitable for purposes that require resistance and rigidity.
Se identificó la influencia del tratamiento térmico en la obtención de compuestos tánicos condensables a partir de residuos de corteza de Pinus spp para la producción de adhesivo. Los tratamientos térmicos fueron: (a) corteza sin tratamiento térmico (testigo); (b) corteza expuesta a 60 °C durante 50 h en seco; (c) corteza expuesta a 120 °C durante 10 h en vapor; (d) corteza adherida al tronco expuesta a 120 °C durante 10 h en vapor. Para su caracterización química, la corteza fue molida y clasificada. Se extrajeron los compuestos tánicos mediante reflujo con agua destilada durante 2 h; se adicionaron sales de carbonato de sodio y sulfito de sodio, ambos a 5% en relación con la masa seca. Para el testigo fueron evaluadas las propiedades del tanino comercial de Acacia mearnsii (acacia negra). El proceso de extracción de taninos fue realizado en autoclave y se evaluaron las siguientes propiedades: viscosidad, pH, tiempo de formación de gel, contenido de sólidos y densidad. Tanto la corteza expuesta a 120 °C durante 10 horas en vapor como la adherida al tronco sometida a 120 °C a vapor durante 10 h, para ambas sales, exhibieron los mayores rendimientos de taninos. Los extractos tánicos obtenidos a partir de carbonato de sodio presentaron una estructura alcalina, alta viscosidad y menor tiempo de formación de gel. Sin embargo, los extractos obtenidos a partir de sulfito de sodio proporcionaron un carácter ácido y contenido de sólidos próximos a los encontrados en los extractos tánicos acuosos obtenido de la acacia negra.
The development of biomass-based adhesives has attracted interest as an alternative to petroleum-derived synthetic and potentially toxic adhesives. Pachira aquatica oil is a renewable raw material that can be incorporated into an MDI-based polyurethane system. In this study, the chemical composition and reactivity of P. aquatica oil were characterized using GC–MS, FTIR, and hydroxyl index measurements. The oil showed a predominance of saturated fatty acids, particularly methyl hexadecanoate (64.80%), derived from palmitic acid, and exhibited a low initial hydroxyl value. To enhance reactivity, the oil was transesterified with glycerol under different conditions, producing polyols with substantially increased hydroxyl values (412–769 mg KOH g−1), as confirmed by the intensified O–H and C–O bands in the FTIR spectra. The polyurethane adhesives were formulated from the selected polyols (P3 and P4) and evaluated at different NCO/OH ratios and pressing temperatures, using ABES shear tests. The highest ABES shear strength recorded was approximately 3.6 MPa, obtained for isocyanate indices between 0.8 and 1.0 and temperatures around 115 °C. Although this value represents the best performance among the tested conditions, it remains below the industrial benchmarks typically associated with the EN 205 standard (≈10 MPa). It is important to note that the ABES and EN 205 methods are not directly comparable due to differences in testing protocols. Nevertheless, the results indicate that, under the evaluated conditions, the adhesives exhibit limited mechanical performance and require further optimization.
RESUMO Neste trabalho obteve-se corpos de prova provenientes de painéis aglomerados confeccionados a partir de resíduos de madeira serrada de eucalipto. Caracterizou-se o módulo de elasticidade a partir da frequência flexional e longitudinal e módulo de cisalhamento por meio de ensaios não destrutivo e destrutivo. Foram avaliadas a resistência biológica dos painéis a partir da reação aos fungos Neolentinus lepideus e Brunneoporus malicola (≈ Gloeopyllum trabeum) e com térmitas Cryptotermes brevis e Nasutitermes sp. Nestes ensaios determinou-se a perda de massa após o período de ataque. Observou-se relação entre o método de vibração flexional do corpo de prova retangular com o módulo de elasticidade estático, possibilitando o uso desse método. Os painéis com menor teor de tanino (2%) no adesivo apresentaram desempenhos mecânicos inferiores. As técnicas utilizadas mostraram ser possível a estimação das propriedades em painéis aglomerados. Os painéis apresentaram-se mais resistentes para o fungo B. malicola com as menores perdas de massa (média geral de 15,73%) em relação ao N. lepideus (45,73%). Os painéis confeccionados com 100 % de tanino-formaldeído promoveram maior perda de massa quando em contato com a térmita Cryptotermes brevis (12,54%) e para ambos os fungos B. malicola (21,2%) e N. lepideus (53,8%). Para as térmitas Nasutitermes sp. os painéis com 100% de tanino foram menos degradados.
Wastes, biomasses, and nanoparticles have motivated reformulations of adhesives in the wood-based-panel industry. This study investigated the incorporation of glass wool (GW) waste as a filler material in urea–formaldehyde (UF) adhesive, evaluating its effects on the adhesive properties as well as on the physical, mechanical, fire-retardant, and acoustic properties of particleboards. Panels with a target density of 700 kg m−3 were produced with different proportions of glass wool in the adhesive (T1: 0%; T2: 3.34%; T3: 4.93%; T4: 6.52%; T5: 9.49%; T6: 12.35%). The adhesive-coated particle mat was pressed in a hydraulic press at 160 °C under a compression force of 72 tons for 10 min. The panels were subjected to analyses of their physical, mechanical, fire-retardant, and acoustic properties, as well as scanning electron microscopy (SEM) analyses. Statistical analysis involved regression, analysis of variance, and a Scott–Knott test (p < 0.05). The results indicated that adding 3.34% GW to the adhesive improved the modulus of rupture, internal bond strength, screw withdrawal resistance, and acoustic efficiency of the panels. A glass wool content of 12.35% enhanced the hardness and the damping factor. These findings highlight the potential of glass wool as a functional filler material in UF adhesive, promoting the development of stronger and more sustainable particleboards.
The replacement of synthetic fibers with lignocellulosic reinforcements has gained increasing attention due to their low cost, renewability, and environmental benefits. In this context, Hedychium coronarium (wild ginger), an invasive species with high biomass yield, was investigated as a novel fiber source for epoxy composites. Leaf sheath fibers (FLHC) were characterized for chemical composition, crystallinity (73.23%), crystallite size (2.56 nm), morphology, and tensile strength (196.6 MPa). Epoxy composites reinforced with 10, 20, and 30 wt% FLHC were evaluated through mechanical testing, thermal analysis (TGA/DTG), FTIR spectroscopy, and scanning electron microscopy. Fiber incorporation progressively enhanced tensile strength (59.98 MPa at 30 wt% loading), increased the elastic modulus by up to 250%, and tripled impact resistance, although limited fiber–matrix adhesion constrained further improvements in toughness. This study is novel in demonstrating, for the first time, that FLHC can function as a high‑quality reinforcement in epoxy composites, reducing demand for synthetic resins and valorising biomass from an invasive species.